|
|
This appendix lists and describes system error messages for the LightStream 1010 Asynchronous Transfer Mode (ATM) switch. The system software sends these error messages to the console (and, optionally, to a logging server on another system) during operation. Not all system error messages indicate problems with your system. Some are purely informational, while others may help diagnose problems with communications lines, internal hardware, or the system software.
The system error message main section provides descriptions of error messages organized according to the particular system facility that produces the messages. The facilities sections appear in alphabetical order, and within each system facility section, messages are listed alphabetically by mnemonic. Each error message is followed by an explanation and a recommended action. System error messages appear only when the system remains operational.
Error message severity levels correspond to the keywords assigned by the logging global configuration commands that define where and at what level these messages appear. The default is to log messages to the console at the debugging level (7).
System error messages begin with a percent sign and are structured as follows:
%FACILITY-SEVERITY-MNEMONIC: Message-text
FACILITY is a code consisting of two or more uppercase letters that indicate the facility to which the message refers. A facility can be a hardware device, a protocol, or a module of the system software. Table B-1 lists the system facilities codes.
| Code | Facility |
|---|---|
| AIP | ATM Interface Processor |
| ALIGN | Memory optimization in reduced instruction-set computer (RISC) processor |
| APPN | Advanced Peer-to-Peer Networking |
| ARAP | Apple Remote Access Protocol |
| AT | AppleTalk |
| AAL5 | ATM adaptation layer 5 |
| ATMCORE | ATM core software |
| ATMSIG | ATM signaling |
| CI | Environment monitor |
| DS3E3SUNI | DS3/E3 drivers |
| BGP | Border Gateway Protocol |
| BRI | Integrated Services Digital Network (ISDN) Basic Rate Interface |
| BSC | Binary Synchronous Communications mode |
| BSTUN | Block serial tunneling |
| CBUS | ciscoBus controller |
| CCP | Point-to-Point Compression Control Protocol |
| CI | 75xx platform chassis interface |
| CIP FACILITY: | Channel Interface Processor |
| ADAPTER | Adapter processing |
| BSQ | Buffer status queue processing |
| CBUS_ATTN | ciscoBus controller statistics |
| CBUS_WRITE | ciscoBus controller write support |
| CCA | Channel card adapter |
| CLAW | Common Link Access for Workstations |
| CONFIG | Configuration processing |
| CTA | Channel transport architecture |
| DEBUGGER | Messages issued when nonrecoverable errors occur |
| DIAG | Diagnostic processing |
| DMA | Direct memory access |
| GET_DATA | Internal routine for allocating transfer elements |
| INT | Interrupt handler |
| IPC | Interprocess Communication |
| LOADER | Relocating loader |
| LOVE | CIP-to-router statistics |
| PNNI/IISP | PNNI or IISP routing |
| Miscellaneous | Miscellaneous error messages |
| OC3SUNI OC12SUNI | Optical carrier 3 driver Optical carrier12 driver |
| OIR | Online insertion and removal |
| SONICT | Ethernet driver |
| TBRIDGE | Transparent bridging |
| TCP | Transmission Control Protocol |
| TMQ | Inbound terminal port queuing |
| TN | Telnet |
| TR | Token Ring |
| TUN | Tunnel |
| UCODE | Microcode |
| UTIL | Utility |
| VINES | Banyan VINES |
| VIP | Versatile Interface Processor |
| X25 | X.25 |
| XNS | Xerox Network Systems |
SEVERITY is a single-digit code from 0 to 7 that reflects the severity of the condition. The lower the number, the more serious the situation. Table B-2 lists the severity levels.
| Level | Description |
|---|---|
| 0 - emergency | System unusable |
| 1 - alert | Immediate action needed |
| 2 - critical | Critical condition |
| 3 - error | Error condition |
| 4 - warning | Warning condition |
| 5 - notification | Normal but significant condition |
| 6 - informational | Informational message only |
| 7 - debugging | Appears during debugging only |
MNEMONIC is a code that uniquely identifies the error message.
Message-text is a text string describing the condition. This portion of the message sometimes contains detailed information about the event, including terminal port numbers, network addresses, or addresses that correspond to locations in the system memory address space. Because the information in these variable fields changes from message to message, it is represented here by short strings enclosed in square brackets ([ ]). A decimal number, for example, is represented as [dec]. Table B-3 lists the representations of variable fields and the type of information in them.
The following is a sample system error message:
%SONICT-3-XMIT_ERR: TX Error [hex]
| Representation | Type of Information |
|---|---|
| [dec] | Decimal number |
| [hex] | Hexadecimal number |
| [char] | Single character |
| [chars] | Character string |
| [v-name] | VINES name; or number (hex or decimal) |
Some messages describe internal errors and contain traceback information. This information is very important and should be included when you report a problem to your technical support representative.
The following sample message includes traceback information:
-Process= "Exec", level= 0, pid= 17LightStream 10101 ATM switch software error messages.
ATM adaptation layer 5 error messages.
Error Message %AAL5-3-INTERNAL_ERROR: atm_output: Bad enctypeExplanation ATM output error. Bad enctype.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %AAL5-3-INTERNAL_ERROR: aal5send: mmc_queuecell failedExplanation AAL5 send error. MMC queue cell failed.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %AAL5-3-INTERNAL_ERROR: Out of reassembly buffersExplanation Out of reassembly memory buffers error.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %AAL5-3-INTERNAL_ERROR: AAL5 doesn't handle such large pktsExplanation AAL5 does not handle such large packets error.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %AAL5-3-INTERNAL_ERROR: No more big aal5 pktsExplanation No more big AAL5 packets error.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %AAL5-3-RXERR: [hex], orig [hex], port= [chars]Explanation Origin port number error.
Recommended Action If this message occurs, contact your technical support representative for assistance.
ATM CORE software error messages.
Error Message %ATMCORE-3-INTERNAL_ERROR: nvgenCttRow: [dec] stable row, bad scExplanation Nonvolatile RAM generation connection traffic table row found with stable row and bad service category.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-2-INTERNAL_CRITICAL: rmPhyLogIf_2_ifId: Null logical RM cbExplanation Resource management physical and logical interface two interface ID error. Null logical resource management control block.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-2-INTERNAL_CRITICAL: rmPhyLogIf_2_ifId: Null swidb atm cbExplanation Resource management physical and logical interface two interface ID error. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-2-INTERNAL_CRITICAL: rmPhyLogIf_2_ifId: Null sw atm ifcbExplanation Resource management physical/logical interface to interface ID error. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-2-INTERNAL_CRITICAL: getIfPhyLogRmFromIfcb: Null sw atm ifcbExplanation Get interface physical and logical resource management control block from interface control block error. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-3-INTERNAL_ERROR: getIfPhyRmFromIfcb: bad output if cbsExplanation Get interface physical/logical resource management control block from interface control block error. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-3-INTERNAL_ERROR: isCpuIntf: bad if cbsExplanation CPU interface check error. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-2-INTERNAL_CRITICAL: createLogIfRm: Duplicate Logical interfaceExplanation Create logical interface resource management error. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-2-INTERNAL_CRITICAL: createLogIfRm: No Physical interfaceExplanation Create logical interface resource management error. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-2-INTERNAL_CRITICAL: createLogIfRm: No atmswdbExplanation Create logical interface resource management error. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-2-INTERNAL_CRITICAL: setPhyPortMaxCr: Bad plimtypeExplanation Set physical port maximum cell rate error. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-2-INTERNAL_CRITICAL: createPhyIfRm: atm_db is nullExplanation Create physical interface resource management error. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-2-INTERNAL_CRITICAL: createPhyIfRm: atmswdb is nullExplanation Create physical interface resource management error. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-2-INTERNAL_CRITICAL: createPhyIfRm: ifCb is nullExplanation Create physical interface resource management error. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-2-INTERNAL_CRITICAL: createPhyIfRm: ifRm not nullExplanation Create physical interface resource management error. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-2-INTERNAL_CRITICAL: createPhyIfRm: swidb is nullExplanation Create physical interface resource management error. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-2-INTERNAL_CRITICAL: atmcore_rm_if_init: Not ATM ifExplanation Resource management interface initialization error. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-2-INTERNAL_CRITICAL: atmcore_rmLogicalIntfCreated: No swidbExplanation Resource management logical interface creation error. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-2-INTERNAL_CRITICAL: atmcore_rmLogicalIntfCreated: No atm_swdbExplanation Resource management logical interface creation error. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-2-INTERNAL_CRITICAL: atmcore_rmLogicalIntfCreated: No ifCBExplanation Resource management logical interface creation error. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-2-INTERNAL_CRITICAL: atmcore_rmLogicalIntfCreated: Can't get rcv ctt rowExplanation Resource management logical interface creation error. Can't get receive connector traffic table row.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-2-INTERNAL_CRITICAL: atmcore_rmLogicalIntfCreated: Can't get xmt ctt rowExplanation Resource management logical interface creation error. Can't get transmit connector traffic table row.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-2-INTERNAL_CRITICAL: atmcore_rmLogicalIntfDeleted: No swatmdbExplanation Resource management logical interface deletion error. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-3-INTERNAL_ERROR: atmcore_rmGetDefaultQosObj: bad input trafficExplanation Resource management get default quality of service object error. Bad input.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-3-INTERNAL_ERROR: sc_to_trafficParmSc: bad Service CategoryExplanation Service category to traffic parameter service category error. Bad service category.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-3-INTERNAL_ERROR: show_if_conn_hw: no CTT rowExplanation Display interface hardware connection error. No control traffic table row.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-2-INTERNAL_CRITICAL: show_if_conn_hw: no ifCBExplanation Display interface hardware connection error. No interface control block.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-3-INTERNAL_ERROR: show_atm_int_rm: Cannot find phy if structureExplanation Display interface hardware connection error. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-3-INTERNAL_ERROR: show_atm_int_rm: Cannot find phylog if structureExplanation Display interface resource management error. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-3-INTERNAL_ERROR: printCttRow: [dec] rowindex, bad scExplanation Print connection traffic table error. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-2-INTERNAL_CRITICAL: atm_rm_show_commands null csbExplanation ATM resource management show command error. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-2-INTERNAL_CRITICAL: atm_rm_show_commands: bad csb show typeExplanation ATM resource management show command error. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-3-INTERNAL_ERROR: atmcore_rmCtt_init: Error allocating row [dec], error [dec]Explanation Resource management connection traffic table initialization error. Error allocating default at startup row.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-3-INTERNAL_ERROR: cfgCttCommands: can't release not-ready rowExplanation Configuring connection traffic table error. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-2-INTERNAL_CRITICAL: atm_rm_show_commands null csbExplanation ATM resource management show command error. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-3-INTERNAL_ERROR: atm_rm_cfg_commands: nvgen default: should not happenExplanation Errors detected in nonvolatile RAM generation of connection traffic table.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-3-INTERNAL_ERROR: atm_rm_cfg_commands: bad csb infoExplanation ATM resource management configuration command error. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-3-INTERNAL_ERROR: chg_phyif_qthresh_req: bad selectorExplanation Change physical interface queue threshold request error. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-3-INTERNAL_ERROR: nvgenParmLimits: bad parm limit selectorExplanation Nonvolatile RAM generation parameter limits error. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-3-INTERNAL_ERROR: nvgenParmLimits: bad parm limit service categoryExplanation Nonvolatile RAM generation parameter limits error. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-3-INTERNAL_ERROR: nvgenStartOutputQ: bad queue valueExplanation Nonvolatile RAM generation output queue error. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-3-INTERNAL_ERROR: nvgenStartServCatOutQ: bad service category valueExplanation Nonvolatile RAM generation start service category error. Bad service category selected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-3-INTERNAL_ERROR: nvgenTolerance: bad service category valueExplanation Nonvolatile RAM generation output queue. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-2-INTERNAL_CRITICAL: atm_rm_show_commands null csbExplanation ATM resource management show command error. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-3-INTERNAL_ERROR: atm_rm_int_cfg_commands: bad nvgen selector valueExplanation ATM resource management initialization configuration command error. Bad nonvolatile RAM generation value selected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-3-INTERNAL_ERROR: isOutputQosOk: Bad scExplanation Is output quality of service correct? Bad service category.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-3-INTERNAL_ERROR: isFlowPolicyOk: Bad scExplanation Is flow policy OK? Bad service category.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-3-INTERNAL_ERROR: serviceCategoriesOk: Bad scExplanation Are service categories correct? Bad service category.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-3-INTERNAL_ERROR: processIntfListConnResGetReq: Bad IfSelectExplanation Interface list connection reset get request error. Bad interface selection.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-3-INTERNAL_ERROR: processIgnoreRcacReq: more than 1 intfExplanation Resource call admission control request error. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-3-INTERNAL_ERROR: processIgnoreRcacReq: no intf structureExplanation Resource call admission control request error. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-3-INTERNAL_ERROR: processIgnoreRcacReq: bad scExplanation Resource call admission control request error. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-2-INTERNAL_CRITICAL: atmcore_rmRcacGetIntfConnRes: Null re/rsp pointerExplanation Resource management resource call admission control get interface connection resource. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-2-INTERNAL_CRITICAL: atmcore_rmRcacRelIntfConnRes: Null req pointerExplanation Resource management resource call admission control get interface connection resource. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-2-INTERNAL_CRITICAL: atmcore_rmRcacRelIntfConnRes: Null req pointerExplanation Resource management resource call admission control get interface connection resource. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-2-INTERNAL_CRITICAL: atmcore_rmRcacRelIntfConnRes: Bad scExplanation Resource management resource call admission control get interface connection resource. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-2-INTERNAL_CRITICAL: atmcore_rmRcacRelIntfConnRes: Bad interfaceExplanation Resource management resource call admission control release interface connection resource. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-3-INTERNAL_ERROR: atmcore_rmRcacAreTrafficParmConsistent: No ctt rowExplanation Resource management resource call admission control, are traffic parameters consistent. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-3-INTERNAL_ERROR: atmcore_rmRcacRelIntfConnRes: Bad interfaceExplanation Resource management resource call admission control release connection reset. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-3-INTERNAL_ERROR: allocNewStableRow: dup rowExplanation Allocate new stable row error. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-3-INTERNAL_ERROR: allocNewTransientRow: dup rowExplanation Allocate new transient row error. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-3-INTERNAL_ERROR: trafficIsCompCon: bad scExplanation Traffic is not compatible to the connection error. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-2-INTERNAL_CRITICAL: atmcore_rmCtt_init: no chunk for Stable CTTExplanation Resource management connection traffic table error. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-2-INTERNAL_CRITICAL: atmcore_rmCtt_init: no chunk for Transient CTTExplanation Resource management connection traffic table initialization error. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-3-INTERNAL_ERROR: atmcore_rmCtt_init: Error allocating row 1Explanation Resource management connection traffic table initialization error. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-2-INTERNAL_CRITICAL: atmcore_rmCttStableRowAlloc: null request pointerExplanation Resource management connection traffic table stable row allocation error. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-3-INTERNAL_ERROR: atmcore_rmCttStableRowAlloc: Bad parm qualsExplanation Resource management connection traffic table stable row allocation error. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-3-INTERNAL_ERROR: atmcore_rmCttRowGet: No SVC rowExplanation Resource management connection traffic table row get request error. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-2-INTERNAL_CRITICAL: rmTransientCttRowAct: null request pointerExplanation Resource management transient connection traffic table row acknowledgment. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-3-INTERNAL_ERROR: atmcore_rmCttRowDetach: num Vxs attached <= 0Explanation Resource management connection traffic table row detach request error. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-3-INTERNAL_ERROR: atmcore_rmCttAreFlowsSame: sc differentExplanation Resource management connection traffic table are flows the same error. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-3-INTERNAL_ERROR: atmcore_rmCttAreFlowsSame: bad scExplanation Resource management connection traffic table are flows the same error. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-2-INTERNAL_CRITICAL: rmCtt_chkDeleteRow: row to delete not foundExplanation Resource management connection traffic table check row deletion error. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-3-INTERNAL_ERROR: atmcore_rmPhyIfOutQScThreshCfg: can't install if abr threshExplanation <explanation>.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-3-INTERNAL_ERROR: rm_changeAllIfAbrRrThresh: Null phy RM cbExplanation Resource management change all available bit rate interface request threshold. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-3-INTERNAL_ERROR: rm_switchChangeCellPriorityLimit: Couldn't install hwExplanation Resource management change cell loss priority limit error. Hardware error occurred.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-3-INTERNAL_ERROR: atmcore_rmGlobalCfg: bad selectorExplanation Resource management global configuration error. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-2-INTERNAL_CRITICAL: checkChangePortMetrics: No ifRmExplanation Check change port matrix error. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-3-INTERNAL_ERROR: atmcore_rmPhyIfOutQCfg: Couldn't install hwExplanation Resource management physical interface output queue configuration error. Could not install hardware.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-3-INTERNAL_ERROR: atmcore_rmPhyIfOutQScThreshCfg: bad selectorExplanation Resource management physical interface output queue service category threshold configuration error. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-3-INTERNAL_ERROR: atmcore_rmPhyIfOutQScThreshCfg: can't install if abr threshExplanation Resource management physical interface output queue service category threshold configuration error. Cannot install if available bit rate interface threshold in hardware.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-3-INTERNAL_ERROR: atmcore_rmPhyIfOutQScThreshCfg: bad selectorExplanation Resource management physical interface output queue service category threshold configuration error. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-3-INTERNAL_ERROR: atmcore_rmPhyIfClsFlowCfg: bad selectorExplanation Resource management physical interface cells flow configuration error. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-3-INTERNAL_ERROR: atmcore_rmIfTrParmLimitCfg: bad selector.Explanation Resource management physical interface traffic parameter limit configuration. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-3-INTERNAL_ERROR: deriveTrafTypeFromOid: no OID ptrExplanation Derive traffic type from object ID error. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-3-INTERNAL_ERROR: k_atmTrafficDescrParamEntry_set: Bad rowStatus valueExplanation ATM traffic description parameter entry configuration error. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-2-INTERNAL_CRITICAL: setPhyIfStaticMetrics: Bad port typeExplanation A set physical interface static metrics error. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-2-INTERNAL_CRITICAL: initPhyIfPlatDepRmValues: Bad plim typeExplanation Initialize physical interface platform dependent resource management values error. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-2-INTERNAL_CRITICAL: getDefaultPhyIfOutQMaxSize: Bad queueExplanation Get default physical interface output queue maximum size error. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-2-INTERNAL_CRITICAL: initPhyIfPlatDepRmValues: Bad queue.Explanation <explanation>.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-2-INTERNAL_CRITICAL: rmInstallInterfaceHardware: Can't install CPU Max q sizeExplanation Initial physical interface platform dependent resource management values error. Hardware error.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-2-INTERNAL_CRITICAL: rmInstallInterfaceHardware: Can't install Max q sizeExplanation Resource management installation interface hardware error. Cannot install maximum queue size.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-3-INTERNAL_ERROR: rmInstallInterfaceHardware: can't install if abr thres.Explanation Resource management installation interface hardware error. Cannot install interface available bit rate threshold.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-2-INTERNAL_CRITICAL: rmInstallInterfaceHardware: Missing RM idb pointerExplanation Resource management installation interface hardware error. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-2-INTERNAL_CRITICAL: rmInstallSwitchHardware: Can't install pri cell limitExplanation Resource management switch hardware installation error. Cannot install priority limit.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-3-INTERNAL_ERROR: selectTrafficValue: Bad traffic parmExplanation Select traffic value error. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-3-INTERNAL_ERROR: selectTraffic: Bad scExplanation Select traffic value error. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-3-INTERNAL_ERROR: outputQosValueOk: Bad MetricAttrExplanation Output queue quality of service value error. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-3-INTERNAL_ERROR: accumulateOutputQosMetric: Bad scExplanation Accumulate output quality of service metric error. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-2-INTERNAL_CRITICAL: trafficCompleteConsistent: Bad scExplanation Traffic complete and consistent error. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-2-INTERNAL_CRITICAL: flowTrafficParmLimitsOk: Bad scExplanation Traffic flow parameter limits error. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-2-INTERNAL_CRITICAL: canAdmitP2mpFlow: Bad flowExplanation Can admit point to multipoint flow error. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-2-INTERNAL_CRITICAL: canAdmitTraffic: Bad scExplanation Can admit point to multipoint flow error. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-3-INTERNAL_ERROR: allocFlowEbw: Bad scExplanation Allocate flow Ebw error. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-3-INTERNAL_ERROR: relFlowEbw: Bad scExplanation Release flow Ebw error. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-3-INTERNAL_ERROR: rm_changeConnHalfLeg: no CTT rowExplanation Resource management change connected half leg error. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-2-INTERNAL_CRITICAL: rm_backgroundChangeIntfConnParm: no ifCBExplanation Resource management background change interface connection parameter error. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-3-INTERNAL_ERROR: rm_backgroundChangeIntfParm: No phy if am cbExplanation Resource management background change interface connection parameter error. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-3-INTERNAL_ERROR: derivePifIM: Bad If typeExplanation Derive PifIM error. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-3-INTERNAL_ERROR: ls1010_atmcore_rmInstallIfPacing: Can't install port pacingExplanation Resource management interface installation pacing error. Cannot install port pacing.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-3-INTERNAL_ERROR: convertRowScToSnmpFmt: Bad scExplanation Convert service category row to SNMP format error. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-3-INTERNAL_ERROR: sameTrafficParms: Bad scExplanation Same traffic parameters error. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-3-INTERNAL_ERROR: convertIntToExtRowData: Bad scExplanation Convert interface to extract row data. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-3-INTERNAL_ERROR: ls1010_atmcore_rmGetTransmitOutputQueue: Bad scExplanation Resource management get transmit output queue error. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-3-INTERNAL_ERROR: ls1010_atmcore_rmIsFeatureCardQHiPri: Bad scExplanation Resource management is feature card high priority error. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-2-INTERNAL_CRITICAL: fetchPhyIfI: Bad port typeExplanation Fetch physical interface error. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-2-INTERNAL_CRITICAL: ls1010_atmcore_rmGetInputUpcParms: Null input ptrsExplanation Resource management get input usage parameter control parameter error. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-3-INTERNAL_ERROR: ls1010_atmcore_rmGetInputUpcParms: bit rate too largeExplanation Resource management get input usage parameter control parameter error. Bit rate too set too high.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-3-INTERNAL_ERROR: ls1010_atmcore_rmGetInputUpcParms: no if log rm cbExplanation Resource management get input usage parameter control parameter error. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-3-INTERNAL_ERROR: ls1010_atmcore_rmGetInputUpcParms: no if phy rm cbExplanation Resource management get input usage parameter control parameter error. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-3-INTERNAL_ERROR: ls1010_atmcore_rmGetTransmitQueueThresh: bad inputExplanation Resource management get transmit queue threshold error. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-3-INTERNAL_ERROR: ls1010_atmcore_rmGetTransmitQueueThresh: bad output if cbsExplanation Resource management get transmit queue threshold error.A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-3-INTERNAL_ERROR: ls1010_atmcore_rmConnGetFeatCardTxQThresholds: bad inputExplanation Resource management connection get feature card transmit queue threshold error. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMCORE-3-INTERNAL_ERROR: ls1010_atmcore_rmConnGetFeatCardTxQThresholds: bad output if cbsExplanation Resource management connection get feature card transmit queue threshold error. A data structure inconsistency was detected.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Explanation ATM signal control block is not found for an input message.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMSIG-3-NOSVC: no SVC, atmSig_findPartyBlockByRefExplanation ATM signal control block is not found for a party message.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMSIG-3-NOMEM: [chars]Explanation ATM signaling could not allocate memory.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMSIG-3-FAILASSERT: [chars]Explanation ATM signaling finds an internal critical error.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMSIG-3-FAILHALFLEGREM: 2nd halfleg failed, Get 2nd half leg failure. no ifcbExplanation ATM signaling failed to remove the second half-leg of a connection.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMSIG-3-FAILHALFLEGREM: halfLeg removal failed, removeHalfLegExplanation ATM signaling failed half-leg removal error.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMSIG-3-INVPNNIMSG: Invalid msg from routing/pnni: NULL port_rsp messageExplanation Invalid massage received from routing. Null message.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMSIG-3-INVPNNIMSG: Invalid msg from routing/pnni: msg vers badExplanation Invalid massage received from routing. Message version bad.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMSIG-3-INVPNNIMSG: Invalid msg from routing/pnni: msg code not respExplanation Invalid massage received from routing. Message code not responding.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMSIG-3-INVPNNIMSG: Invalid msg from routing/pnni: NULL SVCExplanation Invalid massage received from routing. No signaling control block.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMSIG-3-INVPNNIMSG: Invalid msg from routing/pnni: NULL curr partyExplanation Invalid massage received from routing. Null current party.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMSIG-3-INVPNNIMSG: Invalid msg from routing/pnni: dest proc not validExplanation Invalid massage received from routing. Destination process not valid. It must be a signaling module.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMSIG-3-INVPNNIMSG: Invalid msg from routing/pnni: source proc not validExplanation Invalid massage received from routing. Source process not valid. It must be a routing module.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMSIG-3-INVPNNIMSG: Invalid msg from routing/pnni: msg type not validExplanation Invalid massage received from routing. Message type not valid.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMSIG-3-INVPNNIMSG: Invalid msg from routing/pnni: NULL messageExplanation Invalid massage received from PNNI routing error. Null message received.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMSIG-3-INVPNNIMSG: Invalid msg from routing/pnni: NULL port listExplanation Invalid massage received from routing. No ports can be found to route this call.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMSIG-3-INVPNNIMSG: Invalid msg from routing/pnni: number of ports > MAXExplanation Invalid massage received from routing. Number of ports greater than maximum.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %ATMSIG-3-INVPNNIMSG : Invalid msg from routing/pnni : error return code No memory atmsys_get_buf for next_port_req No memory atmsys_get_buf for source_route_req No buffer for sending Setup message No buffer for sending Call Proceeding message No buffer for sending Connect message No buffer for sending Connect Ack message No buffer for sending Release message No buffer for sending Release Comp message No buffer for sending Status message No buffer for sending Status Enquiry message No buffer for sending Restart message No buffer for sending Restart Ack message No buffer for xfer Setup message No buffer for sending Connect message No buffer for sending Add Party message No buffer for sending Status message No buffer for sending AddPartyAck message No buffer for sending AddPartyRej message No buffer for sending DropParty message No buffer for sending DropPartyAck message No buffer for sending Begin Pdu No buffer for sending Begin Ack Pdu No buffer for sending Begin Rej Pdu No buffer for sending End Pdu No buffer for sending End Ack Pdu No buffer for sending Resync Pdu No buffer for sending Resync Ack Pdu No buffer for sending Ustat Pdu No buffer for sending Stat Pdu No buffer for sending Poll PduExplanation <explanation>.
Recommended Action If this message recurs, contact your technical support representative for assistance.
Environment monitor error messages.
Error Message %CI-3-TEMP: Temperature overheatExplanation System temperature overheat error.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %CI-6-TEMPOK: Temperature OKExplanation System temperature has no error.
Recommended Action This message is provided for information only.
Error Message %CI-3-BLOWER: Fan failureExplanation System Fan failure error.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %CI-6-BLOWEROK: Fan OKExplanation System fan has no error.
Recommended Action This message is provided for information only.
Error Message %CI-3-PSFAIL: Power supply [dec] failureExplanation System power supply number failure error.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %CI-3-PSOK: Power supply [dec] OKExplanation System power supply number has no error.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %CI-6-PSCHANGE: Power supply [dec] changed from [chars] [chars] to [chars]Explanation Power supply status has changed error.
Recommended Action This message is provided for information only.
DS3E3SUNI driver error messages.
Error Message %DS3E3SUNI-1-NOMEMORY: Unit [dec], no memory for [chars] IDB structureExplanation The unit described has a memory error for the IDB structure.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %DS3E3SUNI-1-NOMEMORY: Unit [dec], no memory for [chars] ds structureExplanation The unit described has a memory error for the digital system structure.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Explanation The ASP Feature Card, Version II, will only work with IOS Version 11.2 or later software.
Recommended Action Update your LightStream 1010 IOS software to Version 11.2 or later.
Error Message %RSP-3-IDPROM: Bad or missing ID EEPROM, controller type [dec]Explanation A bad or missing ID EEPROM error occurred on the controller type described.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %RSP-2-NOMEMORY: No memory available for OIR processExplanation No memory is available to allow hot-swapping to store the current PAM interface configuration.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %LINK-3-TOOBIG: Interface [chars] Output packet size of [dec] bytes too bigExplanation Interface output packet has too many bytes.
Recommended Action If this message occurs, contact your technical support representative for assistance.
OC3SUNI and OC12SUNI driver error messages.
Error Message %OC3SUNI-1-NOMEMORY: Unit [dec], no memory for [chars] IDB structureExplanation The unit described has a memory error for the IDB structure.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %OC3SUNI-1-NOMEMORY: Unit [dec], no memory for [chars] ds structureExplanation The unit described has a memory error for the ds structure.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %OC12SUNI-1-NOMEMORY: Unit [dec], no memory for [chars] IDB structureExplanation The unit described has a memory error for the interface data block structure.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %OC12SUNI-1-NOMEMORY: Unit [dec], no memory for [chars] ds structureExplanation The unit described has a memory error for the ds structure.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Online insertion and removal error messages.
Error Message %OIR-3-SHUTDOWN: Shutting down due to overheatExplanation System shutdown due to overheat error.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %OIR-6-INSCARD: Card inserted in slot [dec], subcard [dec], interfaces administratively shutdownExplanation Card inserted in the slot, sub card, port, and interfaces described has been administratively shutdown.
Recommended Action This message is provided for information only.
Error Message %OIR-6-REMCARD: Card removed from slot [dec], subcard [dec], interfaces disabledExplanation Card inserted in the slot, sub card, port, and interfaces described has been disabled.
Recommended Action This message is provided for information only.
Error Message %OIR-3-LONGSTALL: Long bus stall ([dec] [chars]), the new PAM may not seated properly. Please remove it and try again.Explanation While hot-swapping a PAM the system has detected the card is not seated properly.
Recommended Action Remove the card and reinsert it.
PNNI and IISP routing error messages.
Error Message %PNNI-4-INTERNAL_ERROR: IISP failed to get the argument to iisp_router processExplanation An internal software error has occurred.
Recommended Action If this message recurs, contact your technical support representative for assistance.
Error Message %PNNI-4-BADPACKET: Invalid pkt: length shorter than header size [dec], phdr->lengthExplanation Unrecognized type of PNNI packet has been received.
Recommended Action Check the sender of the packet for any possible problem.
Error Message %PNNI-4-BADPACKET: Invalid pkt: unrecognized packet type [dec], TLV_TYPE( phdr )Explanation Unrecognized type of PNNI packet has been received.
Recommended Action Check the sender of the packet for any possible problem.
Error Message %PNNI-4-INTERNAL_ERROR: PNNI failed to get the argument to pnni_router processExplanation An internal software error has occurred.
Recommended Action If this message recurs, contact your technical support representative for assistance.
Error Message %PNNI-4-INTERNAL_ERROR: PNNI failed to set the argument to pnni_router processExplanation An internal software error has occurred.
Recommended Action If this message recurs, contact your technical support representative for assistance.
Error Message %PNNI-4-INTERNAL_ERROR: PNNI failed to set the argument to pnni_update processExplanation An internal software error has occurred.
Recommended Action If this message recurs, contact your technical support representative for assistance.
Error Message %PNNI-4-ADDRESS_EXIST: Address derived from the switch's prefix by soft PVC manager [chars] clashes with existing address in prefix tableExplanation Automatic soft PVC port address assignment fails. Address derived from the switch's prefix for soft PVC port clashes with an existing address in the prefix table.
Recommended Action If possible, assign a new MAC address to the end system that causes the clash.
Error Message %PNNI-4-ATM_SYS_ERROR: Error: Incorrect API version. Mismatched API message version received by PNNIExplanation An internal software error has occurred.
Recommended Action If this message recurs, contact your technical support representative for assistance.
Error Message %PNNI-4-INTERNAL_ERROR: Cannot add NNI interface. An attempt to add an NNI interface failedExplanation An internal software error has occurred.
Recommended Action If this message recurs, contact your technical support representative for assistance.
Error Message %PNNI-4-INTERNAL_ERROR: Received API message to create an interface for an existing portExplanation An internal software error has occurred.
Recommended Action If this message recurs, contact your technical support representative for assistance.
Error Message %PNNI-4-INTERNAL_ERROR:Received API message to delete an interface that PNNI does not know ofExplanation An internal software error has occurred.
Recommended Action If this message recurs, contact your technical support representative for assistance.
Error Message %PNNI-4-ATM_SYS_ERROR: Error: Received Unrecognized API messageExplanation An internal software error has occurred.
Recommended Action If this message recurs, contact your technical support representative for assistance.
Error Message %PNNI-4-INTERNAL_ERROR: Unrecognized req msg from signaling [hex]Explanation Unrecognized request message from signaling error process.
Recommended Action If this message recurs, contact your technical support representative for assistance.
Error Message %PNNI-4-BADPACKET: Invalid REQ pkt: [chars] [dec] [dec]Explanation Invalid PNNI request packet has been received.
Recommended Action Check the sender of the packet for any possible problem.
Error Message %PNNI-4-BADPACKET: Invalid DS pkt: Type in header is not Nodal PTSE summaries (512), type [dec]Explanation Invalid PNNI database summary packet has been received.
Recommended Action Check the sender of the packet for any possible problem.
Error Message %PNNI-4-BADPACKET: Invalid DS pkt: Length in hdr shorter than smallest possible, len [dec], ds_data->lengthExplanation Invalid PNNI database summary packet has been received.
Recommended Action Check the sender of the packet for any possible problem.
Error Message %PNNI-4-BADPACKET: Invalid DS pkt: Bad length in node [chars], eDS PTSE sum len [dec], left [dec], count [dec], left [dec]Explanation Invalid PNNI database summary packet has been received.
Recommended Action Check the sender of the packet for any possible problem.
Error Message %PNNI-4-INTERNAL_ERROR: NULL node in ptsedb ID [hex]Explanation Invalid PNNI database summary packet has been received.
Recommended Action Check the sender of the packet for any possible problem.
Error Message %PNNI-4-INTERNAL_ERROR: Rev DS in an invalid nbr stateExplanation Invalid neighbor state found.
Recommended Action If this message recurs, contact your technical support representative for assistance.
Error Message %PNNI-4-INTERNAL_ERROR: Remove neighbor with interface list not emptyExplanation A neighbor is being removed but interface list still shows some interface.
Recommended Action If this message recurs, contact your technical support representative for assistance.
Error Message %PNNI-4-INTERNAL_ERROR: Cannot locate neighbor to be deletedExplanation Cannot locate a neighbor to be deleted.
Recommended Action If this message recurs, contact your technical support representative for assistance.
Error Message %PNNI-4-INTERNAL_ERROR: Internal Nbr Number Stack OverflowExplanation An internal software error has occurred.
Recommended Action If this message recurs, contact your technical support representative for assistance.
Error Message %PNNI-4-CONFIG_ERROR: Configuration Error: Port looped-back, cannot form adjacencyExplanation PNNI detects a port looped back to itself.
Recommended Action Check the sender of the packet for a possible problem.
Error Message %PNNI-4-BADPACKET: Invalid ACK pkt: [chars]Explanation Invalid ACK packet has been received.
Recommended Action Check the sender of the packet for a possible problem.
Error Message %PNNI-4-INTERNAL_ERROR: rxmt timer with no elementExplanation Invalid ACK packet has been received.
Recommended Action Check the sender of the packet for a possible problem.
Error Message %PNNI-4-BADPACKET: Invalid PTSP pkt: Bad Type in PTSE header: [dec]Explanation Invalid ACK packet has been received.
Recommended Action Check the sender of the packet for a possible problem.
Error Message %PNNI-4-BADPACKET: Invalid PTSP pkt: Unknown type in PTSE header: [dec],)Explanation Invalid PTSP packet has been received.
Recommended Action Check the sender of the packet for a possible problem.
Error Message %PNNI-4-BADPACKET: Invalid PTSP pkt: Inconsistent type between PTSE header and: PTSE content [dec] [dec]Explanation Invalid PTSP packet has been received.
Recommended Action Check the sender of the packet for a possible problem.
Error Message %PNNI-4-BADPACKET: Invalid PTSP pkt: PTSE len does not add up to total PTSE len in header [dec] [dec]Explanation Invalid PTSP packet has been received.
Recommended Action Check the sender of the packet for a possible problem.
Error Message %PNNI-4-BADPACKET: Invalid PTSP pkt: IG with type matching the PTSE type is missing: from PTSE [dec] [dec]Explanation There is no information group inside this PTSE that has the same type as the type in the PTSE header.
Recommended Action Check the sender of the packet for a possible problem.
Error Message %PNNI-4-BADPACKET: Invalid PTSP pkt: Bad checksum in PTSE ID: [dec]Explanation Invalid PTSP packet has been received.
Recommended Action Check the sender of the packet for a possible problem.
Error Message %PNNI-4-BADPACKET: Invalid PTSP pkt: [chars]Explanation Invalid PTSP packet has been received.
Recommended Action Check the sender of the packet for a possible problem.
Error Message %PNNI-4-INTERNAL_ERROR: Can't find node included in ACK header: [chars] , pnni_nodeid_string(node_id)Explanation Cannot locate node in an ACK packet.
Recommended Action If this message recurs, contact your technical support representative for assistance.
Error Message %PNNI-4-INTERNAL_ERROR: Hello state machine error in state [chars] , error_msgExplanation An internal software error has occurred.
Recommended Action If this message recurs, contact your technical support representative for assistance.
Error Message %PNNI-4-CONFIG_ERROR: Configuration Error: Neighbor in different PeerGroupExplanation Neighbor indicates that it is a different peergroup. This software version does not support multiple peer groups.
Recommended Action Correct switch address to be part of the same peer group.
Error Message %PNNI-4-INTERNAL_ERROR: Cannot add NNI interface, uninitialized pointersExplanation Neighbor indicates that it is a different peergroup. This software version does not support multiple peer groups.
Recommended Action Correct switch address to be part of the same peer group.
Error Message %PNNI-4-INTERNAL_ERROR: Getting Node Id For An Invalid Node [hex], nodeExplanation Neighbor indicates that it is a different peergroup. This software version does not support multiple peer groups.
Recommended Action Correct switch address to be part of the same peer group.
Error Message %PNNI-4-INTERNAL_ERROR: Null element to deq_ptseExplanation Neighbor indicates that it is a different peergroup. This software version does not support multiple peer groups.
Recommended Action Correct switch address to be part of the same peer group.
Error Message %PNNI-4-INTERNAL_ERROR: Null element to deq_ptseExplanation Neighbor indicates that it is a different peergroup. This software version does not support multiple peer groups.
Recommended Action Correct switch address to be part of the same peer group.
Error Message %PNNI-4-INTERNAL_ERROR: Can't find our own node in PTSE databaseExplanation Neighbor indicates that it is a different peergroup. This software version does not support multiple peer groups.
Recommended Action Correct switch address to be part of the same peer group.
Error Message %PNNI-2-SPF_ERROR: Tent List Overflow in min_aw_route_od()Explanation Number of nodes in the network exceeds the node limit of the internal SPF data structure.
Recommended Action If this message recurs, contact your technical support representative for assistance.
Error Message %PNNI-2-SPF_ERROR: Tent List Overflow in min_cdv_route_od()Explanation Number of nodes in the network exceeds the node limit of the internal SPF data structure.
Recommended Action If this message recurs, contact your technical support representative for assistance.
Error Message %PNNI-2-SPF_ERROR: Tent List Overflow in min_ctd_route_od()Explanation Number of nodes in the network exceeds the node limit of the internal SPF data structure.
Recommended Action If this message recurs, contact your technical support representative for assistance.
Error Message %PNNI-2-SPF_ERROR: Tent List Overflow in min_aw_dijkstra_bg()Explanation Number of nodes in the network exceeds the node limit of the internal SPF data structure.
Recommended Action If this message recurs, contact your technical support representative for assistance.
Error Message %PNNI-2-SPF_ERROR: Tent List Overflow in min_cdv_dijkstra_bg()Explanation Number of nodes in the network exceeds the node limit of the internal SPF data structure.
Recommended Action If this message recurs, contact your technical support representative for assistance.
Error Message %PNNI-2-SPF_ERROR: Tent List Overflow in min_ctd_dijkstra_bg()Explanation Number of nodes in the network exceeds the node limit of the internal SPF data structure.
Recommended Action If this message recurs, contact your technical support representative for assistance.
Error Message %PNNI-2-SPF_ERROR: Tent List Overflow in min_hop_route_all()Explanation Number of nodes in the network exceeds the node limit of the internal SPF data structure.
Recommended Action If this message recurs, contact your technical support representative for assistance.
Error Message %PNNI-4-INTERNAL_ERROR: PDB is NULL on a Route Request!!! [hex], msg->op_codeExplanation Bad request from signaling process error.
Recommended Action If this message recurs, contact your technical support representative for assistance.
Error Message %PNNI-4-INTERNAL_ERROR: Unknown timer type [hex]Explanation Bad request from signaling process error.
Recommended Action If this message recurs, contact your technical support representative for assistance.
Error Message %PNNI-4-INTERNAL_ERROR: IF table full, cannot add new interface [hex]Explanation No more entries in the interface table are allowed. The maximum number of entries is 256.
Recommended Action Do not add anymore entries in the interface table.
Explanation The unit described has a memory error for the IDB structure.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %SONICT-1-INITFAIL: Unit [dec], initialization timeout failure, csr [dec]=0x%04xExplanation The unit described has an initialization timeout failure, cell missequenced ratio.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %SONICT-3-SPURIDON: Unit [dec], spurious IDON interrupt, csr [dec]=0x%04xExplanation The unit described has a spurious IDON interrupt, cell missequenced ratio.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %SONICT-3-OWNERR: Unit [dec], buffer ownership error, pak = 0x [hex]Explanation The unit described has a buffer ownership error.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %SONICT-3-INTERNAL_ERROR: sonic_send: semaphore lockedExplanation SONIC send error. Semaphore locked.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %SONICT-3-INTERNAL_ERROR: sonic_send: no free tbufsExplanation SONIC send error. No free transmit buffers.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %SONICT-3-INTERNAL_ERROR: sonic_send: tp not freeExplanation SONIC send error. tp not free.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %SONICT-3-INTERNAL_ERROR: sonic_send: PANIC: sonicT is still using this tdaExplanation SONIC send error. SONICT is still using this tda.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %SONICT-3-INTERNAL_ERROR: sonic_send: TXP did not clearExplanation SONIC send error. TXP did not clear.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %SONICT-3-XMIT_ERR: TX Error [hex]Explanation Transmit error.
Recommended Action If this message occurs, contact your technical support representative for assistance.
Error Message %SONICT-3-INTERNAL_ERROR: sonic ISR: BAD NEWS, got RBE intExplanation SONIC ISR error. Got RBE interface.
Recommended Action If this message occurs, contact your technical support representative for assistance.
|
|