|
|
This chapter describes the function and displays the syntax of each ATM command. For more information about defaults and usage guidelines, see the corresponding chapter of the Wide-Area Networking Command Reference.
atm arp-server [self [time-out minutes] | nsap nsap-address]
To identify an ATM Address Resolution Protocol (ARP) server for the IP network or set time-to-live (TTL) values for entries in the ATM ARP table, use the arp-server interface configuration command.
| self | (Optional) Specifies the current router as the ATM ARP server. |
| time-out minutes | (Optional) Number of minutes a destination entry listed in the ATM ARP server's ARP table will be kept before the server takes any action to verify or time out the entry. |
| nsap nsap-address | (Optional) Network service access point (NSAP) address of an ATM ARP server. |
To enable support for ATM adaptation layer 3/4 (AAL3/4) on an ATM interface, use the atm aal aal3/4 interface configuration command.
To enable the router to engage in address registration and callback functions with the Interim Local Management Interface (ILMI), use the atm address-registration interface configuration command. To disable ILMI address registration functions, use the no form of this command.
atm backward-max-burst-size-clp0 cell-count
no atm backward-max-burst-size-clp0
To change the maximum number of high-priority cells coming from the destination router to the source router at the burst level on the switched virtual circuit (SVC), use the atm backward-max-burst-size-clp0 map-class configuration command. The no form of this command restores the default.
| cell-count | Maximum number of high-priority cells coming from the destination router at the burst level. Default is -1. |
atm backward-max-burst-size-clp1 cell-count
no atm backward-max-burst-size-clp1
To change the maximum number of low-priority cells coming from the destination router to the source router at the burst level on the SVC, use the atm backward-max-burst-size-clp1 map-class configuration command. The no form of this command restores the default value.
| cell-count | Maximum number of low-priority cells coming from the destination router at the burst level. Default is -1. |
atm backward-peak-cell-rate-clp0 rate
no atm backward-peak-cell-rate-clp0
To change the peak rate of high-priority cells coming from the destination router to the source router on the SVC, use the atm backward-peak-cell-rate-clp0 map-class configuration command. The no form of this command restores the default.
| rate | Maximum rate in kilobits per second (kbps) at which this SVC can receive high-priority cells from the destination router. Default is -1. Maximum upper range is 155,000 kbps. |
atm backward-peak-cell-rate-clp1 rate
no atm backward-peak-cell-rate-clp1
To change the peak rate of low-priority cells coming from the destination router to the source router on the SVC, use the atm backward-peak-cell-rate-clp1 map-class configuration command. The no form of this command restores the default.
| rate | Maximum rate in kilobits per second (kbps) that this SVC can receive low-priority cells from the destination router. The default is -1. Maximum value is 155,000 kbps. |
atm backward-sustainable-cell-rate-clp0 rate
no atm backward-sustainable-cell-rate-clp0
To change the sustainable rate of high-priority cells coming from the destination router to the source router on the SVC, use the atm backward-sustainable-cell-rate-clp0 map-class configuration command. The no form of this command restores the default.
| rate | Sustainable rate in kilobits per second (kbps) at which this SVC can receive high-priority cells from the destination router. Default is -1. Maximum upper range is 155,000 kbps. |
atm backward-sustainable-cell-rate-clp1 rate
no atm backward-sustainable-cell-rate-clp1
To change the sustainable rate of low-priority cells coming from the destination router to the source router on the SVC, use the atm backward-sustainable-cell-rate-clp1 map-class configuration command. The no form of this command restores the default value.
| rate | Sustainable rate in kilobits per second (kbps) at which this SVC can receive low-priority cells from the destination router. Default is -1. Maximum upper range is 155,000 kbps. |
To cause the ATM Interface Processor (AIP) to generate the transmit clock internally, use the atm clock internal interface configuration command. The no form of this command restores the default value.
[no] atm esi-address esi.selector
To enter the End Station ID (ESI) and selector byte fields of the ATM NSAP address, use the atm esi-address interface configuration command. The NSAP address prefix is filled in via ILMI from the ATM switch.
| esi | End Station Id field value in hexadecimal; 6 bytes long. |
| selector | Selector field value in hexadecimal; 1 byte long. |
atm exception-queue number
no atm exception-queue
To set the exception queue length, use the atm exception-queue interface configuration command. The no form of this command restores the default value.
| number | Number of entries in the range of 8 to 256. Default is 32 entries. |
atm forward-max-burst-size-clp0 cell-count
no atm forward-max-burst-size-clp0
To change the maximum number of high-priority cells going from the source router to the destination router at the burst level on the SVC, use the atm forward-max-burst-size-clp0 map-class configuration command. The no form of this command restores the default value.
| cell-count | Maximum number of high-priority cells going from the source router at the burst level. Default is -1. |
atm forward-max-burst-size-clp1 cell-count
no atm forward-max-burst-size-clp1
To change the maximum number of low-priority cells going from the source router to the destination router at the burst level on the SVC, use the atm forward-max-burst-size-clp1 map-class configuration command. The no form of this command restores the default value.
| cell-count | Maximum number of low-priority cells going from the source router at the burst level. Default is -1. |
atm forward-peak-cell-rate-clp0 rate
no atm forward-peak-cell-rate-clp0
To change the peak rate of high-priority cells going from the source router to the destination router on the SVC, use the atm forward-peak-cell-rate-clp0 map-class configuration command. The no form of this command restores the default value.
| rate | Maximum rate in kilobits per second (kbps) at which this SVC can send high-priority cells from the source router. Default is -1. Maximum upper range is 155,000 kbps. |
atm forward-peak-cell-rate-clp1 rate
no atm forward-peak-cell-rate-clp1
To change the peak rate of low-priority cells coming from the source router to the destination router on the SVC, use the atm forward-peak-cell-rate-clp1 map-class configuration command. The no form of this command restores the default value.
| rate | Maximum rate in kilobits per second (kbps) at which this SVC can send low-priority cells from the source router. Default is -1. Maximum upper range is 155,000 kbps. |
atm forward-sustainable-cell-rate-clp0 rate
no atm forward-sustainable-cell-rate-clp0
To change the sustainable rate of high-priority cells coming from the source router to the destination router on the SVC, use the atm forward-sustainable-cell-rate-clp0 map-class configuration command. The no form of this command restores the default value.
| rate | Sustainable rate in kilobits per second (kbps) at which this SVC can send high-priority cells from the source router. Default is -1. Maximum upper range is 155,000 kbps. |
atm forward-sustainable-cell-rate-clp1 rate
no atm forward-sustainable-cell-rate-clp1
To change the sustainable rate of low-priority cells coming from the source router to the destination router on the SVC, use the atm forward-sustainable-cell-rate-clp1 map-class configuration command. The no form of this command restores the default value.
| rate | Sustainable rate in kilobits per second (kbps) at which this SVC can send low-priority cells from the source router. Default is -1. Maximum upper range is 155,000 kbps. |
To specify E3 line framing, use the atm framing interface configuration command. To return to the default G.751 Physical Layer Convergence Protocol (PLCP) framing, use the no form of this command.
| g832adm | Specifies G.832 ATM direct mapping. |
atm idle-timeout seconds
no atm idle-timeout
To change the idle timer for SVCs on an interface that will cause the SVCs to disconnect when inactive for a specified interval, use the atm idle-timeout interface configuration command. To return to the default setting, use the no form of this command.
| seconds | Number of seconds the SVC can be inactive before disconnecting. Setting seconds to 0 disables idle timeouts. |
[no] atm ilmi-keepalive [seconds]
To enable Interim Local Management Interface (ILMI) keepalives, use the atm ilmi-keepalive interface configuration command. To disable ILMI keepalives, use the no form of this command.
| seconds | Number of seconds between keepalives. The default is 3 seconds. Values less than 3 seconds are rounded to 3 seconds, and there is no upper bound to the range of values. |
To set the ceiling value of the virtual circuit descriptor (VCD) on the AIP card, use the atm maxvc interface configuration command. To restore the default value, use the no form of this command.
| number | Maximum number of supported virtual circuits. Valid values are 256, 512, 1024, 2048, or 4096. Default is 2048. |
To limit the number of message identifier (MID) numbers allowed on each virtual circuit, use the atm mid-per-vc interface configuration command.
| maximum | Number of MIDs allowed per virtual circuit on this interface. The values allowed are 16, 32, 64, 128, 256, 512, and 1024. The default is 16 MIDs per virtual circuit. |
To assign an Switched Multimegabit Data Service (SMDS) E.164 multicast address to the ATM subinterface that supports AAL3/4 and SMDS encapsulation, use the atm multicast interface configuration command.
| address | Multicast E.164 address assigned to the subinterface. |
[no] atm multipoint-interval interval
To specify how often new destinations can be added to multipoint calls to an ATM switch in the network, use the atm multipoint-interval interface configuration command. To return to the default interval, use the no form of this command.
| interval | Interval length in seconds, in the range between 0 and 4294967. The default is 30 seconds. |
To enable point-to-multipoint signaling to the ATM switch, use the atm multipoint-signaling interface configuration command. To disable point-to-multipoint signaling to the ATM switch, use the no form of this command.
[no] protocol protocol-address atm-nsap atm-nsap-address [class class-name] [broadcast]
To define an ATM map statement for an SVC, use the atm-nsap map-list configuration command in conjunction with the map-list global configuration command. The no form of this command removes the address.
| protocol | One of the following keywords: appletalk, apollo, bridge, clns, decnet, ip, ipx, vines, xns. |
| protocol-address | Destination address that is being mapped to this SVC. |
| atm-nsap-address | Destination ATM NSAP address. Must be exactly 40 hexadecimal digits long and in the correct dotted format. |
| class class-name | (Optional) Name of a table that contains encapsulation-specific parameters. Such a table can be shared between maps that have the same encapsulation. |
| broadcast | (Optional) Indicates this map entry is to be used when the corresponding protocol sends broadcast packets to the interface--for example, Interior Gateway Routing Protocol (IGRP) updates. |
atm nsap-address nsap-address
no atm nsap-address
To set the NSAP address for an ATM interface using SVC mode, use the atm nsap-address interface configuration command. The no form of this command removes any configured address for the interface.
| nsap-address | The 40-digit hexadecimal NSAP address of this interface (the source address). |
[no] atm pvc vcd vpi vci aal-encap [[midlow midhigh] [peak average burst]] [oam seconds] [inarp minutes]
To create a permanent virtual circuit (PVC) on the AIP or NPM interface and, optionally, to generate Operation, Administration, and Maintenance (OAM) F5 loopback cells or enable Inverse ATM ARP, use the atm pvc interface configuration command. The no form of this command removes the specified PVC.
| vcd | Virtual circuit descriptor. A unique number per AIP or NPM that identifies to the processor which VPI-VCI pair to use for a particular packet. Valid values range from 1 to the value set with the atm maxvc command. The AIP or NPM requires this feature to manage packet transmission. The vcd value is not associated with the VPI-VCI pair used for the ATM network cells. |
| vpi | ATM network virtual path identifier (VPI) of this PVC, in the range from 0 through 255. The VPI is an 8-bit field in the header of the ATM cell. The VPI value is unique only on a single link, not throughout the ATM network because it has local significance only. The VPI value must match that of the switch.
Both vpi and vci cannot be specified as 0; if one is 0, the other cannot be 0. |
| vci | ATM network virtual channel identifier (VCI) of this PVC, in the range of 0 through 65535. The VCI is a 16-bit field in the header of the ATM cell. The VCI value is unique only on a single link, not throughout the ATM network because it has local significance only.
Both vpi and vci cannot be specified as 0; if one is 0, the other cannot be 0. |
| aal-encap | ATM adaptation layer (AAL) and encapsulation type. When aal5mux is specified, a protocol is required. Possible values are as follows:
· aal34smds--encapsulation for SMDS networks; not supported on the Cisco 4500. · aal5nlpid--encapsulation that allows ATM interfaces to interoperate with High-Speed Serial Interfaces (HSSIs) that are using an ATM data service unit (ADSU) and running ATM-Data Exchange Interface (DXI). · aal5mux decnet--A MUX-type virtual circuit. · aal5mux ip--A MUX-type virtual circuit. · aal5mux novell--A MUX-type virtual circuit. · aal5mux vines--A MUX-type virtual circuit. · aal5mux xns--A MUX-type virtual circuit. · aal5snap--Logical Link Control/Subnetwork Access Protocol (LLC/SNAP) precedes the protocol datagram. This is the only encapsulation supported for Inverse ARP. · ilmi--Used to set up communication with the ILMI; the associated vpi and vci values are ordinarily 0 and 16, respectively. · qsaal--A signaling-type PVC used for setting up or tearing down SVCs; the associated vpi and vci values are ordinarily 0 and 5, respectively. |
| midlow | (Optional) Starting message identifier (MID) number for this PVC. The default is 0. If you set the peak, average, and burst values, you must also set the midlow and midhigh values. |
| midhigh | (Optional) Ending MID number for this PVC. The default is 0. If you set the peak, average, and burst values, you must also set the midlow and midhigh values. |
| peak | (Optional) Maximum rate (in kbps) at which this virtual circuit can transmit. Valid values are in the range from 1 to the maximum rate set for a rate queue. The value should match a value specified by the atm rate-queue command. If you set this value, you must also specify a value for the average, burst, midlow, and midhigh arguments. |
| average | (Optional) Average rate (in kbps) at which this virtual circuit will transmit. Valid values are in the range from 1 to the maximum rate set for a rate queue. If you set this value, you must also specify a value for the peak, burst, midlow, and midhigh arguments. |
| burst | (Optional) Value (in the range 1 through 2047) that relates to the maximum number of ATM cells the virtual circuit can transmit to the network at the peak rate of the PVC. The actual burst cells equals burst * 32 cells, thereby allowing for a burst size of 32 cells to 65504 cells. The largest practical value of burst is the maximum transmission unit (MTU) size of the AIP card. If you set this value, you must also specify a value for the peak and average arguments. |
| oam seconds | (Optional) Specifies how often to generate an OAM F5 loopback cell from this virtual circuit. The default value is 10 seconds. |
| inarp minutes | (Optional) Specifies how often Inverse ARP datagrams will be sent on this virtual circuit. The default value is 15 minutes. |
atm rate-queue queue-number speed
no atm rate-queue
To create a permanent rate queue for the AIP or NPM, use the atm rate-queue interface configuration command. The no form of this command removes the rate queue.
| queue-number | Queue number in the range 0 through 7. Queues 0 through 3 are in the high-priority bank, and queues 4 through 7 are in the low-priority bank. |
| speed | Speed in megabits per second (Mbps) in the range from 1 through 155. The maximum speed is determined by the detected PLIM type on the AIP or NPM:
· 34 Mbps for E3 · 45 Mbps for DS-3 · 100 Mbps for Transparent Asynchronous Transmitter/Receiver Interface (TAXI) · 155 Mbps for Synchronous Optical Network (SONET) |
atm rawq-size number
no atm rawq-size
To define the AIP raw queue size, use the atm rawq-size interface configuration command. The no form of this command restores the default value.
| number | Maximum number of cells in the raw queue simultaneously, in the range 8 through 256. The default is 32. |
atm rxbuff number
no atm rxbuff
To set the maximum number of receive buffers for simultaneous packet reassembly, use the atm rxbuff interface configuration command. The no form of this command restores the default value.
| number | Maximum number of packet reassemblies that the AIP can perform simultaneously, in the range 0 through 512. Default is 256. |
atmsig close atm slot/0 vcd (Cisco 7000 series routers)
atmsig close atm number vcd (Cisco 4000 series routers)
To disconnect an SVC, use the atmsig close EXEC command.
| slot | ATM slot number on the Cisco 7000 routers. |
| vcd | Virtual circuit descriptor of the signaling PVC to close. |
| number | ATM network processor module number on the Cisco 4000 series routers. |
To assign a unicast E.164 address to the ATM subinterface that supports AAL3/4 and SMDS encapsulation, use the atm smds-address interface configuration command.
| address | Unicast E.164 address assigned to the subinterface. |
[no] atm sonet [sts-3c | stm-1]
To set the proper mode of operation for the SONET PLIM, use the atm sonet interface configuration command. The no form of this command restores the default.
| sts-3c | STS-3c access. |
| stm-1 | STM-1 access. |
atm txbuff number
no atm txbuff
To set the maximum number of transmit buffers for simultaneous packet fragmentation, use the atm txbuff interface configuration command. The no form of this command restores the default value.
| number | Maximum number of packet fragmentations that the AIP can perform simultaneously, in the range 0 through 512. Default is 256. |
[no] protocol protocol-address atm-vc vcd [broadcast]
To define an ATM map statement for a PVC, use the atm-vc map-list configuration command in conjunction with the map-list global configuration command. The no form of this command removes the address.
| protocol | One of the following keywords: appletalk, apollo, bridge, clns, decnet, ip, ipx, vines, xns. |
| protocol-address | Destination address that is being mapped to this PVC. |
| vcd | Virtual circuit descriptor of the PVC. |
| broadcast | (Optional) Indicates that this map entry is to be used when the corresponding protocol sends broadcast packets to the interface--for example, IGRP updates. Provides pseudobroadcasting support. |
atm vc-per-vp number
no atm vc-per-vp
To set the maximum number of VCIs to support per VPI, use the atm vc-per-vp interface configuration command. The no form of this command restores the default value.
| number | Maximum number of VCIs to support per VPI. On the Cisco 7000 AIP, valid values are 32, 64, 128, 256, 512, 1024, 2048, or 4096. On the Cisco 4500 NPM, valid values are 32, 64, 128, 256, 512, 1024, 2048, 4096, or 8192. Default is 1024. |
atm vp-filter hexvalue
no atm vp-filter
To set the AIP filter register, use the atm vp-filter interface configuration command. The no form of this command restores the default value.
| hexvalue | Value in hexadecimal format. Default is 0x7B. |
To enable scrambling of the ATM cell payload for the DS-3 PLIM, use the ds3 scrambling global configuration command. To disable scrambling of the ATM cell payload for the DS-3 PLIM, use the no form of this command.
dxi map protocol protocol-address vpi vci [broadcast]
no dxi map protocol protocol-address
To map a protocol address to a given VPI and VCI, use the dxi map interface configuration command. Use the no form of this command to remove the mapping for that protocol and protocol address.
| protocol | The bridging or protocol keyword: apollo, appletalk, bridge, clns, decnet, ip, novell, vines, or xns. |
| protocol-address | Protocol-specific address. |
| vpi | Virtual path identifier in the range 0 to 15. |
| vci | Virtual circuit identifier in the range 0 to 63. |
| broadcast | (Optional) Broadcasts should be forwarded to this address. |
[no] dxi pvc vpi vci [snap | nlpid | mux]
Use the dxi pvc interface configuration command to configure multiprotocol or single protocol ATM-DXI encapsulation. The no form of this command disables multiprotocol ATM-DXI encapsulation.
| vpi | ATM network virtual path identifier (VPI) of this PVC, in the range from 0 through 255. The VPI is an 8-bit field in the header of the ATM cell. The VPI value is unique only on a single interface, not throughout the ATM network because it has local significance only.
Both vpi and vci cannot be specified as 0; if one is 0, the other cannot be 0. |
| vci | ATM network virtual channel identifier (VCI) of this PVC, in the range of 0 through 65535. The VCI is a 16-bit field in the header of the ATM cell. The VCI value is unique only on a single interface, not throughout the ATM network because it has local significance only.
Both vpi and vci cannot be specified as 0; if one is 0, the other cannot be 0. |
| snap | (Optional) LLC/SNAP encapsulation based on the protocol used in the packet. This keyword defines a PVC that can carry multiple network protocols. This is the default. |
| nlpid | (Optional) RFC 1294/1490 encapsulation. This option is provided for backward compatibility with the default encapsulation in earlier versions of the Cisco IOS software. |
| mux | (Optional) MUX encapsulation; the carried protocol is defined by the dxi map command when the PVC is set up. This keyword defines a PVC that carries only one network protocol. |
[no] loopback [diagnostic | line]
To place the ATM interface (AIP on the Cisco 7000 AIP series or NPM on the Cisco 4500 NPM) into loopback mode, use the loopback interface configuration command. The no form of this command removes the loopback.
| diagnostic | Place the interface into internal loopback mode. |
| line | Place the interface into external loopback mode. This is the default. |
[no] map-class encapsulation class-name
To enter map-class configuration mode to define quality of service (QOS) parameters that are associated with a static map for an SVC, use the map-class global configuration command. The no form of this command deletes this class.
| encapsulation | Encapsulation type. One of the following: atm, dialer, frame-relay, smds, or x25. |
| class-name | User-assigned name of the QOS parameters table. |
To associate an ATM map list to an interface or subinterface for either a PVC or SVC, use the map-group interface configuration command. The no form of this command removes the reference to the map list.
| name | Name of the map list identified by the map-list command. |
To define an ATM map statement for either a PVC or SVC, use the map-list global configuration command. The no form of this command deletes this list and all associated map statements.
| name | Name of the map list. |
show atm arp-server [atm slot/port[.subinterface-number]] (Cisco 7000 series routers)
show atm arp-server [atm number[.subinterface-number]] (Cisco 4500 routers)
To display the ATM ARP server's information about one specific interface or all interfaces, use the show atm arp-server user EXEC command.
| atm slot/port | (Optional) ATM slot and port numbers on the Cisco 7000 AIP series routers. |
| atm number | (Optional) ATM network processor module number on the Cisco 4500 series routers. |
| .subinterface-number | (Optional) Subinterface number. |
show atm interface atm slot/port (Cisco 7000 series)
show atm interface atm number (Cisco 4500)
To display ATM-specific information about an ATM interface, use the show atm interface atm privileged EXEC command.
| slot/port | Slot number and port number of the AIP. |
| number | NPM number. |
To display the list of all configured ATM static maps to remote hosts on an ATM network, use the show atm map privileged EXEC command.
To display current, global ATM traffic information to and from all ATM networks connected to the router, use the show atm traffic privileged EXEC command.
To display all active ATM virtual circuits (PVCs and SVCs) and traffic information, use the show atm vc privileged EXEC command.
| vcd | (Optional) Specifies which virtual circuit to display information about. |
To display all the protocol addresses mapped to a serial interface, use the show dxi map EXEC command.
To display the PVC statistics for a serial interface, use the show dxi pvc EXEC command.
To show Service-Specific Connection-Oriented Protocol (SSCOP) details for all ATM interfaces, use the show sscop privileged EXEC command.
sscop cc-timer seconds
no sscop cc-timer
To change the connection control timer, use the sscop cc-timer interface configuration command. The no form of this command restores the default value.
| seconds | Number of seconds between Begin messages. Default is 10 seconds. |
[no] sscop keepalive-timer seconds
To change the keepalive timer, use the sscop keepalive-timer interface configuration command. The no form of this command restores the default value.
| seconds | Number of seconds the router waits between transmission of POLL PDUs when no SD or SDP PDUs are queued for transmission or are outstanding pending acknowledgments. |
sscop max-cc retries
no sscop max-cc
To change the retry count of connection control, use the sscop max-cc interface configuration command. The no form of this command restores the default value.
| retries | Number of times that SSCOP will retry to transmit BGN (establishment), END (release), or RS (resynchronization) PDUs as long as an acknowledgment has not been received. Valid range is 1 to 6000. |
sscop poll-timer seconds
no sscop poll-timer
To change the poll timer, use the sscop poll-timer interface configuration command. The no form of this command restores the default value.
| seconds | Number of seconds the router waits between transmission of POLL PDUs. |
sscop rcv-window packets
no sscop rcv-window
To change the receiver window, use the sscop rcv-window interface configuration command. The no form of this command restores the default value.
| packets | Number of packets the interface can receive before it must send an acknowledgment to the ATM switch. Valid range is 1 to 6000. The default is 7 packets. |
sscop send-window packets
no sscop send-window
To change the transmitter window, use the sscop send-window interface configuration command. The no form of this command restores the default value.
| packets | Number of packets the interface can send before it must receive an acknowledgment from the ATM switch. Valid range is 1 to 6000. |
|
|