|
|
Product Numbers: AS52-12-TA-V110, AS5248-V110, AS5248-V110-DC, AS5260-V110, AS5260-V110-DC
This document describes the AT commands and S register for the V.110 12-port modules. Each module includes onboard terminal adapters (TAs) that can terminate up to 12 V.110 bit-rate-adapted digital calls.
This document contains the following sections:
Keep in mind the following guidelines when entering AT commands:
This section describes commands that begin with an alphabetic (A to Z) character.
Sets the network rate to 19200 bps and immediately attempts to start framing. This command is used for back-to-back testing only.
Re-executes the last command.
Informs the card that commands are being sent to it.
Dials a telephone number to establish a connection. The D command must be the last command on the command line. The dial string can contain up to 98 characters; valid characters are the digits 0 to 9, the command option listed in Table 1, and # and * for tone dialing. The TA ignores invalid characters; dial strings longer than 98 characters return an error. For example, to dial the telephone number 1 617 555 1234, enter the following command:
D 16175551234
Table 1 lists command options.
| Command | Description |
|---|---|
| L | Redials the last telephone number. |
The D command without any options is used for back-to-back testing.
Disconnects from the remote system and hangs up the telephone line. Table 2 lists command options.
| Command | Description |
|---|---|
| H0 | Go on-hook. |
| H1 | Go off-hook. |
Identifies various information about the TA. Table 3 lists command options.
| Command | Description |
|---|---|
| I0 | Displays the four-digit module product code. |
| I1 | Runs a checksum on firmware ROM and displays the four-digit result. |
| I2 | Displays the versions of the boot code, firmware, and FPGA. |
| I3 | Displays the self-test status. |
Sets the TA to the connect state.
Configures the TA to send result and status codes, such as OK, BUSY, and RING, to your workstation. Table 4 lists command options.
Q0
| Command | Description |
|---|---|
| Q0 | Result codes enabled. |
| Q1 | Result codes disabled. |
Displays the contents of S register n (where n is a decimal number). Table 5 lists command options.
0 to 38
S0
| Command | Description |
|---|---|
| S2 | Escape character. |
| S7 | Wait time for carrier. |
| S12 | Escape character guard time (default 1 second). |
| S38 | Wait time after DTR asserted (default 50 seconds). |
Selects the result code format sent to your workstation. Table 6 lists command options.
V1
| Command | Description |
|---|---|
| V0 | Digit format. |
| V1 | Text format. |
Selects the extended result code format sent to your workstation. Table 7 lists command options.
The following commands also affect the result code format:
X1
| Command | Description |
|---|---|
| X0 | Displays the "CONNECT" message when a connection is established. |
| X1 | Displays the "CONNECT XXXX" message, where XXXX is the network speed. |
Resets the parameters to defaults, goes on-hook, and forces the module into the autobaud state.
This section describes commands that begin with a caret (^).
Loads a new image. DTR must be deasserted.
This section describes commands that begin with a dollar sign ($).
Sets the DTE speed, where n is one of the following speeds: 600, 1200, 2400, 4800, 9600, or 19200 bps.
This section describes commands that begin with percent (%).
Sets the line speed. Table 8 lists command options.
Same as the DTE speed determined by autobaud.
| Command | Description |
|---|---|
| %B2 | 600 bps |
| %B3 | 1200 bps |
| %B4 | 2400 bps |
| %B5 | 4800 bps |
| %B6 | 9600 bps |
| %B7 | 19200 bps |
Displays the TA firmware version. Table 9 lists command option.
| Command | Description |
|---|---|
| %V1 | Displays module type and version. |
This section describes the commands that begin with an ampersand (&).
Controls the Data Carrier Detect (DCD) signal level. Use this command if your workstation requires DCD to be off at certain times. Table 10 lists command options.
&C1
| Command | Description |
|---|---|
| &C0 | DCD is always on. |
| &C1 | DCD follows the state of carrier from the remote system and turns on after the connect message. |
Specifies the TA action to take when DTR transitions off. The on-to-off transition of DTR must last as long as the value specified in register S25. Positive transitions of DTR (off-to-on) within five seconds after disconnect are ignored. Table 11 lists command options.
&D3
| Command | Description |
|---|---|
| &D0 | Ignores DTR while in data mode. |
| &D1 | Enters the command state when detecting an on-to-off transition of DTR. |
| &D2 | Sets the TA on-hook when detecting an on-to-off transition of DTR. |
| &D3 | Sets the TA on-hook and resets when detecting an on-to-off transition of DTR and prepares the serial port to accept an AT command. Also restores the factory default settings. |
Restores the factory default configuration.
Display S register and option values.
Stores the active commands and S registers.
This section describes the commands that begin with a backslash (\).
Selects the hardware flow control method used in the serial port. Table 12 lists command options.
\Q3
| Command | Description |
|---|---|
| \Q0 | Disables flow control. |
| \Q1 | Receive flow control. |
| \Q2 | Transmit flow control. |
| \Q3 | Receive and transmit flow control. |
Specifies the time, in minutes, that the TA waits before hanging up when data is not sent or received. The inactivity timer is available only during normal link connections. \T0 disables the timer.
0 to 136 minutes
\T0 (disabled)
The TA saves configuration settings in S registers. Each register controls a single TA function or is bit-mapped to control several functions. This section describes commands to display and change register values. We recommend that, wherever possible, you use the following commands only to display register contents and use the AT command set to change register values.
Specifies the character used for the three-character escape code sequence. When the TA is in the connect state and receives the escape code sequence, it enters the command state. Register S12 sets the guard time that must be present before and after the escape code character.
0 to 255 (ASCII decimal)
43 (+)
Specifies the time that the TA waits to
0 to 255 seconds
60 (seconds)
Sets the minimum quiet time before and after the three-character escape code. The interval between characters in the escape code or remote access attention sequence must be less than this guard time.
In normal mode, register S12 sets the guard time that precedes and follows the attention character sequence. It should be set to the same value on both the originating and answering TAs.
0 to 255 (0.02-second increments)
50 (1 second)
Sets the amount idle time before the TA times outs.
0 to 255 (seconds)
20 (seconds)
Cisco Connection Online (CCO) is Cisco Systems' primary, real-time support channel. Maintenance customers and partners can self-register on CCO to obtain additional information and services.
Available 24 hours a day, 7 days a week, CCO provides a wealth of standard and value-added services to Cisco's customers and business partners. CCO services include product information, product documentation, software updates, release notes, technical tips, the Bug Navigator, configuration notes, brochures, descriptions of service offerings, and download access to public and authorized files.
CCO serves a wide variety of users through two interfaces that are updated and enhanced simultaneously: a character-based version and a multimedia version that resides on the World Wide Web (WWW). The character-based CCO supports Zmodem, Kermit, Xmodem, FTP, and Internet e-mail, and it is excellent for quick access to information over lower bandwidths. The WWW version of CCO provides richly formatted documents with photographs, figures, graphics, and video, as well as hyperlinks to related information.
You can access CCO in the following ways:
For a copy of CCO's Frequently Asked Questions (FAQ), contact cco-help@cisco.com. For additional information, contact cco-team@cisco.com.
78-4378-01
|
|