|
|
This chapter provides a quick command reference for the Catalyst 5000 series ATM module CLI.
Table 9-1 identifies each command in the ATM module command set, gives the command syntax, provides a short description, and specifies the command type and mode.
| Command | Syntax | Description | Type1 | Mode2 |
|---|---|---|---|---|
| atm bind pvc vlan | atm bind pvc vlan vcd vlan_num | Binds a PVC to a specified VLAN. | ATM | IC |
| atm ilmi-keepalive | [no] atm ilmi-keepalive seconds | Enables ILMI keepalives. | ATM | IC |
| atm preferred phy | atm preferred phy {A | B} | Changes the preferred PHY. | LANE | EXEC |
| atm pvc | [no] atm pvc vcd vpi vci [aal5snap | ilmi | qsaal]
[no] atm pvc vcd vpi vci [aal5snap | ilmi | qsaal] [peak_rate average_rate [burst_size]] [oam seconds]3 | Creates a PVC on the ATM interface. | ATM | IC |
| atm traffic-shape rate | [no] atm traffic-shape rate 1-155 | Configures output throttling on the ATM module. | ATM | IC |
| atm uni-version | atm uni-version version_number no atm uni-version | Specifies the UNI version to be used. | ATM | IC |
| atm vc-per-vp | atm vc-per-vp number no atm vc-per-vp | Sets the maximum number of VCIs to support per VCI. | ATM | IC |
| atmsig close | atmsig close atm0 vcd | Disconnects an SVC. | ATM | EXEC |
| client-atm-address name | client-atm-address atm-address-template name elan-name no client-atm-address atm-address-template | Adds a LANE address entry to the configuration server's database. | LANE | Dbase |
| default-name | default-name elan-name no default name | Provides a default ELAN name in the configuration server's database. | ATM | Dbase |
| disable | disable [level] | Exits privileged EXEC mode and returns to user EXEC mode. | ATM | EXEC |
| editing | [no] editing | Enables enhanced editing mode. | ATM | Line |
| enable | enable | Enters privileged EXEC mode. | ATM | EXEC |
| end | end | Exits configuration mode. | ATM | GC |
| exit | exit | Exits any command mode or closes an active terminal session and terminates the EXEC. | ATM | ATM |
| help | help | Displays the help commands. | ATM | ATM |
| history | [no] history [size number-of-lines] | Enables the command history function. | ATM | Line |
| lane auto-config-atm-address | [no] lane auto-config-atm-address | Specifies that the configuration server ATM address be computed automatically. | ATM | IC |
| lane client | lane client ethernet vlan# [elan-name] no lane client [ethernet vlan# [elan-name]] | Activates a LANE client. | LANE | IC |
| lane client-atm-address | lane client-atm-address atm-address-template no client-atm-address [atm-address-template] | Specifies an ATM address for the LANE client (overriding automatic assignment). | LANE | IC |
| lane config-atm-address | lane config-atm-address atm-address-template no lane config-atm-address [atm-address-template] | Specifies the ATM address of a given configuration server. | LANE | IC |
| lane config database | lane config database database-name no lane config database | Associates a named configuration database with the configuration server on the selected ATM interface. | LANE | GC |
| lane database | [no] lane database database-name | Creates a named configuration database that can be associated with a configuration server. | LANE | GC |
| lane le-arp | [no] lane le-arp mac-addr atm-addr | Adds a static entry to the LE ARP table. | LANE | IC |
| lane register | lane register vcd mac-addr atm-addr no lane register vcd [mac-addr atm-addr] | Registers a LANE client. | LANE | IC |
| lane server-bus | [no] lane server-bus ethernet elan_name | Configures the LES and BUS for the specified ELAN on the subinterface. | LANE | IC |
| name server-atm-address | [no] name elan_name server-atm-address atm-addr | Assigns a unique ELAN name to a LES. | LANE | Dbase |
| reload | reload | Reloads the operating system. | Config | EXEC |
| show atm interface atm | show atm interface atm0 | Displays information about the ATM interface. | ATM | EXEC |
| show atm traffic | show atm traffic | Displays global ATM traffic information. | ATM | EXEC |
| show atm vc | show atm vc [vcd] | Displays the active ATM virtual circuits. | ATM | EXEC |
| show atm vlan | show atm vlan [vlan_num] | Displays the active VLAN-to-PVC bindings. | ATM | IC |
| show history | show history | Lists the command history for the current EXEC session. | ATM | EXEC |
| show lane | show lane [interface atm0[.subinterface] | name elan-name] [brief] | Displays global and per-VCC LANE information. | LANE | EXEC |
| show lane bus | show lane bus [interface atm0[.subinterface] | name elan-name] [brief] | Displays LANE information for the configured BUS. | LANE | EXEC |
| show lane client | show lane client [interface atm0[.subinterface] | name elan-name] [brief] | Displays global and per-VCC LANE information. | LANE | EXEC |
| show lane config | show lane config [interface atm0] [brief] | Displays LANE information for the LECS. | LANE | EXEC |
| show lane default-atm-addresses | show lane default-atm-addresses | Displays default ATM addresses for dual PHYs. | LANE | EXEC |
| show lane le-arp | show lane le-arp [interface atm0[.subinterface] | name elan-name] | Displays the LE ARP table. | LANE | EXEC |
| show lane server | show lane server [interface atm0[.subinterface] | name elan-name] [brief] | Displays LANE information about the configured LES. | LANE | EXEC |
| show sscop | show sscop | Displays SSCOP details for all ATM interfaces. | ATM | EXEC |
| show version | show version | Displays version information for the ATM module. | Config | EXEC |
| sscop cc-timer | sscop cc-timer seconds no sscop cc-timer | Changes the SSCOP connection control timer period. | ATM | IC |
| sscop keepalive-timer | [no] sscop keepalive-timer seconds | Changes the SSCOP keepalive timer period. | ATM | IC |
| sscop max-cc | sscop max-cc retries no sscop max-cc | Changes the SSCOP connection control retry count. | ATM | IC |
| sscop poll-timer | sscop poll-timer seconds no sscop poll-timer | Changes the SSCOP poll timer period. | ATM | IC |
| sscop rcv-window | sscop rcv-window packets no sscop rcv-window | Changes the size of the SSCOP receiver window. | ATM | IC |
| sscop send-window | sscop send-window packets no sscop send-window | Changes the size of the SSCOP transmitter window. | ATM | IC |
| terminal | terminal length [screen-length] terminal no length | Sets the number of lines displayed on the terminal. | ATM | EXEC |
| write erase | write erase | Erases the configuration information in NVRAM. | Config | EXEC |
| write memory | write memory | Copies the configuration information in running memory to NVRAM. | Config | EXEC |
| write terminal | write terminal | Displays the configuration information currently in running memory. | Config | EXEC |
|
|