|
|
This appendix contains configuration examples for connecting a Cisco 700 series router to a router running Cisco IOS software. In these examples, the remote router is a Cisco 765 series router, and the central site router is a Cisco 4500 series router. Any Cisco 700 series router can be used in place of the remote Cisco 765 series router. Any router running Cisco IOS software can replace the central site Cisco 4500 series router.
In these examples, the Cisco 4500 series router serial interface configuration is an ISDN Primary Rate Interface (PRI) interface. Depending on the router model used at the central site, the serial interface may be a different type.
In addition, this appendix lists several interoperability issues that exist between Cisco IOS software and Cisco 700 series routers. These issues must be considered if you are connecting your Cisco 700 series router to a router running Cisco IOS software.
This appendix contains the following sections:
This section describes how to configure the routers for Internet Protocol (IP) static routing and callback with Challenge Handshake Authentication Protocol (CHAP).
Figure A-1 illustrates the configuration used in this example.
Following is the command summary for configuring the remote Cisco 765 series router for IP static routing and callback with CHAP authentication:
set switch 5ess set system 765 set ppp authentication incoming chap set ppp secret <765> set multidestination on cd lan set ip address 192.168.147.9 set ip netmask 255.255.255.248 set ip routing on set ip rip update periodic cd set user 4500 set ppp secret client <765> set ppp secret host <4500> set ip address 172.16.125.7 set ip netmask 255.255.255.0 set ip routing on set ip framing none set ppp callback request always set ip route destination 0.0.0.0 ga 172.16.125.1 propagate on set number 5558011 set bridging off set ip rip update off set timeout 360 set active reboot
For detailed information regarding the commands listed here, refer to the related chapter in this publication.
Following is the command summary for configuring a central site Cisco 4500 series router for IP static routing and callback with CHAP authentication:
For detailed information regarding the commands listed here, refer to the documentation provided with the Cisco 4500 series router.
This section describes how to configure the central site Cisco 4500 series router and the remote Cisco 765 series router for IP static routing with Challenge Handshake Authentication Protocol (CHAP) and Multilink Protocol (MLP).
Figure A-2 is an illustration of the configuration used in this example.
Following is the command summary to configure the remote Cisco 765 series router for IP static routing with CHAP and MLP:
set switch 5ess set system 765 set multidestination on set ppp multilink on set ppp authentication incoming chap set ppp authentication outgoing chap cd lan set ip address 192.168.147.9 set ip netmask 255.255.255.248 set ip routing on set ip rip update periodic cd set user 4500 set ppp clientname <765> set ppp secret client <765> set ip address 172.16.125.7 set ip netmask 255.255.255.0 set ip routing on set ip framing none set ip route destination 0.0.0.0 ga 172.16.125.1 propagate on set number 5558011 set bridging off set ip rip update off set ppp secret host <4500> set timeout 360 demand 2 threshold 32 duration 5 set active reboot
For detailed information regarding the commands listed here, refer to the related chapter in this publication.
Following is the command summary for configuring the central site Cisco 4500 series router for IP static routing with CHAP and MLP:
configure terminal hostname 4500 enable password lab username 4500 password 4500 username 765 password 765 isdn switch-type primary-5ess controller T1 0 framing esf linecode b8zs pri-group timeslots 1-24 interface Ethernet0 ip address 172.18.124.2 255.255.255.0 no shutdown interface Serial0:23 description This is pri-5ess 555-3693 ip address 172.16.125.1 255.255.255.0 encapsulation ppp dialer idle-timeout 360 dialer wait-for-carrier-time 60 dialer map ip 172.16.125.7 name 765 5553693 dialer-group 1 ppp authentication chap ppp multilink dialer load 125 no shutdown router eigrp 100 redistribute static network 172.18.124.0 ip host c765 172.16.125.7 ip host c7000 172.18.124.1 ip route 192.168.147.8 255.255.255.248 172.16.125.7 dialer-list 1 protocol ip permit line vty 0 4 password telnet login end
For detailed information regarding the commands listed here, refer to the Cisco 4500 series router publications.
This section describes how to configure the central site Cisco 4500 series router and the remote Cisco 765 series router for Internet Protocol (IP) static routing with Password Authentication Protocol (PAP) authentication.
Figure A-3 is an illustration of the configuration used in this example.
Following is the command summary to configure the remote Cisco 765 series router for IP static routing with PAP authentication:
set switch 5ess set system 765 set multidestination on set ppp multi on set ppp authentication in pap set ppp authentication out pap cd lan set ip address 192.168.147.9 set ip netmask 255.255.255.248 set ip routing on set ip rip update periodic cd set user 4500 set ip address 172.16.125.7 set ip netmask 255.255.255.0 set ip routing on set ip framing none set ppp clientname 765 set ppp password client <765> set ppp password host <765> set ip route destination 0.0.0.0 ga 172.16.125.1 propagate on set number 5558011 set bridging off set timeout 360 set active reboot
For detailed information regarding the commands listed here, refer to the related chapter in this publication.
Following is the command summary for configuring the central site Cisco 4500 series router for IP static routing with PAP authentication:
configure terminal hostname 4500 enable password lab username 4500 password 4500 username 765 password 765 isdn switch-type primary-5ess controller T1 0 framing esf linecode b8zs pri-group timeslots 1-24 interface Ethernet0 ip address 172.18.124.2 255.255.255.0 no shutdown interface Serial0:23 description This is pri-5ess 555-3693 ip address 172.16.125.1 255.255.255.0 encapsulation ppp dialer idle-timeout 360 dialer wait-for-carrier-time 60 dialer map ip 172.16.125.7 name 765 5553693 dialer-group 1 ppp authentication pap no shutdown router eigrp 100 redistribute static network 172.18.124.0 ip host c765 172.16.125.7 ip route 192.168.147.8 255.255.255.248 172.16.125.7 dialer-list 1 protocol ip permit line vty 0 4 password telnet login end
For detailed information regarding the commands listed here, refer to the Cisco 4500 series router publications.
This section describes how to configure the central site Cisco 4500 series router and the remote Cisco 765 series router for Internet Protocol (IP) unnumbered routing with Challenge Handshake Authentication Protocol (CHAP) authentication and Multilink Protocol (MLP).
Figure A-4 is an illustration of the configuration used in this example.
Following is the command summary for configuring the remote Cisco 765 series router for IP unnumbered routing with CHAP authentication and MLP:
For detailed information regarding the commands listed here, refer to the related chapter in this publication.
Following is the command summary for configuring the central site Cisco 4500 series router for IP unnumbered routing with CHAP authentication and MLP:
configure terminal hostname 4500 enable password lab username 4500 password 4500 username 765 password 765 isdn switch-type primary-5ess controller T1 0 framing esf linecode b8zs pri-group timeslots 1-24 interface Ethernet0 ip address 172.18.124.2 255.255.255.0 no shutdown interface Serial0:23 description This is pri-5ess 555-3693 ip unnumbered ethernet0 encapsulation ppp dialer idle-timeout 360 dialer wait-for-carrier-time 60 dialer map ip 192.168.147.9 name 765 5553693 dialer-group 1 ppp authentication chap ppp multilink dialer load 125 no shutdown router eigrp 100 redistribute static network 172.18.124.0 ip host c765 192.168.147.9 ip route 192.168.147.8 255.255.255.248 192.168.147.9 ip route 192.168.147.9 255.255.255.255 s0:23 dialer-list 1 protocol ip permit line vty 0 4 password telnet login end
For detailed information regarding the commands listed here, refer to the Cisco 4500 series router publications.
This section describes how to configure the central site Cisco 4500 series router and Cisco 765 series router for Internet Protocol (IP) static and Internetwork Packet Exchange (IPX) static routing with Point-to-Point Protocol (PPP) using CHAP and MLP.
Figure A-5 is an illustration of the configuration used in this example.
Following is the command summary to configure the remote Cisco 765 series router for IP static and IPX static routing with PPP using CHAP and MLP:
set switch 5ess set system 765 set multidestination on set ppp authentication incoming chap set ppp authentication outgoing chap cd lan set ipx network 1478 set ipx framing 802.2 set ipx routing on set ipx rip update periodic set ip address 192.168.147.9 set ip netmask 255.255.255.248 set ip routing on set ip rip update periodic cd set user 4500 set ipx network 32125 set ipx routing on set ipx route destination 3039e670 gateway 32125:0c08af65 set ipx service name CORP_FS1 type 4 address 3039e670:01:0451 set ipx spoof 10 set ipx rip update off set ipx framing none set ip address 172.16.125.7 set ip netmask 255.255.255.0 set ip routing on set ip framing none set encapsulation ppp set ip route destination 0.0.0.0 ga 172.16.125.1 propagate on set number 5558011 set bridging off set ip rip update off set timeout 360 set ppp secret host <4500> set ppp secret client <765> set ppp clientname 765 set active reboot
For detailed information regarding the commands listed here, refer to the related chapter in this publication.
Following is the command summary to configure the central site Cisco 4500 series router for IP static and IPX static routing with PPP:
configure terminal hostname 4500 enable password lab username 4500 password 4500 username 765 password 765 ipx routing isdn switch-type primary-5ess controller T1 0 framing esf linecode b8zs pri-group timeslots 1-24 interface Ethernet0 ip address 172.18.124.2 255.255.255.0 ipx network 48124 encapsulation sap no mop enabled no shutdown interface Serial0:23 description This is pri-5ess 555-3693 ipx network 32125 ip address 172.16.125.1 255.255.255.0 no ipx route-cache ipx watchdog-spoof encapsulation ppp ppp multilink ppp authentication chap dialer idle-timeout 360 dialer wait-for-carrier-time 60 dialer map ipx 32125.0040.f902.cf5d name 765 5553693 dialer map ip 172.16.125.7 name 765 5553693 dialer-group 1 no shutdown ipx route 1478 32125.0040.f902.cf5d ipx router rip no network 32125 redistribute static router eigrp 100 redistribute static network 172.18.124.0 ip host c765 172.16.125.7 ip route 192.168.147.8 255.255.255.248 172.16.125.7 dialer-list 1 protocol ipx permit dialer-list 1 protocol ip permit end
For detailed information regarding the commands listed here, refer to the Cisco 4500 series router publications.
This section describes how to configure the remote Cisco 765 series router and the central site Cisco 4500 series router for Internetwork Packet Exchange (IPX) static routing with Point-to-Point Protocol (PPP).
Figure A-6 is an illustration of the configuration used in this example.
Following is the command summary for configuring the remote Cisco 765 series router for IPX static routing with PPP:
set switch 5ess set system 765 set multidestination on set multilink on cd lan set ipx network 1478 set ipx framing 802.2 set ipx routing on set ipx rip update periodic cd set user 4500 set ppp clientname 765 set ppp secret client <765> set ipx network 32125 set ipx routing on set ipx route destination 3039e670 gateway 32125:0c08af65 set ipx service name CORP_FS1 type 4 address 3039e670:01:0451 set ipx spoofing 10 set ipx rip update off set ipx framing none set encapsulation ppp set number 5558011 set bridging off set timeout 360 set active reboot
For detailed information regarding the commands listed here, refer to the related chapter in this publication.
Following is the command summary for configuring the central site Cisco 4500 series router for IPX static routing with PPP:
configure terminal hostname 4500 enable password lab username 765 no ip routing ipx routing isdn switch-type primary-5ess controller T1 0 framing esf linecode b8zs pri-group timeslots 1-24 interface Ethernet0 ipx network 23160 encapsulation sap no mop enabled no shutdown interface Serial0:23 description This is pri-5ess 555-3693 no ipx route-cache ipx watchdog-spoof encapsulation ppp ppp multilink dialer idle-timeout 360 dialer wait-for-carrier-time 60 dialer map ipx 32125.0040.f902.cf5d name 765 5553693 dialer-group 1 ipx network 32125 no shutdown ipx route 1478 32125.0040.f902.cf5d ipx router rip no network 32125 redistribute static dialer-list 1 protocol ipx permit end
For detailed information regarding the commands listed here, refer to the Cisco 4500 series router publications.
Cisco 700 series routers implement multilink PPP, which is available in Release 11.0(3) or later of the Cisco IOS. You can disable multilink PPP in the following two environments:
Use the set ppp multilink command at the system level to disable multilink PPP, as follows:
766> set ppp multilink off
Cisco 700 series routers implement RIP Versions 1 and 2 and demand RIP. These two proposed standards are not implemented in Cisco IOS software. If you are connecting your router to a router running Cisco IOS software, and you want to use dynamic routing protocol, you must configure Cisco 700 series routers for RIP Version 1 and disable demand RIP.
Use the set ip rip command as follows to set the dynamic routing to use RIP Version 1:
766> set ip rip version 1
Use the set ip rip update command as follows to disable demand RIP:
766> set ip rip update periodic
It is possible to bridge data over ISDN to and from Cisco ISDN routers. Depending on your network environment, this might be an ideal solution. Bridging offers configuration simplicity with few concerns regarding network address space limitations and unroutable protocols. Bridging also offers compatibility with other products that need to bridge.
When bridging, you do not have the same ISDN line control that routing access lists provide. When bridging protocols such as Novell IPX, AppleTalk, or NetBIOS, it is possible for the ISDN line to remain connected for long periods of time. This can result in high ISDN usage charges. If bridging is the only solution for your environment, we recommend monitoring the ISDN line connection.
Cisco IOS Release 11.1 and earlier limit the number of simultaneous ISDN bridge sessions to one per interface.
Prior to Cisco IOS Release 11.2 (half-bridging), the Cisco IOS must also be configured to the bridging protocol, not the router protocol.
|
|