|
|
| Event Description | Trap Number | Trap Summary | Node Severity |
|---|---|---|---|
| 00_00: A Restart occured after a system crash; a Clear is sent; the info indicates CPU status. | 90000 | System Restart after crash (from <Node X.25 Address>, info=<Info>) | major |
| 00_01: Correct reset of FastPADmpr has occurred; info indicates: Module number, backup type. | 90001 | FastPADmpr reset (from <Node X.25 Address>, info=<Info>) | normal |
| 00_02: A failure occurred on FastPADmpr Module 0; info indicates: Module number, backup type. | 90002 | FastPADmpr Module 0 failure (from <Node X.25 Address>, info=<Info>) | minor |
| 00_03: A failure occurred on FastPADmpr Module 1. info indicates: Module number, backup type. | 90003 | FastPADmpr Module 1 failure (from <Node X.25 Address>, info=<Info>) | minor |
| 00_04: A failure occurred on FastPADmpr Module 2. info indicates: Module number, backup type. | 90004 | FastPADmpr Module 2 failure (from <Node X.25 Address>, info=<Info>) | minor |
| 00_05: A correct reset of FastPADmp has occurred. | 90005 | FastPADmp reset (from <Node X.25 Address>) | normal |
| 00_06: FastPADmpr Module 0 is in standby mode, backed up, awaiting unit reset. info indicates: Module number, backup type. | 90006 | FastPADmpr Module 0 standby (from <Node X.25 Address>, info=<Info>) | normal |
| 00_07: FastPADmpr Module 1 is in standby mode, backed up, awaiting unit reset. info indicates: Module number, backup type. | 90007 | FastPADmpr Module 1 standby (from <Node X.25 Address>, info=<Info>) | normal |
| 00_08: FastPADmpr Module 2 is in standby mode, backed up, awaiting unit reset. info indicates: Module number, backup type. | 90008 | FastPADmpr Module 2 standby (from <Node X.25 Address>, info=<Info>) | normal |
| 00_09: Initiation of the module auto-loading operation has occurred; info indicates: loading module, loaded module, cause: 01 = configurations are different, 02 = different software versions, 03 = module running BOOT program. | 90009 | Start of auto-loading (from <Node X.25 Address>, info=<Info>) | normal |
| 00_0A: Completion of the module auto-loading operation has occurred; info indicates: status after loading: 80 = OK, 82 = write or sequence error, 83 = time-out. | 90010 | End of auto-loading (from <Node X.25 Address>, info=<Info>) | normal |
| 00_0B: A Startcard problem was detected and successfully corrected. | 90011 | Startcard problem (from <Node X.25 Address>) | warning |
| 00_0C: The system is restarted due to operator initiated action. | 90012 | Operator initiated system startup (from <Node X.25 Address>) | normal |
| 00_0D: The system is restarted due to a hardware reset or initial startup. | 90013 | Hardware reset system startup (from <Node X.25 Address>) | normal |
| 00_0E: FastPADmpr Module 0 has gone offline; info indicates: module number, event generator, backup type. | 90014 | FastPADmpr Module 0 offline (from <Node X.25 Address>, info=<Info>) | warning |
| 00_0F: FastPADmpr Module 0 has come online; info indicates: module number, event generator, backup type. | 90015 | FastPADmpr Module 0 online (from <Node X.25 Address>, info=<Info>) | normal |
| 00_10: FastPADmpr Module 1 has gone offline; info indicates: module number, event generator, backup type. | 90016 | FastPADmpr Module 1 offline (from <Node X.25 Address>, info=<Info>) | warning |
| 00_11: FastPADmpr Module 1 has come online; info indicates: module number, event generator, backup type. | 90017 | FastPADmpr Module 1 online (from <Node X.25 Address>, info=<Info>) | normal |
| 00_12: FastPADmpr Module 2 has gone offline; info indicates: module number, event generator, backup type. | 90018 | FastPADmpr Module 2 offline (from <Node X.25 Address>, info=<Info>) | warning |
| 00_13: FastPADmpr Module 2 has come online; info indicates: module number, event generator, backup type. | 90019 | FastPADmpr Module 2 online (from <Node X.25 Address>, info=<Info>) | normal |
| 01_13: An erroneous command was received; the circuit is Cleared. | 90275 | Erroneous command received (from <Node X.25 Address>) | warning |
| 01_14: A data packet was received before an expected command acknowledgement was received; the circuit is Cleared. | 90276 | Data received before command ACK (from <Node X.25 Address>) | warning |
| 01_16: The billing ticket threshold has been exceeded; the circuit is Cleared. | 90278 | Billing ticket threshold exceeded (from <Node X.25 Address>) | warning |
| 01_17: The oldest detailed billing ticket has been lost; the circuit is Cleared; info indicates: module that lost ticket, number of tickets lost. | 90279 | Oldest detailed billing ticket lost (from <Node X.25 Address>, info=<Info>) | warning |
| 01_20: The node has accepted the download operation. | 90288 | Download operation accepted (from <Node X.25 Address>) | normal |
| 01_21: The node has refused the download operation due to no RAM storage being available. | 90289 | Download refused: no RAM (from <Node X.25 Address>) | minor |
| 01_22: The node has refused the download operation due to no Flash PROM storage being available. | 90290 | Download refused: no Flash PROM (from <Node X.25 Address>) | minor |
| 01_23: The node has completed the download operation with no errors. | 90291 | Download complete: no error (from <Node X.25 Address>) | normal |
| 01_24: The node has completed the download operation with a result of checksum error. | 90292 | Download failed: checksum error (from <Node X.25 Address>) | minor |
| 01_25: The node has completed the download operation with a result of incomplete load. | 90293 | Download failed: incomplete load (from <Node X.25 Address>) | minor |
| 01_26: The node has completed the downloading operation with a result of bad version. | 90294 | Download failed: bad version (from <Node X.25 Address>) | minor |
| 01_27: The node has accepted the uploading operation. | 90295 | Upload operation accepted (from <Node X.25 Address>) | normal |
| 01_28: The node has refused the upload operation due to no RAM storage being available. | 90296 | Upload refused: no RAM (from <Node X.25 Address>) | minor |
| 01_29: The node has refused the upload operation due to no Flash PROM storage being available. | 90297 | Upload refused: no Flash PROM (from <Node X.25 Address>) | minor |
| 01_2A: The node has completed the upload operation with no errors. | 90298 | Upload complete: no error (from <Node X.25 Address>) | normal |
| 01_2B: The node has completed the upload operation with a result of checksum error. | 90299 | Upload failed: checksum error (from <Node X.25 Address>) | minor |
| 01_2C: The node has completed the upload operation with a result of incomplete load. | 90300 | Upload failed: incomplete load (from <Node X.25 Address>) | minor |
| 01_2D: The node has completed the upload operation with a result of bad version. | 90301 | Upload failed: bad version (from <Node X.25 Address>) | minor |
| 01_2E: The node has completed the uploading operation and copied RAM to FPROM. | 90302 | Upload complete: copied RAM to FPROM (from <Node X.25 Address>) | normal |
| 01_30: A Call has been setup to a Management Access Point; info indicates: maximum MAPs, MAPs open. | 90304 | Call setup with MAP (from <Node X.25 Address>, info=<Info>) | normal |
| 01_31: No Logical Channel is available for completing setup of a Management Access Point session. | 90305 | LC unavailable for MAP session (from <Node X.25 Address>) | warning |
| 01_32: The maximum number of concurrent Management Access Point sessions has been reached; the MAP Call is Cleared; info indicates: maximum MAPs. | 90306 | Maximum MAP sessions (from <Node X.25 Address>, info=<Info>) | warning |
| 01_33: A Management Access Point session has been opened. | 90307 | MAP session opened (from <Node X.25 Address>) | normal |
| 01_34: A Management Access Point session open attempt failed; the MAP menu is displayed. | 90308 | MAP session open failed (from <Node X.25 Address>) | warning |
| 01_35: A Management Access Point session was Cleared from a remote node; the MAP menu is displayed. | 90309 | MAP session Cleared by remote (from <Node X.25 Address>) | normal |
| 01_36: A Management Access Point session is closed; the MAP menu is displayed. | 90310 | MAP session closed (from <Node X.25 Address>) | normal |
| 01_37: A Management Access Point Call was Cleared. | 90311 | MAP Call Cleared (from <Node X.25 Address>) | normal |
| 01_C0: The Sample number in Extended Statistics is exceeded. | 90448 | Sample number exceeded (from <Node X.25 Address>) | warning |
| 01_C1: The Sampling counter in Extended Statistics is full. | 90449 | Sampling counter full (from <Node X.25 Address>) | warning |
| 01_C2: The Hour counter in Extended Statistics is full. | 90450 | Hour counter full (from <Node X.25 Address>) | warning |
| 01_C3: The Threshold-Exceeded counter in Extended Statistics is full. | 90451 | Threshold-Exceeded counter full (from <Node X.25 Address>) | warning |
| 01_C4: The Day counter in Extended Statistics is full. | 90452 | Day counter full (from <Node X.25 Address>) | warning |
| 01_C5: A Configuration error in Extended Statistics has occurred. | 90453 | Configuration error (from <Node X.25 Address>) | warning |
| 01_D0: An invalid value was detected on a configuration parameter for DLM; the Management Access Point is Cleared. | 90464 | Configuration parameter invalid on DLM (from <Node X.25 Address>, line <Port Number>) | warning |
| 01_D1: The minimum threshold was not exceeded on DLM; the throughput is lower than the maximum threshold; info indicates: rate of last period (4 bytes), secondary line number, line status, maximum data rate (4 bytes), line cost. | 90465 | Minimum threshold not exceeded on DLM (from <Node X.25 Address>, line <Port Number>, info=<Info>) | normal |
| 01_D2: The maximum threshold has been exceeded on DLM; info indicates: rate of last period (4 bytes), secondary line number, line status, maximum data rate (4 bytes), line cost. | 90466 | Maximum threshold exceeded on DLM (from <Node X.25 Address>, line <Port Number>, info=<Info>) | normal |
| 01_E3: A Call was received with an incorrect password; the Call is Cleared. | 90483 | Call received with incorrect password (from <Node X.25 Address>) | warning |
| 01_E5: A Call was received with an incorrect parameter; the Call is Cleared. | 90485 | Call received with incorrect parameter (from <Node X.25 Address>) | warning |
| 01_E9: An incorrect Statistics function command was entered; the circuit is Reset. | 90489 | Incorrect Statistics function command (from <Node X.25 Address>) | warning |
| 02_00: A Call was rejected due to the maximum number of concurrent SVCs being reached. | 90512 | Maximum VCs reached (from <Node X.25 Address>, line <Port Number>) | minor |
| 02_02: A Call was rejected due to a Call Request packet being too long. | 90514 | Call Request too long (from <Node X.25 Address>, line <Port Number>) | warning |
| 02_03: A Call was rejected due to a Call Request packet being too short. | 90515 | Call Request too short (from <Node X.25 Address>, line <Port Number>) | warning |
| 02_05: A Call was rejected due to the calling address in a received Call Request being too short. | 90517 | Calling address too short (from <Node X.25 Address>, line <Port Number>) | warning |
| 02_08: A Call was rejected due to an incorrect facility or utility field in a received Call Request. | 90520 | Incorrect facility in Call (from <Node X.25 Address>, line <Port Number>) | warning |
| 02_09: A Call was rejected due to a duplicate facility or utility field in a received Call Request. | 90521 | Duplicate facility in Call (from <Node X.25 Address>, line <Port Number>) | warning |
| 02_0B: A Call was rejected due to an unauthorized facility or utility field in a received Call Request. | 90523 | Unauthorized facility in Call (from <Node X.25 Address>, line <Port Number>) | warning |
| 02_0C: A Call was rejected due to a routing being impossible in a received Call Request; the called DNIC is unknown or the associated routing has not been configured; info indicates: Called DNIC. | 90524 | Routing impossible in Call (from <Node X.25 Address>, line <Port Number>, info=<Info>) | warning |
| 02_0F: A Call was cleared due to receipt of a Call Confirmation that is too long. | 90527 | Call Confirmation too long (from <Node X.25 Address>, line <Port Number>) | warning |
| 02_10: A Call was cleared due to receipt of a Call Confirmation that is too short. | 90528 | Call Confirmation too short (from <Node X.25 Address>, line <Port Number>) | warning |
| 02_12: A Call was cleared due to receipt of a Call Confirmation with an error in a facility or utility field. | 90530 | Call Confirmation error (from <Node X.25 Address>, line <Port Number>) | warning |
| 02_14: A Call was cleared due to receipt of a Call Confirmation with a duplicate facility or utility field. | 90532 | Duplicate facility in Call Confirmation (from <Node X.25 Address>, line <Port Number>) | warning |
| 02_15: A Call was cleared due to receipt of a Call Confirmation with an unauthorized facility or utility field. | 90533 | Unauthorized facility in Call Confirmation (from <Node X.25 Address>, line <Port Number>) | warning |
| 02_17: A Call was cleared due to receipt of a Call Confirmation with an invalid throughput class value. | 90535 | Invalid throughput class in Call Confirmation (from <Node X.25 Address>, line <Port Number>) | warning |
| 02_18: A Call was cleared due to receipt of a Call Confirmation with an invalid window size value. | 90536 | Invalid window size in Call Confirmation (from <Node X.25 Address>, line <Port Number>) | warning |
| 02_20: A Call was cleared due to receipt of a Call Request with a non-numeric address. | 90544 | Non-numeric address in Call Request (from <Node X.25 Address>, line <Port Number>) | warning |
| 02_22: A Call was cleared due to receipt of a Call Request with too many ZO's. | 90546 | Too many ZO's in Call Request (from <Node X.25 Address>, line <Port Number>) | warning |
| 02_23: A Call was cleared due to receipt of a Call Confirmation with a non-numeric address. | 90547 | Non-numeric address in Call Confirmation (from <Node X.25 Address>, line <Port Number>) | warning |
| 02_26: A Call was cleared due to receipt of a Call Confirmation with an invalid packet size. | 90550 | Invalid packet size in Call Confirmation (from <Node X.25 Address>, line <Port Number>) | warning |
| 02_27: A Call was cleared due to receipt of a Call Confirmation with an incomplete called address. | 90551 | Incomplete called address in Call Confirmation (from <Node X.25 Address>, line <Port Number>) | warning |
| 02_28: A Call was cleared due to an incorrect PDN line table entry. | 90552 | Incorrect PDN line table (from <Node X.25 Address>, line <Port Number>) | warning |
| 02_29: A Call was cleared due to a decompacted address not being found in tables. | 90553 | Decompacted address not found (from <Node X.25 Address>, line <Port Number>) | warning |
| 02_2A: A Call was cleared due to a compacted address not being found in tables. | 90554 | Compacted address not found (from <Node X.25 Address>, line <Port Number>) | warning |
| 02_2B: A Call was cleared due to decompacting not being possible. | 90555 | Decompacting not possible (from <Node X.25 Address>, line <Port Number>) | warning |
| 02_2C: A Call was cleared due to compacting not being possible. | 90556 | Compacting not possible (from <Node X.25 Address>, line <Port Number>) | warning |
| 02_2E: A Call was cleared due to a requested internal subscriber being offline; info indicates: Called DNIC. | 90558 | Internal subscriber offline (from <Node X.25 Address>, line <Port Number>, info=<Info>) | warning |
| 02_30: A Call was cleared due to a requested output line being down; info indicates: Called DNIC. | 90560 | Output line is down (from <Node X.25 Address>, line <Port Number>, info=<Info>) | normal |
| 02_31: A Call was cleared due to receipt of a Clear with a non-numeric address. | 90561 | Non-numeric address in Clear (from <Node X.25 Address>, line <Port Number>) | warning |
| 02_32: A Call was cleared due to an error in received Clear address, facility or utility lengths. | 90562 | Inconsistent lengths in Clear (from <Node X.25 Address>, line <Port Number>) | warning |
| 02_33: A Call was cleared due to receipt of a Clear with length values that do not conform to the X.25 standards. | 90563 | Non-standard length in Clear (from <Node X.25 Address>, line <Port Number>) | warning |
| 02_34: A Call was cleared due to receipt of a Clear with an incorrect facility or utility field. | 90564 | Incorrect facility in Clear (from <Node X.25 Address>, line <Port Number>) | warning |
| 02_35: A Call was cleared due to receipt of a Clear with a duplicate facility or utility field. | 90565 | Duplicate facility in Clear (from <Node X.25 Address>, line <Port Number>) | warning |
| 02_36: A Call was cleared due to receipt of a Call Return that is not authorized. | 90566 | Unuathorized Call Return (from <Node X.25 Address>, line <Port Number>) | warning |
| 02_3C: A Call Return was received with inconsistencies in type between the incoming and outgoing lines; the Call is Cleared. | 90572 | Inconsistent Call Return type (from <Node X.25 Address>, line <Port Number>) | warning |
| 02_3D: A Call Request was received with an unmanaged utility on an X.75 line; the Call is Cleared; info indicates: utility code received. | 90573 | Unmanaged utility in Call Request on X.75 (from <Node X.25 Address>, line <Port Number>, info=<Info>) | warning |
| 02_3E: A Call Confirmation was received with an unmanaged utility on an X.75 line; the Call is Cleared; info indicates: utility code received. | 90574 | Unmanaged utility in Call Confirmation on X.75 (from <Node X.25 Address>, line <Port Number>, info=<Info>) | warning |
| 02_3F: A Clear was received with an unmanaged utility on an X.75 line; the Call is Cleared; info indicates: utility code received. | 90575 | Unmanaged utility in Clear on X.75 (from <Node X.25 Address>, line <Port Number>, info=<Info>) | warning |
| 02_40: A Call Request was received on an X.75 line without a required "Identification of Call" utility; the Call is Cleared. | 90576 | Missing "Call-ID" utility in Call Request on X.75 (from <Node X.25 Address>, line <Port Number>) | warning |
| 02_41: A Closed User Group facility was present in a Call Request to be sent on an X.75 line; the Call is Cleared; info indicates: CUG number. | 90577 | CUG present in Call Request on X.75 (from <Node X.25 Address>, line <Port Number>, info=<Info>) | warning |
| 02_50: A routable line came online; the line is placed in service. | 90592 | Routable line online (from <Node X.25 Address>, line <Port Number>) | normal |
| 02_51: A routable line went offline; the line is taken out of service. | 90593 | Routable line offline (from <Node X.25 Address>, line <Port Number>) | minor |
| 03_00: An unknown address was received in an X.25 frame; the frame is ignored; info indicates: byte1 of frame. | 90768 | Unknown address in X.25 frame (from <Node X.25 Address>, line <Port Number>, info=<Info>) | warning |
| 03_01: An X.25 Frame of incorrect length was received; the frame was ignored if it was an I-frame or an FRMR was sent if it was a U or S-frame; info indicates: length of frame, byte1 of frame, byte2 of frame. | 90769 | Incorrect length in X.25 frame (from <Node X.25 Address>, line <Port Number>, info=<Info>) | warning |
| 03_02: An X.25 Frame with inverted address was received. | 90770 | Inverted address in X.25 frame (from <Node X.25 Address>, line <Port Number>) | warning |
| 03_03: An X.25 frame with an unknown command was received; an FRMR was sent with W=1; info indicates: byte2 of frame. | 90771 | Unknown command in X.25 frame (from <Node X.25 Address>, line <Port Number>, info=<Info>) | warning |
| 03_04: An X.25 frame with an unknown response was received; an FRMR was sent with W=1; info indicates: byte2 of frame. | 90772 | Unknown response in X.25 frame (from <Node X.25 Address>, line <Port Number>, info=<Info>) | warning |
| 03_05: An X.25 frame was received without the F-bit set after sending a frame with the P-bit set; the frame is ignored. | 90773 | X.25 frame without F-bit after P-bit (from <Node X.25 Address>, line <Port Number>) | warning |
| 03_06: An X.25 frame was received with the F-bit set after sending a frame without the P-bit set; the frame is ignored. | 90774 | X.25 frame with F-bit after no P-bit (from <Node X.25 Address>, line <Port Number>) | warning |
| 03_07: An unexpected X.25 frame was received while in DISCONNECTED mode; info indicates: byte1 of frame, byte2 of frame. | 90775 | Unexpected X.25 frame in DISCONNECTED mode (from <Node X.25 Address>, line <Port Number>, info=<Info>) | warning |
| 03_08: X.25 Level 1 (physical) link is down and Level 2 retries are being attempted; line = 0-35 for physical link, line = 36-41 for inter-unit link, line = 50-55 for inter-module link. | 90776 | X.25 Link down (from <Node X.25 Address>, line <Port Number>) | major |
| 03_09: X.25 Level 1 (physical) link is up and Level 2 retries are being attempted; line = 0-35 for physical link, line = 36-41 for inter-unit link, line = 50-55 for inter-module link. | 90777 | X.25 Link up (from <Node X.25 Address>, line <Port Number>) | normal |
| 03_0A: An unexpected X.25 frame was received while in CONNECTED mode; the frame is ignored; info indicates: byte1 of frame, byte2 of frame. | 90778 | Unexpected X.25 frame in CONNECTED mode (from <Node X.25 Address>, line <Port Number>, info=<Info>) | warning |
| 03_0B: An invalid X.25 frame was received while in the FRMR state; an FRMR was sent; info indicates: byte2 of frame. | 90779 | Invalid X.25 frame in FRMR state (from <Node X.25 Address>, line <Port Number>, info=<Info>) | warning |
| 03_0C: An X.25 frame with an incorrect N(R) was received; an FRMR was sent with Z=1; info indicates: byte2 of frame. | 90780 | X.25 frame with incorrect N(R) received (from <Node X.25 Address>, line <Port Number>, info=<Info>) | warning |
| 03_0E: An X.25 frame was received out of sequence or with a duplicate N(R); an FRMR was sent; info indicates: byte2 of frame. | 90782 | X.25 frame out of sequence or duplicate N(R) (from <Node X.25 Address>, line <Port Number>, info=<Info>) | warning |
| 03_0F: An X.25 frame was received outside the sequence window; an FRMR was sent; info indicates: byte2 of frame. | 90783 | X.25 frame received outside sequence window (from <Node X.25 Address>, line <Port Number>, info=<Info>) | warning |
| 03_10: An X.25 FRMR frame was received; a SABM was sent. | 90784 | X.25 FRMR received (from <Node X.25 Address>, line <Port Number>) | normal |
| 03_12: An invalid expiration of timeout T1 occurred. | 90786 | Invalid expiration of T1 timeout on X.25 (from <Node X.25 Address>, line <Port Number>) | warning |
| 03_13: An X.25 packet was received with an invalid GFI; a Clear, Restart or Reset was sent, depending on the state of the Packet Level; info indicates: byte3 of frame. byte5 of frame. | 90787 | X.25 packet with invalid GFI (from <Node X.25 Address>, line <Port Number>, info=<Info>) | warning |
| 03_14: An X.25 Restart or Restart Confirmation was received on a channel other than Logical Channel #0; info indicates: byte3 of frame. byte4 of frame. | 90788 | X.25 Restart or Restart Confirmation not on LC#0 (from <Node X.25 Address>, line <Port Number>, info=<Info>) | warning |
| 03_15: An X.25 Restart Confirmation was received without a Restart having been sent; Restart is sent; info indicates: packet level state: 1 = packet level inactive due to frame level down, 2 = packet level in service, 3 = reply confirmation to be sent, 4 = awaiting restart confirmation, 5 = restart to be sent. | 90789 | X.25 Restart Confirmation without Restart sent (from <Node X.25 Address>, line <Port Number>, info=<Info>) | warning |
| 03_16: An unexpected X.25 packet was received during Restart; info indicates: byte5 of frame. | 90790 | Unexpected packet during X.25 Restart (from <Node X.25 Address>, line <Port Number>, info=<Info>) | warning |
| 03_17: An X.25 Restart was re-sent after a timeout; now waiting a Confirmation. | 90791 | Re-sending X.25 Restart on timeout (from <Node X.25 Address>, line <Port Number>) | warning |
| 03_18: An X.25 packet was received on an un-configured Logical Channel; a Clear is sent; info indicates: byte3 of frame, byte4 of frame, byte5 of frame. | 90792 | X.25 packet on un-configured LC (from <Node X.25 Address>, line <Port Number>, info=<Info>) | warning |
| 03_19: An unexpected X.25 packet was received on a free Logical Channel; info indicates: byte5 of frame. | 90793 | Unexpected X.25 packet on free LC (from <Node X.25 Address>, line <Port Number>, info=<Info>) | warning |
| 03_1A: An X.25 Clear Confirmation was received on a free Logical Channel. | 90794 | X.25 Clear Confirmation received on free LC (from <Node X.25 Address>, line <Port Number>) | warning |
| 03_1B: An X.25 Clear was received on a free Logical Channel. | 90795 | X.25 Clear received on free LC (from <Node X.25 Address>, line <Port Number>) | warning |
| 03_1C: An X.25 Clear Confirmation was received without having sent a Clear; info indicates: Logical Channel state: 1 = LC allocated due to receipt of this Clear Confirmation, 2 = LC ready (in data transfer mode). | 90796 | X.25 Clear Confirmation received without Clear sent (from <Node X.25 Address>, line <Port Number>, info=<Info>) | warning |
| 03_1D: An unexpected X.25 packet was received after a Clear was received; info indicates: byte5 of frame. | 90797 | Unexpected X.25 packet received after Clear (from <Node X.25 Address>, line <Port Number>, info=<Info>) | warning |
| 03_1E: An unexpected X.25 packet was received on an established SVC; a Clear was sent; info indicates: byte5 of frame. | 90798 | Unexpected X.25 packet on established SVC (from <Node X.25 Address>, line <Port Number>, info=<Info>) | warning |
| 03_1F: An unexpected X.25 Call was received after a Call Request had been sent; a Clear was sent; info indicates: byte5 of frame. | 90799 | Unexpected X.25 Call received after Call sent (from <Node X.25 Address>, line <Port Number>, info=<Info>) | warning |
| 03_20: An X.25 Call collision occurred; a Clear was sent. | 90800 | X.25 Call collision (from <Node X.25 Address>, line <Port Number>) | warning |
| 03_21: An unexpected X.25 packet was received after a Call was received; a Clear was sent; info indicates: byte5 of frame. | 90801 | Unexpected X.25 packet received after Call (from <Node X.25 Address>, line <Port Number>, info=<Info>) | warning |
| 03_22: A packet was received of an unknown type on an X.25 line; info indicates: byte5 of frame. | 90802 | Unknown packet type received on X.25 (from <Node X.25 Address>, line <Port Number>, info=<Info>) | warning |
| 03_23: An X.25 Clear was sent after a time-out; now waiting for a Clear Confirmation. | 90803 | Awaiting Clear Confirmation after timeout on X.25 (from <Node X.25 Address>, line <Port Number>) | warning |
| 03_24: An X.25 Call Request was sent after a time-out; now waiting for a Call Confirmation. | 90804 | Awaiting Call Confirmation after timeout on X.25 (from <Node X.25 Address>, line <Port Number>) | warning |
| 03_25: An X.25 Reset Confirmation was received without having sent a Reset; info indicates: Logical Channel state: 1 = LC allocated due to receipt of this Clear Confirmation, 2 = LC ready (in data transfer mode). | 90805 | X.25 Reset Confirmation received without Reset sent (from <Node X.25 Address>, line <Port Number>, info=<Info>) | warning |
| 03_26: An unexpected X.25 packet was received after a Reset was received; info indicates: byte5 of frame. | 90806 | Unexpected packet received after X.25 Reset (from <Node X.25 Address>, line <Port Number>, info=<Info>) | warning |
| 03_27: Two consecutive X.25 Interrupt packets were received; a Reset was sent. | 90807 | Consecutive X.25 Interrupt packets received (from <Node X.25 Address>, line <Port Number>) | warning |
| 03_28: An X.25 Interrupt Confirmation was received without an Interrupt packet having been sent. | 90808 | X.25 Interrupt Confirmation received without Interrupt (from <Node X.25 Address>, line <Port Number>) | warning |
| 03_29: An X.25 Data packet was received outside the sequence window; a Reset was sent. | 90809 | X.25 Data packet received outside sequence window (from <Node X.25 Address>, line <Port Number>) | warning |
| 03_2A: An X.25 Data packet was received out of sequence; a Reset was sent. | 90810 | X.25 Data packet received out of sequence (from <Node X.25 Address>, line <Port Number>) | warning |
| 03_2B: An X.25 Data Packet with an incorrect N(S) was received. | 90811 | X.25 Packet with incorrect N(S) received (from <Node X.25 Address>, line <Port Number>) | warning |
| 03_2C: An X.25 REJ packet was received. | 90812 | X.25 REJ packet received (from <Node X.25 Address>, line <Port Number>) | normal |
| 03_2D: An X.25 Reset was sent, now waiting for a response; | 90813 | Awaiting response to Reset on X.25 (from <Node X.25 Address>, line <Port Number>) | normal |
| 03_2E: An X.25 RNR packet was received; Data Packet transmission is blocked until an RR is received. | 90814 | X.25 RNR packet received, send blocked (from <Node X.25 Address>, line <Port Number>) | normal |
| 03_2F: An invalid X.25 packet was received via a PVC; the packet is ignored; info indicates: byte3 of frame, byte4 of frame. | 90815 | Invalid X.25 packet received via PVC (from <Node X.25 Address>, line <Port Number>, info=<Info>) | warning |
| 03_30: An X.25 frame was repeated N times without acknowledgement; info indicates: frame level state. | 90816 | X.25 frame retried N times without ACK (from <Node X.25 Address>, line <Port Number>, info=<Info>) | warning |
| 03_31: An unexpected X.25 frame was received with the Frame Level down; info indicates: frame level state, byte1 of frame, byte2 of frame, byte3 of frame. | 90817 | Unexpected X.25 frame with Frame Level down (from <Node X.25 Address>, line <Port Number>, info=<Info>) | warning |
| 03_32: An unexpected X.25 frame was received while the Frame Level was in the DISCONNECTING state; info indicates: frame level state, byte1 of frame, byte2 of frame, byte3 of frame. | 90818 | Unexpected X.25 frame with Frame Level disconnecting (from <Node X.25 Address>, line <Port Number>, info=<Info>) | warning |
| 03_33: An unexpected X.25 frame was received while the Frame Level was in the CONNECTING state; info indicates: frame level state, byte1 of frame, byte2 of frame. | 90819 | Unexpected X.25 frame with Frame Level connecting (from <Node X.25 Address>, line <Port Number>, info=<Info>) | warning |
| 03_35: An X.25 Diagnostic packet was received; a Clear was sent; info indicates: byte6 of frame, byte7 of frame, byte8 of frame, byte9 of frame. | 90821 | Reception of an X.25 Diagnostic packet (from <Node X.25 Address>, line <Port Number>, info=<Info>) | normal |
| 03_36: An X.25 Reset packet was received with reason unknown; info indicates: Logical Channel number, Reset diagnostic. | 90822 | X.25 Reset received with reason unknown (from <Node X.25 Address>, line <Port Number>, info=<Info>) | warning |
| 03_37: An X.25 Reset packet was sent with reason unknown; info indicates: Logical Channel number, Reset diagnostic. | 90823 | X.25 Reset sent with reason unknown (from <Node X.25 Address>, line <Port Number>, info=<Info>) | warning |
| 04_00: The Logical Link Level is down; all VC traffic is blocked; line = 0-35 for physical link, line = 36-41 for inter-unit link, line = 50-55 for inter-module link. | 91024 | Link Level down (from <Node X.25 Address>, line <Port Number>) | major |
| 04_01: The Logical Link Level is up; all VC traffic is enabled; line = 0-35 for physical link, line = 36-41 for inter-unit link, line = 50-55 for inter-module link. | 91025 | Link Level up (from <Node X.25 Address>, line <Port Number>) | normal |
| 05_01: The I/O controller has lost one or more frames. | 91281 | Loss of frames in I/O controller (from <Node X.25 Address>, line <Port Number>) | minor |
| 05_02: Line signals changed; Modem: circuit 117 (StandBy) off, terminal: circuit 141 (LL) off. | 91282 | Line signals 117/141 off (from <Node X.25 Address>, line <Port Number>) | normal |
| 05_03: Line signals changed; Modem: circuit 117 (StandBy) on, terminal: circuit 141 (LL) on. | 91283 | Line signals 117/141 on (LocalLoopback) (from <Node X.25 Address>, line <Port Number>) | normal |
| 05_81: The I/O controller lost one or more receive frames; info indicates: number of frames lost. | 91409 | Loss of receive frames in I/O controller (from <Node X.25 Address>, line <Port Number>, info=<Info>) | minor |
| 05_82: Line signals changed; Modem: circuit 109 (DCD) on, terminal: circuit 105 (RTS) on. | 91410 | Line signals 109/105 on (from <Node X.25 Address>, line <Port Number>) | normal |
| 05_83: Line signals changed; Modem: circuit 109 (DCD) off, terminal: circuit 105 (RTS) off. | 91411 | Line signals 109/105 off (from <Node X.25 Address>, line <Port Number>) | normal |
| 05_85: Line signals changed; Modem: circuit 106 (CTS) off, terminal: circuit 108 (DTR) off. | 91413 | Line signals 106/108 off (from <Node X.25 Address>, line <Port Number>) | normal |
| 05_86: Line signals changed; Modem: circuit 107 (DSR) off, terminal: circuit 111 (RateSelect) off. | 91414 | Line signals 107/111 off (from <Node X.25 Address>, line <Port Number>) | normal |
| 05_87: An ABORT was received on a line. | 91415 | ABORT received (from <Node X.25 Address>, line <Port Number>) | normal |
| 05_88: A MALFUNCTION was received on a line. | 91416 | MALFUNCTION received at physical level (from <Node X.25 Address>, line <Port Number>) | minor |
| 05_8C: A frame was received with a CRC error; the frame is ignored. | 91420 | CRC error on Receive frame (from <Node X.25 Address>, line <Port Number>) | minor |
| 05_90: Line signals changed; Modem: circuit 141 (LL) off, terminal: circuit 125 (RI) off. | 91424 | Line signals 141/125 off (from <Node X.25 Address>, line <Port Number>) | normal |
| 05_91: Line signals changed; Modem: circuit 141 (LL) on, terminal: circuit 125 (RI) on. | 91425 | Line signals 141/125 on (from <Node X.25 Address>, line <Port Number>) | normal |
| 05_92: Line signals changed; Modem: circuit 142 (TM) off, terminal: circuit 140 (Test) off. | 91426 | Line signals 142/140 off (from <Node X.25 Address>, line <Port Number>) | normal |
| 05_93: Line signals changed; Modem: circuit 142 (TM) on, terminal: circuit 140 (Test) on. | 91427 | Line signals 142/140 on (from <Node X.25 Address>, line <Port Number>) | normal |
| 05_95: Line signals changed; Modem: circuit 106 (CTS) on, terminal: circuit 108 (DTR) on. | 91429 | Line signals 106/108 on (from <Node X.25 Address>, line <Port Number>) | normal |
| 05_96: Line signals changed; Modem: circuit 107 (DSR) on, terminal: circuit 111 (RateSelect) on. | 91430 | Line signals 107/111 on (from <Node X.25 Address>, line <Port Number>) | normal |
| 05_BF: An incomplete Byte was received; the line is taken out of service. | 91471 | Incomplete Byte received (from <Node X.25 Address>, line <Port Number>) | minor |
| 05_FD: Loss of sync flags occurred. | 91533 | Loss of sync flags (from <Node X.25 Address>, line <Port Number>) | warning |
| 05_FE: Restoral of sync flags occurred. | 91534 | Restoral of sync flags (from <Node X.25 Address>, line <Port Number>) | normal |
| 06_97: An attempt to activate an LSCP (Low Speed Computer Port) failed; the next LCSP defined for the subscriber will be tried, if all have been tried, the Call fails. | 91687 | LSCP activation failure on Async (from <Node X.25 Address>, line <Port Number>) | warning |
| 06_98: The terminal is not set to the correct Baud rate or is not set to the correct number of Stopbits; the received character is ignored. | 91688 | Incorrect baud rate or stop bits on Async (from <Node X.25 Address>, line <Port Number>) | minor |
| 06_99: The Autobaud procedure detected a rate higher than that supported by Autobaud (38.4Kbps); the line has not been Autobauded. | 91689 | Excess rate detected on Async (from <Node X.25 Address>, line <Port Number>) | minor |
| 06_9A: The terminal dropped circuit 105 (RTS) for more than 200ms indicating disconnection; any Call in progress is cleared, the terminal is taken out of service. | 91690 | Terminal disconnected after 200ms on Async (from <Node X.25 Address>, line <Port Number>) | warning |
| 06_9C: The terminal raised circuit 105 (RTS); if it is set for a fixed rate, it is activated immediately, otherwise the automatic rate detection sequence is awaited (Autobaud). | 91692 | Terminal connected on Async (from <Node X.25 Address>, line <Port Number>) | normal |
| 06_9D: The requested Videotex service is not available, eg: error correction protocol or modem reversal); the Call is cleared. | 91693 | Videotex service not available on Async (from <Node X.25 Address>, line <Port Number>) | warning |
| 06_9E: The automatic data rate detection sequence (Autobaud) detected a valid rate from the attached terminal; the terminal is activated. | 91694 | Terminal data rate recognized on Async (from <Node X.25 Address>, line <Port Number>) | normal |
| 06_9F: The automatic data rate detection sequence (Autobaud) received an invalid rate from the attached terminal; the Call is terminated if PSTN type, otherwise a valid sequence is awaited. | 91695 | Terminal data rate not recognized on Async (from <Node X.25 Address>, line <Port Number>) | warning |
| 07_9B: An erroneous command was entered at the terminal; the "ERROR" message is sent to the terminal and Data Mode is re-entered if a Call is active; info indicates: last character received. | 91947 | Erroneous terminal command (from <Node X.25 Address>, line <Port Number>, info=<Info>) | normal |
| 08_92: The current Call in progress is dropped; a clear message is sent (if the profile allows it), for an LSCP line, circuit 105 (RTS) is dropped, for a PSTN line, the check time-out is reset. | 92194 | Call in progress cut off (from <Node X.25 Address>, line <Port Number>) | warning |
| 08_93: A Call setup was attempted from a terminal managed by the FastPADmp; a Call Block is sent and the terminal enters Data Mode when a Call Confirmation is received. | 92195 | Call attempt via FastPADmp (from <Node X.25 Address>, line <Port Number>) | normal |
| 08_9D: An X.29 message was received; the appropriate response and action are generated. | 92205 | X.29 message received (from <Node X.25 Address>, line <Port Number>) | normal |
| 08_A0: The Call setup time on a PSTN line took too long. | 92208 | Phone line: call setup timeout (from <Node X.25 Address>, line <Port Number>) | warning |
| 08_A1: Command entry was attempted before a Call has been setup. | 92209 | Phone line: command entry without Call (from <Node X.25 Address>, line <Port Number>) | warning |
| 08_A2: Too many command entries were attempted without a Call setup. | 92210 | Too many commands without Call (from <Node X.25 Address>, line <Port Number>) | warning |
| 08_A3: Minitel turnaround succeeded; data rate set to: 1200bps (receive) / 75bps (transmit). | 92211 | Minitel turnaround succeeded (from <Node X.25 Address>) | normal |
| 08_A4: Minitel reverse turnaround succeeded; data rate set to: 75bps (receive) / 1200bps (transmit). | 92212 | Minitel reverse turnaround succeeded (from <Node X.25 Address>) | normal |
| 08_A7: Activation of Error Correction Protocol - Normal Mode (ECPN) succeeded. | 92215 | Activation of ECPN succeeded (from <Node X.25 Address>) | normal |
| 08_A8: Activation of Error Correction Protocol - Normal Mode (ECPN) failed after 8 attempts. | 92216 | Activation of ECPN failed (from <Node X.25 Address>) | warning |
| 08_A9: Inactivation of Error Correction Protocol - Normal Mode (ECPN) succeeded. | 92217 | Inactivation of ECPN succeeded (from <Node X.25 Address>) | normal |
| 08_AA: Inactivation of Error Correction Protocol - Normal Mode (ECPN) failed after 8 attempts. | 92218 | Inactivation of ECPN failed (from <Node X.25 Address>) | warning |
| 08_AB: An ECPN re-transmission request was received. | 92219 | Received ECPN re-transmission request (from <Node X.25 Address>) | normal |
| 08_AC: Activation of Error Correction Protocol - Inverse Mode (ECPI) succeeded. | 92220 | Activation of ECPI succeeded (from <Node X.25 Address>) | normal |
| 08_AD: Inactivation of Error Correction Protocol - Inverse Mode (ECPI) succeeded. | 92221 | Inactivation of ECPI succeeded (from <Node X.25 Address>) | normal |
| 08_AE: An ECPN re-transmission request was transmitted. | 92222 | Transmitted ECPN re-transmission request (from <Node X.25 Address>) | normal |
| 09_00: An SDLC Frame with an unknown address was received; the frame is ignored; info indicates: address field. | 92304 | Unknown address in SDLC Frame (from <Node X.25 Address>, line <Port Number>, info=<Info>) | minor |
| 09_01: An SDLC Frame with an invalid length was received; the frame is ignored; info indicates: frame length, address field, command field. | 92305 | Invalid length in SDLC Frame (from <Node X.25 Address>, line <Port Number>, info=<Info>) | minor |
| 09_03: An SDLC Frame with an unknown command was received; an FRMR is sent; info indicates: address field, command field. | 92307 | Unknown command in SDLC Frame (from <Node X.25 Address>, line <Port Number>, info=<Info>) | warning |
| 09_04: An SDLC Frame with an unknown response was received; the frame is ignored; info indicates: address field, command field. | 92308 | Unknown response in SDLC Frame (from <Node X.25 Address>, line <Port Number>, info=<Info>) | minor |
| 09_0C: An SDLC Frame with an incorrect N(R) was received; a Clear VC is sent to the remote, an FRMR is sent to the FEP; info indicates: address field, command field. | 92316 | Incorrect N(R) in SDLC Frame (from <Node X.25 Address>, line <Port Number>, info=<Info>) | warning |
| 09_0E: An SDLC Frame out of sequence or with duplicate sequence was received; the frame is ignored; info indicates: address field, command field. | 92318 | Sequence error or duplicate SDLC frame (from <Node X.25 Address>, line <Port Number>, info=<Info>) | minor |
| 09_0F: An SDLC Frame was received outside the sequence window; the frame is ignored; info indicates: address field, command field. | 92319 | SDLC Frame outside window (from <Node X.25 Address>, line <Port Number>, info=<Info>) | minor |
| 09_10: An SDLC FRMR frame was received on the Remote side only; the Transmit and Receive counters are reset, an SNRM is sent, the VC is Cleared; info indicates: address field, command field. | 92320 | FRMR SDLC Frame Remote side only (from <Node X.25 Address>, line <Port Number>, info=<Info>) | warning |
| 09_11: An SDLC Frame encountered N2 retries in the data transfer phase; the frame is re-sent; info indicates: address field, command field. | 92321 | Data transfer retries exceeded on SDLC (from <Node X.25 Address>, line <Port Number>, info=<Info>) | warning |
| 09_12: An SDLC Frame encountered N2 retries in the test phase; the frame is re-sent; info indicates: address field, command field. | 92322 | Test phase retries exceeded on SDLC (from <Node X.25 Address>, line <Port Number>, info=<Info>) | warning |
| 09_13: An SDLC Frame encountered N2 retries in the ID phase; frame is re-sent; info indicates: address field, command field. | 92323 | ID phase retries exceeded on SDLC (from <Node X.25 Address>, line <Port Number>, info=<Info>) | warning |
| 09_14: An SDLC Frame encountered N2 retries in the mode positioning phase; the frame is re-sent; info indicates: address field, command field. | 92324 | Mode positioning phase retries exceeded on SDLC (from <Node X.25 Address>, line <Port Number>, info=<Info>) | warning |
| 09_15: An SDLC Frame encountered N2 retries in the DISC phase; the frame is re-sent; info indicates: address field, command field. | 92325 | DISC retries exceeded on SDLC (from <Node X.25 Address>, line <Port Number>, info=<Info>) | warning |
| 09_16: A T1 timeout occured on an SDLC Frame from a T2.1 cluster in the Connection phase; polling continues; info indicates: address field, command field. | 92326 | Connection T1 timeout on SDLC (from <Node X.25 Address>, line <Port Number>, info=<Info>) | warning |
| 09_17: A T1 timeout occured on an SDLC Frame during SNRM polling; polling continues; info indicates: address field, command field. | 92326 | SNRM polling T1 timeout on SDLC (from <Node X.25 Address>, line <Port Number>, info=<Info>) | warning |
| 09_31: An SDLC Frame was received on a circuit in the non-established state; the frame is ignored; info indicates: address field, command field. | 92353 | SDLC Frame error received on VC not established (from <Node X.25 Address>, line <Port Number>, info=<Info>) | minor |
| 09_32: An SDLC UA Frame was received on a remote circuit in the non-established state; the X.25 level is Cleared, a DISC is sent at Frame level; info indicates: address field, command field. | 92354 | SDLC UA Frame error received on remote circuit (from <Node X.25 Address>, line <Port Number>, info=<Info>) | warning |
| 09_33: An SDLC UA Frame was received on a local circuit in the non-established state; X.25 level is Cleared, a DISC is sent at Frame level; info indicates: address field, command field. | 92355 | SDLC UA Frame error received on local circuit (from <Node X.25 Address>, line <Port Number>, info=<Info>) | warning |
| 09_35: An SDLC XID Frame was received on a circuit; the X.25 level is Cleared, DISC is sent at Frame level; info indicates: address field, command field. | 92357 | XID Frame error received on SDLC (from <Node X.25 Address>, line <Port Number>, info=<Info>) | warning |
| 09_80: An SDLC VC encountered circuit 108 (DTR) drop; the VC is Cleared; info indicates: address field, command field. | 92432 | Line signal 108 (DTR) drop caused Clear on SDLC (from <Node X.25 Address>, line <Port Number>, info=<Info>) | normal |
| 09_81: A Call request was transmitted on an SDLC line; info indicates: address field, logical channel. | 92433 | Call request sent on SDLC (from <Node X.25 Address>, line <Port Number>, info=<Info>) | normal |
| 09_82: A Clear was transmitted on an SDLC line; info indicates: address field, logical channel. | 92434 | Clear sent on SDLC (from <Node X.25 Address>, line <Port Number>, info=<Info>) | normal |
| 09_83: A Call was received on an SDLC line; a Call Confirmation is sent; info indicates: address field, logical channel. | 92435 | Call received on SDLC (from <Node X.25 Address>, line <Port Number>, info=<Info>) | normal |
| 09_84: An invalid Call was received on an SDLC line while in FRONT mode. | 92436 | Invalid Call in SDLC FRONT mode (from <Node X.25 Address>, line <Port Number>) | warning |
| 09_85: An SDLC line encountered circuit 108 (DTR) drop; SNRM polling is started. | 92437 | Line signal 108 (DTR) drop caused SNRM on SDLC (from <Node X.25 Address>, line <Port Number>) | normal |
| 09_86: A BackUp Call packet was sent on an SDLC line. | 92438 | BackUp Call sent on SDLC (from <Node X.25 Address>, line <Port Number>) | normal |
| 09_87: A Clear Confirmation was received on an SDLC line; info indicates: address field, logical channel. | 92439 | Clear Confirmation on SDLC (from <Node X.25 Address>, line <Port Number>, info=<Info>) | normal |
| 09_88: A Call Confirmation was received on an SDLC line; info indicates: address field, logical channel. | 92440 | Call Confirmation on SDLC (from <Node X.25 Address>, line <Port Number>, info=<Info>) | normal |
| 09_89: Call retries on a Backup SDLC line were exhausted; the Call is Cleared. | 92441 | Backup Call retries exhausted on SDLC (from <Node X.25 Address>, line <Port Number>) | warning |
| 09_8A: A Clear was received on an SDLC line; a Call Request is sent; info indicates: address field, logical channel. | 92442 | Clear on SDLC (from <Node X.25 Address>, line <Port Number>, info=<Info>) | normal |
| 09_8B: Call retries on an SDLC line were exhausted; the Call is Cleared; info indicates: address field, logical channel. | 92443 | Call retries exhausted on SDLC (from <Node X.25 Address>, line <Port Number>, info=<Info>) | warning |
| 09_8C: A Call Request with an error was received on an SLDC line; code C2 was not found in Byte 0 of the Call Request data field; the Call is Cleared; info indicates: logical channel. | 92444 | Protocol Error in Call on SDLC (from <Node X.25 Address>, line <Port Number>, info=<Info>) | warning |
| 09_8D: An unexpected PSH-LLC packet was received on an SDLC line; the VC is Cleared; info indicates: address field, logical channel. | 92445 | Unexpected PSH-LLC on SDLC (from <Node X.25 Address>, line <Port Number>, info=<Info>) | warning |
| 09_8E: An unexpected frame was received on an SDLC line; the VC is Cleared; info indicates: address field, logical channel. | 92446 | Unexpected Frame on SDLC (from <Node X.25 Address>, line <Port Number>, info=<Info>) | warning |
| 09_8F: A sequence error was detected in a PSH-LLC packet received on an SLDC line; the VC is Cleared; info indicates: address field, logical channel. | 92447 | Sequence error in PSH-LLC on SDLC (from <Node X.25 Address>, line <Port Number>, info=<Info>) | warning |
| 09_90: The state of a VC switched to Data Transfer on an SDLC line; info indicates: address field, logical channel. | 92448 | Switched to Data Transfer on SDLC (from <Node X.25 Address>, line <Port Number>, info=<Info>) | normal |
| 09_91: An unexpected packet was received while in Data Transfer state (PSH-LLC) on an SDLC line; the VC is Cleared or the packet is ignored, see C12RxxP38 setting; info indicates: address field, logical channel. | 92449 | Unexpected packet in Data Transfer on SDLC (from <Node X.25 Address>, line <Port Number>, info=<Info>) | warning |
| 09_92: A "Disable in outgoing transmission state" was received on an SDLC line. | 92450 | Disable Send state in SLDC (from <Node X.25 Address>, line <Port Number>) | normal |
| 09_93: A "Disable in current receive state" was received on an SDLC line. | 92451 | Disable Receive state in SDLC (from <Node X.25 Address>, line <Port Number>) | normal |
| 09_94: A "Disable in Blocked state" was received on an SDLC line. | 92452 | Disable in Blocked state on SDLC (from <Node X.25 Address>, line <Port Number>) | normal |
| 09_95: A T1 transmission timeout occurred on an SDLC line; info indicates: address field. | 92453 | Transmission timeout on SDLC (from <Node X.25 Address>, line <Port Number>, info=<Info>) | warning |
| 09_96: An I-Frame was received during send on an SDLC line; the frame is ignored; info indicates: frame length, address field, command field, byte1 of data. | 92454 | I-Frame during send on SDLC (from <Node X.25 Address>, line <Port Number>, info=<Info>) | minor |
| 09_97: An RR frame with P/F=0 was received during send on an SDLC line; the frame is ignored; info indicates: address field, command field. | 92455 | RR with P/F=0 during send on SDLC (from <Node X.25 Address>, line <Port Number>, info=<Info>) | minor |
| 09_98: An RR frame with P/F=1 was received during send on an SDLC line; the frame is ignored; info indicates: address field, command field. | 92456 | RR with P/F=1 during send on SDLC (from <Node X.25 Address>, line <Port Number>, info=<Info>) | minor |
| 09_99: An RNR frame with P/F=0 was received during send on an SDLC line; the frame is ignored; info indicates: address field, command field. | 92457 | RNR with P/F=0 during send on SDLC (from <Node X.25 Address>, line <Port Number>, info=<Info>) | minor |
| 09_9A: An RNR frame with P/F=1 was received during send on an SDLC line; the frame is ignored; info indicates: address field, command field. | 92458 | RNR with P/F=1 during send on SDLC (from <Node X.25 Address>, line <Port Number>, info=<Info>) | minor |
| 09_9B: An REJ frame with P/F=0 was received during send on an SDLC line; the frame is ignored; info indicates: address field, command field. | 92459 | REJ with P/F=0 during send on SDLC (from <Node X.25 Address>, line <Port Number>, info=<Info>) | minor |
| 09_9C: An REJ frame with P/F=1 was received during send on an SDLC line; the frame is ignored; info indicates: address field, command field. | 92460 | REJ with P/F=1 during send on SDLC (from <Node X.25 Address>, line <Port Number>, info=<Info>) | minor |
| 09_9D: A packet with a 2nd PSH byte of unknown command type was received on an SDLC line; the packet is ignored; info indicates: address field, logical channel. | 92461 | Packet with 2nd PSH on SDLC (from <Node X.25 Address>, line <Port Number>, info=<Info>) | minor |
| 09_9E: A "Transmit Report" (TR) message was received while in receive status on an SDLC line; the frame is ignored; info indicates: address field. | 92462 | Transmit Report message in receive state on SDLC (from <Node X.25 Address>, line <Port Number>, info=<Info>) | minor |
| 09_9F: A "Transmit Report" (TR) message was received while in blocked status on an SDLC line; the frame is ignored; info indicates: address field. | 92463 | Transmit Report message in blocked state on SDLC (from <Node X.25 Address>, line <Port Number>, info=<Info>) | minor |
| 09_C0: A QUA was received during Data Transfer on an SDLC line; the packet is ignored; info indicates: address field, logical channel. | 92496 | QUA during Data Transfer on SDLC (from <Node X.25 Address>, line <Port Number>, info=<Info>) | minor |
| 09_C1: An unknown packet was received during Data Transfer state (QLLC) on an SDLC line; a Clear is sent or the packet is ignored, see C12RxxP38 setting; info indicates: address field, logical channel. | 92497 | Unknown packet in Data Transfer on SDLC (from <Node X.25 Address>, line <Port Number>, info=<Info>) | warning |
| 09_C2: An unknown command packet was received on an SDLC line; the packet is ignored; info indicates: address field, logical channel. | 92498 | Command packet unknown on SDLC (from <Node X.25 Address>, line <Port Number>, info=<Info>) | minor |
| 09_CD: An unexpected QLLC packet was received on an SDLC line; the VC is Cleared; info indicates: address field, logical channel. | 92509 | Unexpected QLLC packet on SDLC (from <Node X.25 Address>, line <Port Number>, info=<Info>) | warning |
| 09_CE: An unexpected QLLC packet was received on an SDLC line, 2nd encoded event; the VC is Cleared; info indicates: address field, logical channel. | 92510 | Unexpected QLLC packet-2 on SDLC (from <Node X.25 Address>, line <Port Number>. info=<Info>) | warning |
| 09_CF: The QLLC protocol requested a Clear on an SDLC line; the VC is Cleared; info indicates: address field, logical channel. | 92511 | QLLC Clear on SDLC (from <Node X.25 Address>, line <Port Number>, info=<Info>) | warning |
| 09_D0: A request to establish a VC was received from a remote node; a Call Request is sent. | 92512 | Remote request for VC on SDLC (from <Node X.25 Address>, line <Port Number>) | normal |
| 09_D1: A requested VC was established on an SDLC line. | 92513 | VC established on SDLC (from <Node X.25 Address>, line <Port Number>) | normal |
| 09_D2: An XID for a Cluster controller was received on an SDLC line; the appropriate QLLC protocol element is sent; info indicates: logical channel. | 92514 | Cluster XID on SDLC (from <Node X.25 Address>, line <Port Number>, info=<Info>) | normal |
| 0A_00: An ABORT with cause unknown was received on a VIP line. | 92560 | ABORT received for unknown cause on VIP (from <Node X.25 Address>, line <Port Number>) | warning |
| 0A_01: An X.25 network RESET was received for an associated VIP line; a RESET is sent and the VIP VC is Cleared. | 92561 | X.25 RESET from network on VIP (from <Node X.25 Address>, line <Port Number>) | normal |
| 0A_02: An ABORT due to frame too long was received on a VIP line; the frame is ignored, sequence is restarted. | 92562 | ABORT received for frame too long on VIP (from <Node X.25 Address>, line <Port Number>) | minor |
| 0A_03: An ABORT due to reception time out was received on a VIP line; the frame is ignored, sequence is restarted. | 92563 | ABORT received for receive time out on VIP (from <Node X.25 Address>, line <Port Number>) | minor |
| 0A_04: An ABORT due to a VRC error was received on a VIP line; the frame is ignored, sequence is restarted. | 92564 | ABORT received for VRC error on VIP (from <Node X.25 Address>, line <Port Number>) | minor |
| 0A_05: An ABORT due to an LRC error was received on a VIP line; the frame is ignored, sequence is restarted. | 92565 | ABORT received for LRC error on VIP (from <Node X.25 Address>, line <Port Number>) | minor |
| 0A_06: An Abort due to not being available to X.25 level was received on a VIP line; selectively cleared. | 92566 | ABORT received for not available to X.25 on VIP (from <Node X.25 Address>, line <Port Number>) | warning |
| 0A_07: An Abort due to a lost character at the Handler level was received on a VIP line. | 92567 | ABORT received for lost character on VIP (from <Node X.25 Address>) | warning |
| 0A_08: An Abort was transmitted for an unknown cause on a VIP line. | 92568 | ABORT transmitted for cause unknown on VIP (from <Node X.25 Address>, line <Port Number>) | warning |
| 0A_0E: A protocol violation occurred on a VIP line. | 92574 | Protocol violation on VIP (from <Node X.25 Address>) | warning |
| 0A_0F: An event was prohibited on a VIP line at the physical level. | 92575 | Event prohibited in VIP physical (from <Node X.25 Address>) | warning |
| 0A_11: A NAK screen was received on a VIP line; immediate re-transmission occurs. | 92577 | NAK screen on VIP (from <Node X.25 Address>, line <Port Number>) | warning |
| 0A_12: A BSY screen was received on a VIP line; re-transmission is delayed. | 92578 | BSY screen on VIP (from <Node X.25 Address>, line <Port Number>) | warning |
| 0A_13: A PGOF screen was received on a VIP line; re-transmission is delayed. | 92579 | PGOF screen on VIP (from <Node X.25 Address>, line <Port Number>) | warning |
| 0A_14: A NAK printer message was received on a VIP line; immediate re-transmission occurs. | 92580 | NAK printer on VIP (from <Node X.25 Address>, line <Port Number>) | warning |
| 0A_15: A BSY printer message was received on a VIP line; re-transmission is delayed. | 92581 | BSY printer on VIP (from <Node X.25 Address>, line <Port Number>) | warning |
| 0A_16: A NA (Not Accepted) printer message was received on a VIP line; re-transmission is delayed. | 92582 | NA printer on VIP (from <Node X.25 Address>, line <Port Number>) | warning |
| 0A_17: Re-initialization of VIP equipment occurred. | 92583 | Re-initialization of VIP equipment (from <Node X.25 Address>, line <Port Number>) | warning |
| 0A_18: Too many NAKs were received on a VIP line; the screen message is discarded. | 92584 | Too many NAKs on VIP (from <Node X.25 Address>) | warning |
| 0A_19: Too many NAKs or NAs were received from a printer on a VIP line; all printer messages are discarded. | 92585 | Too many NAKs or NAs from printer on VIP (from <Node X.25 Address>) | warning |
| 0A_1F: A protocol violation at the logical level occurred on a VIP line; the line is Reset. | 92591 | Protocol violation on VIP (from <Node X.25 Address>) | warning |
| 0A_21: A Connection was issued to an X.25 network (Call) on a VIP line; Call is accepted if station is polled, otherwise Call is refused and Clear is sent. | 92593 | Connection issued X.25 network on VIP (from <Node X.25 Address>, line <Port Number>) | normal |
| 0A_22: A Disconnection was issued on an X.25 network (Clear) on a VIP line; the VIP connection is Cleared, re-connect on the controller side is attempted. | 92594 | Disconnection issued X.25 network on VIP (from <Node X.25 Address>, line <Port Number>) | normal |
| 0A_23: A Connection was issued by VIP; a Call packet is sent. | 92595 | Connection issued VIP controller (from <Node X.25 Address>, line <Port Number>) | normal |
| 0A_24: A Disconnection was issued by VIP on: controller: no response to polling, host: no reception to polling frame. | 92596 | Disconnection issued VIP controller (from <Node X.25 Address>, line <Port Number>) | normal |
| 0A_25: An unknown address was received on a VIP line. | 92597 | Unknown VIP address (from <Node X.25 Address>, line <Port Number>) | warning |
| 0A_2F: An event was prohibited in a VIP connection. | 92607 | Event prohibited in VIP connection (from <Node X.25 Address>) | warning |
| 0A_30: Data flow toward the host is blocked; the I/O block is deleted; all messages are discarded; info indicates: station number. | 92608 | Flow toward host blocked on VIP (from <Node X.25 Address>, line <Port Number>, info=<Info>) | warning |
| 0A_31: A host response timer expired on a VIP line; the I/O block flow is re-transmitted to the host info indicates: station number. | 92609 | Response timeout on VIP (from <Node X.25 Address>, line <Port Number>, info=<Info>) | warning |
| 0A_40: A Reset was received for an unknown cause on a VIP line. | 92624 | Reset for unknown cause on VIP (from <Node X.25 Address>, line <Port Number>) | warning |
| 0B_00: A Call is initiated on a FR, T.VIP or BSC line; awaiting Call Confirmation. | 92816 | Initiating a Call on FR/TVIP/BSC (from <Node X.25 Address>, line <Port Number>) | normal |
| 0B_01: A Call Request was refused due to unknown equipment or node on a FR, T.VIP or BSC line; a Clear is sent. | 92817 | Call refused, unknown node on FR/TVIP/BSC (from <Node X.25 Address>, line <Port Number>) | warning |
| 0B_02: Communication is Cleared on a FR, T.VIP or BSC line; awaiting Clear Confirmation. | 92818 | Communication cleared on FR/TVIP/BSC (from <Node X.25 Address>, line <Port Number>) | normal |
| 0B_03: Partially transmitted messages were aborted on FR, T.VIP or BSC line. | 92819 | Messages aborted on FR/TVIP/BSC (from <Node X.25 Address>, line <Port Number>) | warning |
| 0B_04: A RESET was received on a FR, T.VIP or BSC line; any partial messages are removed from the receive queue, the DLC sub-assembly state is reset. | 92820 | RESET received on FR/TVIP/BSC (from <Node X.25 Address>, line <Port Number>) | normal |
| 0B_05: A RESET was sent on a FR, T.VIP or BSC line; awaiting receipt of a RESET. | 92821 | RESET sent on FR/TVIP/BSC (from <Node X.25 Address>, line <Port Number>) | normal |
| 0B_15: A VC Call is initiated on the controller side on a FR, T.VIP or BSC line; Call packet contains polled VIP address. | 92837 | VC Call initiated on controller side on FR/TVIP/BSC (from <Node X.25 Address>, line <Port Number>) | normal |
| 0B_16: A VC Call was refused on the host side on a FR, T.VIP or BSC line due to: - VIP node not polled by host or - VIP node not configured; the VC is Cleared. | 92838 | VC Call refused on host side on FR/TVIP/BSC (from <Node X.25 Address>, line <Port Number>) | warning |
| 0B_21: A VC Call is intiated on the host side on a FR, T.VIP or BSC line. | 92849 | VC Call initiated on host side on FR/TVIP/BSC (from <Node X.25 Address>, line <Port Number>) | normal |
| 0B_22: A VC Call was refused on the controller side on a FR, T.VIP or BSC line. | 92850 | VC Call refused on controller side on FR/TVIP/BSC (from <Node X.25 Address>, line <Port Number>) | warning |
| 0C_00: A Station requested a Disconnect on a DLC or BSC line; the VC is Cleared; info indicates: station connection state, see Management Manual Appendix B. | 93072 | Station Disconnect on DLC/BSC (from <Node X.25 Address>, info=<Info>) | normal |
| 0C_01: A Station requested a Connect on a DLC or BSC line, when the controller has not been previously polled; the VC is Initiated. | 93073 | Station Connect on DLC/BSC (from <Node X.25 Address>) | normal |
| 0C_02: The line is out of service on a DLC or BSC line, OR a controller or station is disconnected; info indicates: detailed cause, see Management Manual Appendix B; for: line down: communications to all stations is Cleared, controller disconnect: all stations on this controller are Cleared, station disconnect: this station is Cleared. | 93074 | Line down on DLC/BSC (from <Node X.25 Address>, info=<Info>) | major |
| 0C_03: Station Connect issued while station is Connecting on a DLC or BSC line; the Station Connect request is ignored. | 93075 | TPAD collision on DLC/BSC (from <Node X.25 Address>) | warning |
| 0C_04: A Station Connect occurred on a DLC/BSC line, caused by recovery on the line in progress; info indicates: controller and station addresses, see Management Manual Appendix B; | 93076 | Recovery of Station Connect on DLC/BSC (from <Node X.25 Address>, info=<Info>) | normal |
| 0C_05: A Disconnect of the controller station on a DLC or BSC line occurred; see Management Manual Appendix B; | 93077 | Disconnect the controller on DLC/BSC (from <Node X.25 Address>) | normal |
| 0C_06: A Disconnect of a non-controller station on a DLC or BSC line occurred; the Call is refused; see Management Manual Appendix B; | 93078 | Disconnect non-controller on DLC/BSC (from <Node X.25 Address>) | normal |
| 0C_18: A Disconnect from the network was received on a DLC or BSC line; see Management Manual Appendix B; | 93096 | Disconnect from network on DLC/BSC (from <Node X.25 Address>) | normal |
| 0C_19: A Connect from the network was received on a DLC or BSC line; see Management Manual Appendix B; | 93097 | Connect from network on DLC/BSC (from <Node X.25 Address>) | normal |
| 0C_20: Unknown data was received on a DLC or BSC line; the message is rejected; see Management Manual Appendix B; | 93104 | Unknown data on DLC/BSC (from <Node X.25 Address>) | warning |
| 0C_21: An unknown control character was received on a DLC or BSC line; see Management Manual Appendix B; | 93105 | Unknown control character on DLC/BSC (from <Node X.25 Address>) | warning |
| 0C_22: An unknown station or unknown CA-DA was detected on a DLC or BSC line; the message is ignored; see Management Manual Appendix B; | 93106 | Unknown station on DLC/BSC (from <Node X.25 Address>) | warning |
| 0C_23: An unknown controller was detected on a DLC or BSC line; see Management Manual Appendix B; | 93107 | Unknown controller on DLC/BSC (from <Node X.25 Address>) | warning |
| 0C_24: An unknown CA-DA/BCC parity error (single block) occurred on a DLC or BSC line; EOT is transmitted; see Management Manual Appendix B; | 93108 | Unknown CA-DA/BCC parity error on DLC/BSC (from <Node X.25 Address>) | warning |
| 0C_25: The wrong controller responded to a poll on a DLC or BSC line; EOT is transmitted; see Management Manual Appendix B. | 93109 | Wrong controller responded to poll on DLC/BSC (from <Node X.25 Address>) | warning |
| 0C_26: A controller is no longer being polled by the host; all stations on that controller are disconnected; info indicates: address of controller, see Management Manual Appendix B. | 93110 | Controller no longer polled by host on DLC/BSC (from <Node X.25 Address>, info=<Info>) | normal |
| 0C_27: A control message was received during transmission on a BSC3270 line; see Management Manual Appendix B. | 93111 | Control message received during transmission on BSC (from <Node X.25 Address>) | normal |
| 0C_29: The inactivity timeout expired on a DLC or BSC line; the VC is Cleared; info indicates further detail, see Management Manual Appendix B. | 93113 | Inactivity timeout expired on DLC/BSC (from <Node X.25 Address>, info=<Info>) | normal |
| 0C_30: The ENQ-SEL counter overflowed on a DLC or BSC line; station is disconnected. | 93120 | ENQ-SEL counter overflow on DLC/BSC (from <Node X.25 Address>) | warning |
| 0C_31: The TTD-SEL counter overflowed on a DLC or BSC line; the station is disconnected. | 93121 | TTD-SEL counter overflow on DLC/BSC (from <Node X.25 Address>) | warning |
| 0C_32: The ENQ.Rx counter overflowed on a DLC or BSC line. | 93122 | ENQ.Rx counter overflow on DLC/BSC (from <Node X.25 Address>) | warning |
| 0C_33: The NAK.Rx counter overflowed on a DLC or BSC line; info indicates further detail, see Management Manual Appendix B. | 93123 | NAK.Rx counter overflow on DLC/BSC (from <Node X.25 Address>, info=<Info>) | warning |
| 0C_34: The EOT.Tx counter overflowed on a DLC or BSC line; the station is disconnected. | 93124 | EOT.Tx counter overflow on DLC/BSC (from <Node X.25 Address>) | warning |
| 0C_35: The ENQ.Tx counter overflowed on a DLC or BSC line; info indicates further detail, see Management Manual Appendix B. | 93125 | ENQ.Tx counter overflow on DLC/BSC (from <Node X.25 Address>, info=<Info>) | warning |
| 0C_36: The NAK.Tx counter overflowed on a DLC or BSC line; info indicates further detail, see Management Manual Appendix B. | 93126 | NAK.Tx counter overflow on DLC/BSC (from <Node X.25 Address>, info=<Info>) | warning |
| 0C_43: An ENQ collision occurred on a DLC or BSC line; no transport will occur in data transfer mode; see Management Manual Appendix B. | 93139 | ENQ collision on DLC/BSC (from <Node X.25 Address>) | warning |
| 0C_44: An IT (ENQ) collision occurred on a DLC or BSC line; no transport will occur in data transfer mode; see Management Manual Appendix B. | 93140 | IT (ENQ) collision on DLC/BSC (from <Node X.25 Address>) | warning |
| 0C_45: An RVI was received on a DLC or BSC line; a "state RVI" message is sent; see Management Manual Appendix B. | 93141 | RVI message received on DLC/BSC (from <Node X.25 Address>) | normal |
| 0C_46: An ENQ message was received on a DLC or BSC line; transport in data transfer mode is either refused or authorized to continue; see Management Manual Appendix B. | 93142 | ENQ message received on DLC/BSC (from <Node X.25 Address>) | normal |
| 0C_47: An ENQ message was accepted on a DLC or BSC line; transport in data transfer mode is authorized; info indicates further detail, see Management Manual Appendix B. | 93143 | ENQ message accepted on DLC/BSC (from <Node X.25 Address>, info=<Info>) | normal |
| 0C_48: An ENQ message was refused on a DLC or BSC line; transport in data transfer mode is refused; info indicates further detail, see Management Manual Appendix B. | 93144 | ENQ message refused on DLC/BSC (from <Node X.25 Address>, info=<Info>) | warning |
| 0C_49: End of data transfer was detected on a DLC or BSC line; an EOT is sent; info indicates further detail, see Management Manual Appendix B. | 93145 | End of data transfer occurred on DLC/BSC (from <Node X.25 Address>, info=<Info>) | normal |
| 0C_50: An ENQ packet was received or transmitted on a DLC or BSC line; 3270=received, 2780=received, 3780=transmitted; info indicates further detail, see Management Manual Appendix B. | 93152 | ENQ on DLC/BSC (from <Node X.25 Address>, info=<Info>) | normal |
| 0C_51: A POLL or a WACK was received or transmitted on a DLC or BSC line; 3270=POLL received, 2780=WACK received, 3780=WACK transmitted; info indicates further detail. see Management Manual Appendix B. | 93153 | POLL or WACK on DLC/BSC (from <Node X.25 Address>, info=<Info>) | normal |
| 0C_52: A SELECT packet was received on a DLC or BSC line; info indicates further detail, see Management Manual Appendix B. | 93154 | SELECT received on DLC/BSC (from <Node X.25 Address>, info=<Info>) | normal |
| 0C_53: An ACK0 or a DLE0 was received or transmitted on a DLC or BSC line; 3270=ACK0 received, 2780=DLE0 received, 3780=DLE0 transmitted; info indicates further detail, see Management Manual Appendix B. | 93155 | ACK0 or DLE0 on DLC/BSC (from <Node X.25 Address>, info=<Info>) | normal |
| 0C_54: An ACK1 or a DLE1 was received or transmitted on a DLC or BSC line; 3270=ACK1 received, 2780=DLE1 transmitted, 3780=DLE1 received; info indicates further detail, see Management Manual Appendix B. | 93156 | ACK1 or DLE1 on DLC/BSC (from <Node X.25 Address>, info=<Info>) | normal |
| 0C_55: A NAK was received or transmitted on a DLC or BSC line; 3270=NAK received, 2780=NAK transmitted, 3780=NAK received; info indicates further detail, see Management Manual Appendix B. | 93157 | NAK on DLC/BSC (from <Node X.25 Address>, info=<Info>) | normal |
| 0C_56: An EOT was received or transmitted on a DLC or BSC line; 3270=EOT received, 2780=EOT transmitted, 3780=EOT received; info indicates further detail, see Management Manual Appendix B. | 93158 | EOT on DLC/BSC (from <Node X.25 Address>, info=<Info>) | normal |
| 0C_57: An RVI was received or transmitted on a DLC or BSC line; 3270=RVI received, 2780=RVI transmitted, 3780=RVI received; info indicates further detail, see Management Manual Appendix B. | 93159 | RVI on DLC/BSC (from <Node X.25 Address>, info=<Info>) | normal |
| 0C_58: A TTD was received or transmitted on a DLC or BSC line; 3270=TTD received, 2780=TTD transmitted, 3780=TTD received; info indicates further detail, see Management Manual Appendix B. | 93160 | TTD on DLC/BSC (from <Node X.25 Address>, info=<Info>) | normal |
| 0C_59: A WACK or DLE-EOT was received or transmitted on a DLC or BSC line; 3270=WACK received, 2780=DLE-EOT transmitted, 3780=DLE-EOT received; info indicates further detail, see Management Manual Appendix B. | 93161 | WACK or DLE-EOT on DLC/BSC (from <Node X.25 Address>, info=<Info>) | normal |
| 0C_5A: A specific poll packet was received on a DLC or BSC line; for 3270 only; info indicates further detail, see Management Manual Appendix B. | 93162 | Specific poll packet received on DLC/BSC (from <Node X.25 Address>, info=<Info>) | normal |
| 0C_60: A single block of data was received without error on a DLC or BSC line; info indicates further detail, see Management Manual Appendix B. | 93168 | Single-block data received on DLC/BSC (from <Node X.25 Address>, info=<Info>) | normal |
| 0C_61: A first block of data was received without error on a DLC or BSC line; info indicates further detail, see Management Manual Appendix B. | 93169 | First-block data received on DLC/BSC (from <Node X.25 Address>, info=<Info>) | normal |
| 0C_62: An intermediate block of data was received without error on a DLC or BSC line; info indicates further detail, see Management Manual Appendix B. | 93170 | Intermediate-block data received on DLC/BSC (from <Node X.25 Address>, info=<Info>) | normal |
| 0C_63: A last block of data was received without error on a DLC or BSC line; info indicates further detail, see Management Manual Appendix B. | 93171 | Last-block data received on DLC/BSC (from <Node X.25 Address>, info=<Info>) | normal |
| 0C_70: A message that was too long was received on a DLC or BSC line; info indicates further detail, see Management Manual Appendix B. | 93184 | Message too long on DLC/BSC (from <Node X.25 Address>, info=<Info>) | warning |
| 0C_71: A timeout occurred to a 2780/3780 device on a DLC or BSC line; info indicates further detail, see Management Manual Appendix B. | 93185 | Timeout occurred to 2780/3780 on DLC/BSC (from <Node X.25 Address>, info=<Info>) | warning |
| 0C_77: No STX character was present in a received block on a DLC or BSC line; no response is generated; info indicates further detail, see Management Manual Appendix B. | 93191 | No STX character present on DLC/BSC (from <Node X.25 Address>, info=<Info>) | warning |
| 0C_78: An ENQ was present in a data message; a NAK is transmitted; info indicates further detail, see Management Manual Appendix B. | 93192 | ENQ in data message on DLC/BSC (from <Node X.25 Address>, info=<Info>) | normal |
| 0C_79: A timeout occurred during reception of a block from a 3270 device on a DLC or BSC line; a NAK is transmitted in data transfer mode; info indicates further detail, see Management Manual Appendix B. | 93193 | Timeout during receive from 3270 on DLC/BSC (from <Node X.25 Address>, info=<Info>) | warning |
| 0C_80: A parity error was detected in a single block received on a DLC or BSC line; info indicates further detail, see Management Manual Appendix B. | 93200 | Parity error in single-block on DLC/BSC (from <Node X.25 Address>, info=<Info>) | minor |
| 0C_81: A parity error was detected in a first block received on a DLC or BSC line; info indicates further detail, see Management Manual Appendix B. | 93201 | Parity error in first-block on DLC/BSC (from <Node X.25 Address>, info=<Info>) | minor |
| 0C_82: A parity error was detected in an intermediate block received on a DLC or BSC line; info indicates further detail, see Management Manual Appendix B. | 93202 | Parity error in intermediate-block on DLC/BSC (from <Node X.25 Address>, info=<Info>) | minor |
| 0C_83: A parity error was detected in a last block received on a DLC or BSC line; info indicates further detail, see Management Manual Appendix B. | 93203 | Parity error in last-block on DLC/BSC (from <Node X.25 Address>, info=<Info>) | minor |
| 0C_90: A BCC error was detected in a single block received on a DLC or BSC line; info indicates further detail, see Management Manual Appendix B. | 93216 | BCC error in single-block on DLC/BSC (from <Node X.25 Address>, info=<Info>) | minor |
| 0C_91: A BCC error was detected in a first block received on a DLC or BSC line; info indicates further detail, see Management Manual Appendix B. | 93217 | BCC error in first-block on DLC/BSC (from <Node X.25 Address>, info=<Info>) | minor |
| 0C_92: A BCC error was detected in an intermediate block received on a DLC or BSC line; info indicates further detail, see Management Manual Appendix B. | 93218 | BCC error in intermediate-block on DLC/BSC (from <Node X.25 Address>, info=<Info>) | minor |
| 0C_93: A BCC error was detected in a last block received on a DLC or BSC line; info indicates further detail, see Management Manual Appendix B. | 93219 | BCC error in last-block on DLC/BSC (from <Node X.25 Address>, info=<Info>) | minor |
| 0C_97: A Reset occurred from the network on a DLC or BSC line; info indicates further detail, see Management Manual Appendix B. | 93223 | Reset occurred from network on DLC/BSC (from <Node X.25 Address>, info=<Info>) | normal |
| 0C_98: A Protocol violation occurred on a DLC or BSC line; the VC is Cleared; info indicates further detail, see Management Manual Appendix B. | 93224 | Protocol violation on DLC/BSC (from <Node X.25 Address>, info=<Info>) | warning |
| 0C_99: A reserved event for 2780/3780 devices occurred on a DLC or BSC line; info indicates further detail, see Management Manual Appendix B. | 93225 | Reserved event for 2780/3780 occurred on DLC/BSC (from <Node X.25 Address>, info=<Info>) | warning |
| 0D_01: A multi-frame packet was received in the window guard region on an MLP line; a Restart is sent. | 93329 | Multi-frame in window guard region on MLP (from <Node X.25 Address>, line <Port Number>) | warning |
| 0D_02: A multi-frame packet was received outside the window on an MLP line; the frame is ignored. | 93330 | Multi-frame outside the window on MLP (from <Node X.25 Address>, line <Port Number>) | warning |
| 0D_03: An MT4 timeout occurred on an MLP line; the MLP bundle is taken down. | 93331 | Timeout of MT4 occurred on MLP (from <Node X.25 Address>, line <Port Number>) | warning |
| 0D_04: An MT1 timeout (lost-frame) occurred on an MLP line; a Restart is sent. | 93332 | Timeout of MT1 occurred on MLP (from <Node X.25 Address>, line <Port Number>) | warning |
| 0D_05: The MT4 timer was initiated on an MLP line. | 93333 | Timer MT4 initiated on MLP (from <Node X.25 Address>, line <Port Number>) | normal |
| 0D_06: An invalid multi-frame with R=1 was received during Reset on an MLP line; Level2 and MLP are Reset. | 93334 | Invalid multi-frame (R=1) received on MLP (from <Node X.25 Address>, line <Port Number>) | warning |
| 0D_07: A multi-frame with R=1 was received during reset on an MLP line; the frame is ignored. | 93335 | Multi-frame (R=1) ignored on MLP (from <Node X.25 Address>, line <Port Number>) | minor |
| 0D_08: An invalid multi-frame with C=1 was received during reset on an MLP line; Level2 and MLP are Reset. | 93336 | Invalid multi-frame (C=1) received on MLP (from <Node X.25 Address>, line <Port Number>) | warning |
| 0D_09: A multi-frame with C=1 was received during reset on an MLP line; the frame is ignored. | 93337 | Multi-frame (C=1) ignored on MLP (from <Node X.25 Address>, line <Port Number>) | minor |
| 0D_0A: A multi-frame of length 2 was received on an MLP line; the frame is ignored. | 93338 | Multi-frame length=2 on MLP (from <Node X.25 Address>, line <Port Number>) | minor |
| 0D_0B: A Multi-frame with (R=1) and (C=1) both TRUE were received on an MLP line; the frame is ignored. | 93339 | Multi-frame (R=1, C=1) received on MLP (from <Node X.25 Address>, line <Port Number>) | minor |
| 0D_0C: A Reset was received on a multi-frame during data transfer on an MLP line; Level2 and MLP are Reset; if config parameter set=reset Level3. | 93340 | Reset Multi-frame during data transfer on MLP (from <Node X.25 Address>, line <Port Number>) | warning |
| 0D_0D: An MT3 timeout occurred on an MLP line. | 93341 | Timeout of MT3 occurred on MLP (from <Node X.25 Address>, line <Port Number>) | warning |
| 0D_0E: A bundle came online on an MLP line. | 93342 | Bundle online on MLP (from <Node X.25 Address>, line <Port Number>) | normal |
| 0D_0F: A bundle changed state on an MLP line; info indicates: line number within bundle, new state, line level state, lines in service on bundle. | 93343 | Bundle changed state on MLP (from <Node X.25 Address>, line <Port Number>, info=<Info>) | warning |
| 0E_02: Line signal changed: Modem circuit 117 (StandBy) off, terminal circuit 114 (TxClk) off. | 93586 | Line signal 117/114 change on PSTN (from <Node X.25 Address>, line <Port Number>) | normal |
| 0E_03: Line signal changed: Modem circuit 117 (StandBy) on, terminal circuit 114 (TxClk) off. | 93587 | Line signal 117/114 change on PSTN (from <Node X.25 Address>, line <Port Number>) | normal |
| 0E_04: A Clear occurred due to VC being absent on a DLC or BSC line; the data path is Cleared. | 93588 | Clear if VC absent on PSTN (from <Node X.25 Address>, line <Port Number>) | normal |
| 0E_05: A failure of type B1 occurred on a PSTN line, B1: modem unable to handle Call due to blacklisted numbers; the Call is Cleared; info indicates: diagnostic cause: 00 = not significant 02 = delayed number 04 = blacklisted number 05 = absence of tone 06 = remote subscriber busy 07 = remote subscriber absent 08 = remote subscriber is not a modem, number of digits in telephone number, telephone number. | 93589 | Failure type B1 on PSTN (from <Node X.25 Address>, line <Port Number>, info=<Info>) | warning |
| 0E_06: A failure of type A or C occurred on a PSTN line, A: local modem dialog problem, C: switched network unable to route Call; a subsequent Call attempt is made; info indicates: diagnostic cause: 00 = not significant 02 = delayed number 04 = blacklisted number 05 = absence of tone 06 = remote subscriber busy 07 = remote subscriber absent 08 = remote subscriber is not a modem. | 93590 | Failure type A/C on PSTN (from <Node X.25 Address>, line <Port Number>, info=<Info>) | warning |
| 0E_07: A failure of type B2 or D occurred on a PSTN line. B2: modem unable to handle Call due to delayed numbers from previous Call failure, D: remote subscriber cannot be connected; a subsequent Call attempt is made; info indicates: diagnostic cause: 00 = not significant 02 = delayed number 04 = blacklisted number 05 = absence of tone 06 = remote subscriber busy 07 = remote subscriber absent 08 = remote subscriber is not a modem, number of digits in telephone number, telephone number. | 93591 | Failure type B2/D on PSTN (from <Node X.25 Address>, line <Port Number>, info=<Info>) | warning |
| 0E_08: A failure of type E occurred on a PSTN line, E: remote subscriber connected but frame or packet level not setup (Call collision); the data path is Cleared; info indicates: diagnostic cause: 00 = not significant 02 = delayed number 04 = blacklisted number 05 = absence of tone 06 = remote subscriber busy 07 = remote subscriber absent 08 = remote subscriber is not a modem. | 93592 | Failure type E on PSTN (from <Node X.25 Address>, line <Port Number>, info=<Info>) | minor |
| 0E_0A: A Backup or Overflow link was established on a PSTN line; enters the Call state; info indicates: FF marker, E.164 address length, E.164 address, AA marker, X.121 address length, X.121 address, AA marker, MLP bundle number (FF=not significant). | 93594 | Backup link established on PSTN (from <Node X.25 Address>, line <Port Number>, info=<Info>) | normal |
| 0E_0B: An attempt to establish a Backup or Overflow link on a PSTN line failed; enters the Idle state; info indicates: FF marker, E.164 address length, E.164 address, AA marker, X.121 address length, X.121 address, AA marker, MLP bundle number (FF=not significant), failure cause. | 93595 | Backup link failed on PSTN (from <Node X.25 Address>, line <Port Number>, info=<Info>) | warning |
| 0E_0C: Notification of a Switched line disconnection occurred on a PSTN line; info indicates: FF marker, E.164 address length, E.164 address, AA marker, X.121 address length, X.121 address. | 93596 | Switched line disconnection on PSTN (from <Node X.25 Address>, line <Port Number>, info=<Info>) | normal |
| 0F_41: An outgoing connection is in progress on a VC/ESV line; a Transport Request is sent; info indicates: Logical Channel number. | 93905 | Outgoing connection in progress on VC/ESV (from <Node X.25 Address>, line <Port Number>, info=<Info>) | normal |
| 0F_42: An incoming connection is in progress on a VC/ESV line; a Response is sent to a Transport Request; info indicates: Logical Channel number. | 93906 | Incoming connection in progress on VC/ESV (from <Node X.25 Address>, line <Port Number>, info=<Info>) | normal |
| 0F_43: The data transfer state was entered on a VC/ESV line; node is ready to transfer data; info indicates: Logical Channel number. | 93907 | Enter data transfer on VC/ESV (from <Node X.25 Address>, line <Port Number>, info=<Info>) | normal |
| 0F_44: An outgoing clear signal was received on a VC/ESV line; a data transfer Transport Request is asserted and node awaits incoming Clear signal Confirmation; info indicates: Logical Channel number. | 93908 | Outgoing Clear signal received on VC/ESV (from <Node X.25 Address>, line <Port Number>, info=<Info>) | normal |
| 0F_45: An incoming Clear signal was received on a VC/ESV line; data transfer is Cleared to subscriber and node awaits outgoing Clear signal Confirmation; info indicates: Logical Channel number. | 93909 | Incoming Clear signal received on VC/ESV (from <Node X.25 Address>, line <Port Number>, info=<Info>) | normal |
| 10_00: Data Resynchronization occurred on a VC/N4 line. | 94096 | Data Resynchronization on VC/N4 (from <Node X.25 Address>) | normal |
| 10_01: Resynchronization of terminated data occurred on a VC/N4 line. | 94097 | Terminated data Resynchronization on VC/N4 (from <Node X.25 Address>) | normal |
| 10_02: Retransmission of terminated data occurred on a VC/N4 line. | 94098 | Retransmission of terminated data on VC/N4 (from <Node X.25 Address>) | normal |
| 10_10: The maximum number of data retransmissions was exhausted on a VC/N4 line; the line is disconnected. | 94112 | Maximum retransmissions exhausted on VC/N4 (from <Node X.25 Address>) | warning |
| 10_20: A TPDU DT with an unexpected number was received on a VC/N4 line; the line is disconnected. | 94128 | TPDU DT with unexpected number on VC/N4 (from <Node X.25 Address>) | warning |
| 10_21: A TPDU ED with an unexpected number was received on a VC/N4 line; the line is disconnected. | 94129 | TPDU ED with unexpected number on VC/N4 (from <Node X.25 Address>) | warning |
| 10_22: A TPDU EA was received not corresponding with a TPDU ED on a VC/N4 line; the line is disconnected. | 94130 | TPDU EA not corresponding with an ED on VC/N4 (from <Node X.25 Address>) | warning |
| 10_23: A TPDU RJ or TPDU AK was received with an expected number or the next TPDU DT outside the valid window on a VC/N4 line; the line is disconnected. | 94131 | TPDU DT expected number outside window on VC/N4 (from <Node X.25 Address>) | warning |
| 10_25: A reference number in a received frame is unknown on a VC/N4 line; the line is disconnected. | 94133 | Reference number unknown on VC/N4 (from <Node X.25 Address>) | warning |
| 10_26: A TPDU format error occurred on a VC/N4 line; the line is disconnected. | 94134 | TPDU format error on VC/N4 (from <Node X.25 Address>) | warning |
| 10_27: An unknown TPDU was received on a VC/N4 linel the line is disconnected. | 94135 | Unknown TPDU on VC/N4 (from <Node X.25 Address>) | warning |
| 10_51: A transport connection was established (calling side) on a VC/N4 line; a transport connection Confirmation is sent and node is ready for data transfer. | 94177 | Transport connection established (calling side) on VC/N4 (from <Node X.25 Address>, line <Port Number>) | normal |
| 10_52: A transport connection was established (called side) on a VC/N4 line; the node is ready for data transfer. | 94178 | Transport connection established (called side) on VC/N4 (from <Node X.25 Address>, line <Port Number>) | normal |
| 10_53: A TPDU DR was received on a VC/N4 line; a TPDU DC is sent. | 94179 | TPDU DR received on VC/N4 (from <Node X.25 Address>, line <Port Number>) | normal |
| 10_54: A TPDU DC was received on a VC/N4 line; a "Connection Disconnect" is sent. | 94180 | TPDU DC received on VC/N4 (from <Node X.25 Address>, line <Port Number>) | normal |
| 10_55: A protocol error occurred on a VC/N4 line; a "Transport Disconnect Indication" is sent. | 94181 | Protocol error on VC/N4 (from <Node X.25 Address>, line <Port Number>) | warning |
| 10_56: Resynchronization 56 occurred on a VC/N4 line; the TPDU CR is re-transmitted. | 94182 | Resynchronization 56 on VC/N4 (from <Node X.25 Address>, line <Port Number>) | normal |
| 10_57: Resynchronization 57 occurred on a VC/N4 line; flag is positioned for data resynchronization. | 94183 | Resynchronization 57 on VC/N4 (from <Node X.25 Address>, line <Port Number>) | normal |
| 10_58: Resynchronization 58 occurred on a VC/N4 line; the TPDU CR is re-transmitted. | 94184 | Resynchronization 58 on VC/N4 (from <Node X.25 Address>, line <Port Number>) | normal |
| 10_59: Resynchronization 59 occurred on a VC/N4 line; the TPDU CR is re-transmitted. | 94185 | Resynchronization 59 on VC/N4 (from <Node X.25 Address>, line <Port Number>) | normal |
| 10_5A: A network connection was disconnected on a VC/N4 line; a "Transport Disconnect Indication" is sent. | 94186 | Network connection disconnected on VC/N4 (from <Node X.25 Address>, line <Port Number>) | normal |
| 10_60: No more Logical Channel resources are available on a VC/N4 line; the line is disconnected. | 94192 | No more LC resources on VC/N4 (from <Node X.25 Address>) | minor |
| 10_61: No more reference numbers are available on a VC/N4 line; the line is disconnected. | 94193 | No more reference numbers on VC/N4 (from <Node X.25 Address>) | minor |
| 11_00: The network connected without error on a VC/IR line. | 94352 | Network connected on VC/IR (from <Node X.25 Address>) | normal |
| 11_01: Re-establishment succeeded on a VC/IR line. | 94353 | Re-establishment succeeded on VC/IR (from <Node X.25 Address>) | normal |
| 11_02: The network disconnected without error on a VC/IR line. | 94354 | Network disconnected on VC/IR (from <Node X.25 Address>) | normal |
| 11_05: A Clear signal was received from the network on a VC/IR line; the line is re-established. | 94357 | Clear signal from network on VC/IR (from <Node X.25 Address>) | warning |
| 11_06: A Reset was received from the network on a VC/IR line. | 94358 | Reset from network on VC/IR (from <Node X.25 Address>) | normal |
| 11_07: A Clear was received while in the opened state on a VC/IR line; the line is disconnected. | 94359 | Clear in opened state on VC/IR (from <Node X.25 Address>) | normal |
| 11_10: The maximum number of Call retries was reached on a VC/IR line; the line is disconnected. | 94368 | Maximum Call retries exceeded on VC/IR (from <Node X.25 Address>) | warning |
| 11_11: The Wait-to-Reconnect timer expired on a VC/IR line; the line is disconnected. | 94369 | Wait-to-Reconnect timeout on VC/IR (from <Node X.25 Address>) | warning |
| 11_15: A Clear signal was received in error on a VC/IR line; IR protocol error; the line is disconnected. | 94373 | Clear signal in error on VC/IR (from <Node X.25 Address>) | warning |
| 11_20: There was no TPDU PI in an incoming Call on a VC/IR line; the line is disconnected. | 94384 | No TPDU PI in incoming Call on VC/IR (from <Node X.25 Address>) | warning |
| 11_21: The NSAP (calling) is absent or in error on a VC/IR line; the line is disconnected. | 94385 | NSAP error on VC/IR (from <Node X.25 Address>) | warning |
| 11_22: An attempt to restore an unknown connection was made on a VC/IR line; the line is disconnected. | 94386 | Attempt to restore unknown connection on VC/IR (from <Node X.25 Address>) | warning |
| 11_23: The Call data was not compatible oe was insufficient on a VC/IR line; the line is disconnected. | 94387 | Call data error on VC/IR (from <Node X.25 Address>) | warning |
| 11_24: There was no Call data present in a Call on a VC/IR line; the line is disconnected. | 94388 | No Call data on VC/IR (from <Node X.25 Address>) | warning |
| 11_25: A Call data Confirmation was received with inconsistent information on a VC/IR line; the line is disconnected. | 94389 | Inconsistent Call data Confirmation on VC/IR (from <Node X.25 Address>) | warning |
| 11_26: Data was received while waiting for Call data Confirmation on a VC/IR line; the line is disconnected. | 94390 | Data received while awaiting Call Confirmation on VC/IR (from <Node X.25 Address>) | warning |
| 11_30: A repeated Call without error was received during disconnect on a VC/IR line; the line is disconnected. | 94400 | Repeated Call during disconnect on VC/IR (from <Node X.25 Address>) | warning |
| 11_31: A Clear signal was received while in the Invitation-to-Clear state on a VC/IR line; the line is re-established then disconnected. | 94401 | Clear signal during Invitation-to-Clear on VC/IR (from <Node X.25 Address>) | warning |
| 11_32: The remote side was cleared from the network connection on a VC/IR line. | 94402 | Remote side cleared from network on VC/IR (from <Node X.25 Address>) | warning |
| 11_33: An Invitation-to-Clear was received while in the Opened state on a VC/IR line; the line is disconnected. | 94403 | Invitation-to-Clear in Opened state on VC/IR (from <Node X.25 Address>) | warning |
| 11_50: There are no more Logical Channels available on a VC/IR line; the line is disconnected. | 94432 | No more Logical Channels available on VC/IR (from <Node X.25 Address>) | warning |
| 11_51: The network connection reference was lost on a VC/IR line; the line is disconnected. | 94433 | Network connection reference lost on VC/IR (from <Node X.25 Address>) | warning |
| 12_00: The physical Line Level is down on an ISDN line; all calls are interrupted, all line levels are down. | 94608 | Line Level down on ISDN-Line (from <Node X.25 Address>, line <Port Number>) | major |
| 12_01: The physical Line Level is up on an ISDN line; the S-interface is activated, the TEI is allocated. | 94609 | Line Level up on ISDN-Line (from <Node X.25 Address>, line <Port Number>) | normal |
| 12_02: A Physical Management activation indication was received on an ISDN line; S0 interface is activated, data transfer is now possible. | 94610 | Physical Management activation on ISDN-Line (from <Node X.25 Address>, line <Port Number>) | normal |
| 12_03: A Physical Management inactivation indication was received on an ISDN line; S0 interface is inactivated, data transfer is no longer possible. | 94611 | Physical Management inactivation on ISDN-Line (from <Node X.25 Address>, line <Port Number>) | minor |
| 12_04: A Physical Management level error signal indication occurred on an ISDN line; cause is loss of frame locking or loss of synchronization. | 94612 | Physical Management error signal on ISDN-Line (from <Node X.25 Address>, line <Port Number>) | minor |
| 12_05: A Physical Management level error recovery indication occurred on an ISDN line; enters the Active state. | 94613 | Physical Management error recovery on ISDN-Line (from <Node X.25 Address>, line <Port Number>) | normal |
| 12_06: A CRC error occurred on an ISDN line; the frame is ignored. | 94614 | CRC error on ISDN-Line (from <Node X.25 Address>, line <Port Number>) | minor |
| 12_07: An ABORT sequence was received on an ISDN line; the frame is ignored. | 94615 | ABORT sequence received on ISDN-Line (from <Node X.25 Address>, line <Port Number>) | minor |
| 12_08: A Reset error occurred on an ISDN line; the frame is ignored. | 94616 | Reset error on ISDN-Line (from <Node X.25 Address>, line <Port Number>) | minor |
| 12_09: An Overrun/Underrun error occurred on an ISDN line; the frame is ignored. | 94617 | Overrun/Underrun on ISDN-Line (from <Node X.25 Address>, line <Port Number>) | minor |
| 12_0A: The current frame was received correctly on an ISDN line but the previous frame was lost; the frame is ignored. | 94618 | Previous frame lost on ISDN-Line (from <Node X.25 Address>, line <Port Number>) | warning |
| 12_0B: A CRC error occurred on the current frame on an ISDN line and the previous frame was lost; the frame is ignored. | 94619 | CRC error and previous frame lost on ISDN-Line (from <Node X.25 Address>, line <Port Number>) | minor |
| 12_0C: An ABORT sequence occurred on the current frame on an ISDN line and the previous frame was lost; the frame is ignored. | 94620 | ABORT sequence and previous frame lost on ISDN-Line (from <Node X.25 Address>, line <Port Number>) | minor |
| 12_0D: A Reset error occurred on the current frame on an ISDN line and the previous frame was lost; the frame is ignored. | 94621 | Reset error and previous frame lost on ISDN-Line (from <Node X.25 Address>, line <Port Number>) | minor |
| 12_0E: An Overrun occurred on the current frame on an ISDN line and the previous frame was lost; the frame is ignored. | 94622 | Overrun and previous frame lost on ISDN-Line (from <Node X.25 Address>, line <Port Number>) | minor |
| 12_30: A Supervisory frame with F=1 was received on an ISDN line which is in state 7; the frame is processed. | 94656 | Received S-frame (F=1) in state 7 on ISDN-Frame (from <Node X.25 Address>, line <Port Number>) | normal |
| 12_31: A DM frame with F=1 was received on an ISDN line which is in state 7 or 8; the frame is ignored. | 94657 | Received DM (F=1) in state 7/8 on ISDN-Frame (from <Node X.25 Address>, line <Port Number>) | minor |
| 12_32: A UA frame with F=1 was received on an ISDN line which is in state 4,7 or 8; the TEI is deleted. | 94658 | Received UA (F=1) in state 4/7/8 on ISDN-Frame (from <Node X.25 Address>, line <Port Number>) | normal |
| 12_33: A UA frame with F=0 was received on an ISDN line which is in state 4,5,6,7 or 8; the TEI is deleted. | 94659 | Received UA (F=0) in state 4/5/6/7/8 on ISDN-Frame (from <Node X.25 Address>, line <Port Number>) | normal |
| 12_34: A DM frame with F=0 was received on an ISDN line which is in state 7 or 8; Level 2 is re-initialized. | 94660 | Received DM (F=0) in state 7/8 on ISDN-Frame (from <Node X.25 Address>, line <Port Number>) | warning |
| 12_35: A SABME frame was received on an ISDN line which is in state 7 or 8; a UA is sent and state becomes 7. | 94661 | Received SABME in state 7/8 on ISDN-Frame (from <Node X.25 Address>, line <Port Number>) | normal |
| 12_36: SABME Retries exceeded parameter N200 on an ISDN line which is in state 5; state becomes 4. | 94662 | SABME retries in state 5 on ISDN-Frame (from <Node X.25 Address>, line <Port Number>) | warning |
| 12_37: DISC retries exceeded parameter N200 on an ISDN line which is in state 6; state becomes 4. | 94663 | DISC retries in state 6 on ISDN-Frame (from <Node X.25 Address>, line <Port Number>) | warning |
| 12_38: Poll status was received on an ISDN line which is in state 8; level 2 is re-initialized. | 94664 | Poll status in state 8 on ISDN-Frame (from <Node X.25 Address>, line <Port Number>) | warning |
| 12_39: An N(R) error occurred on an ISDN line which is in state 7 or 8; level 2 is re-initialized. | 94665 | N(R) error in state 7/8 on ISDN-Frame (from <Node X.25 Address>, line <Port Number>) | warning |
| 12_3A: An FRMR frame was received on an ISDN line which is in state 7 or 8; level 2 is re-initialized. | 94666 | FRMR received in state 7/8 on ISDN-Frame (from <Node X.25 Address>, line <Port Number>) | warning |
| 12_3B: An unused frame was received on an ISDN line which is in state 4,5,7 or 8; level 2 is re-initialized if the state is not 4. | 94667 | Unused frame received on ISDN-Frame (from <Node X.25 Address>, line <Port Number>) | warning |
| 12_3C: An unauthorized I-field was received on an ISDN line which is in one of states 4-8; the frame is ignored. | 94668 | Unauthorized I-field in state 4-8 on ISDN-Frame (from <Node X.25 Address>, line <Port Number>) | minor |
| 12_3D: A frame of the wrong size was received on an ISDN line which is in one of state 4-8; level 2 is re-initialized if not in state 4. | 94669 | Frame wrong size in state 4-8 on ISDN-Frame (from <Node X.25 Address>, line <Port Number>) | warning |
| 12_3E: An N201 error occurred on an ISDN line which is in one of states 4-8; level 2 is re-initialized if not in state 4. | 94670 | N201 error in state 4-8 on ISDN-Frame (from <Node X.25 Address>, line <Port Number>) | warning |
| 12_3F: A frame with a 1-byte address field was received on an ISDN line which is in one of states 4-8; the frame is ignored. | 94671 | Frame with 1-byte address in state 4-8 on ISDN-Frame (from <Node X.25 Address>, line <Port Number>) | minor |
| 12_40: A frame which is too short was received on an ISDN line which is in one of states 4-8; the frame is ignored. | 94672 | Frame too short in state 4-8 on ISDN-Frame (from <Node X.25 Address>, line <Port Number>) | minor |
| 12_41: A frame with an incorrect SAPI was received on an ISDN line which is in one of states 4-8; the frame is ignored. | 94673 | Frame with incorrect SAPI in state 4-8 on ISDN-Frame (from <Node X.25 Address>, line <Port Number>) | minor |
| 12_42: A frame with an address field of more than 2 bytes was received on an ISDN line; the frame is ignored. | 94674 | Frame with more than 2-byte address field on ISDN-Frame (from <Node X.25 Address>, line <Port Number>) | minor |
| 12_43: A frame with an unknown SAPI/TEI combination was received on an ISDN line; the frame is ignored. | 94675 | Frame with unknown SAPI/TEI on ISDN-Frame (from <Node X.25 Address>, line <Port Number>) | minor |
| 12_44: An N(S) error occurred on an ISDN line which is in state 7 or 8; the frame is processed. | 94676 | N(S) error in states 7, 8 on ISDN-Frame (from <Node X.25 Address>, line <Port Number>) | warning |
| 12_45: A Control frame with C=0 was received on an ISDN line; the frame is ignored. | 94677 | Control frame with C=0 on ISDN-Frame (from <Node X.25 Address>, line <Port Number>) | minor |
| 12_46: A Fixed TEI deletion error occurred on an ISDN line; user must reset line; network suspects a duplicate assignment of TEI on the bus. | 94678 | Fixed TEI deletion on ISDN-Frame (from <Node X.25 Address>, line <Port Number>) | warning |
| 12_4E: Multiple frame mode is set on an ISDN line; level 2 enters state 7. | 94686 | Multiple frame mode set on ISDN-Frame (from <Node X.25 Address>, line <Port Number>) | normal |
| 12_4F: Multiple frame mode is reset on an ISDN line; level 2 enters state 4. | 94687 | Multiple frame mode reset on ISDN-Frame (from <Node X.25 Address>, line <Port Number>) | normal |
| 12_60: A Protocol level D event occured on an ISDN line; see the event list for ISDN Protocol D in the manual. | 94704 | Protocol level D event on ISDN-Frame (from <Node X.25 Address>) | normal |
| 12_90: The content of an obligatory Element Information (Ei) is invalid on an ISDN line; the Call is aborted. | 94752 | Content of Ei in error on ISDN-Call (from <Node X.25 Address>, line <Port Number>) | warning |
| 12_91: Primary access instead of basic access occurred on an ISDN line; the Call is aborted. | 94753 | Primary access instead of basic access on ISDN-Call (from <Node X.25 Address>, line <Port Number>) | warning |
| 12_92: Channel B is not available for a new incoming call on an ISDN line; the Call is aborted. | 94754 | Channel B unavailable for incoming call on ISDN-Call (from <Node X.25 Address>, line <Port Number>) | warning |
| 12_93: Element Information (Ei) of higher layers is not compatible on an ISDN line; the Call is aborted. | 94755 | Higher layer Ei not compatible on ISDN-Call (from <Node X.25 Address>, line <Port Number>) | warning |
| 12_94: The Calling E.164 address is not in the list in a Call Reject on an ISDN line; the Call is aborted. | 94756 | Calling E.164 address not in list on ISDN-Call (from <Node X.25 Address>, line <Port Number>) | warning |
| 12_95: A timeout expired or a problem was detected by lower layers on an ISDN line; the Call is aborted. | 94757 | Timeout expired on ISDN-Call (from <Node X.25 Address>, line <Port Number>) | warning |
| 12_96: A Call was refused due to S0 interface behavior on an ISDN line; the Call is aborted. | 94758 | Call refused due to S0 behavior on ISDN-Call (from <Node X.25 Address>, line <Port Number>) | warning |
| 12_97: A Call was refused due to S0 interface selection on an ISDN line; the Call is aborted. | 94759 | Call refused due to selected S0 on ISDN-Call (from <Node X.25 Address>, line <Port Number>) | warning |
| 12_98: Row Range in C10 is inconsistent on an ISDN line; the Call is aborted. | 94760 | Row Range in C10 inconsistent on ISDN-Call (from <Node X.25 Address>, line <Port Number>) | warning |
| 12_99: An MLP Call was rejected on an ISDN line; the Call is aborted. | 94761 | MLP Call rejected on ISDN-Call (from <Node X.25 Address>, line <Port Number>) | warning |
| 12_A0: A translation error from X.121 to E.164 addresses occurred on an ISDN line; the Call is aborted. | 94768 | Address translation error X.121 to E.164 on ISDN-Call (from <Node X.25 Address>, line <Port Number>) | warning |
| 12_A1: There is no channel available for an outgoing call on an ISDN line; the Call is aborted. | 94769 | Channel unavailable for outgoing call on ISDN-Call (from <Node X.25 Address>, line <Port Number>) | warning |
| 12_A2: There is insufficient context information available on a Call on an ISDN line; the Call is aborted. | 94770 | Insufficient context on Call on ISDN-Call (from <Node X.25 Address>, line <Port Number>) | warning |
| 12_A3: The maximum number of VCs were exceeded on an ISDN line; the VC is aborted on overflow to another channel. | 94771 | Maximum VCs exceeded on ISDN-Call (from <Node X.25 Address>, line <Port Number>) | warning |
| 12_A4: The position of profile C30 is inconsistent on an ISDN line; the Call is aborted. | 94772 | Profile C30 position inconsistent on ISDN-Call (from <Node X.25 Address>, line <Port Number>) | warning |
| 12_A5: The content of profile C30 is inconsistent on an ISDN line; the Call is aborted. | 94773 | Profile C30 content inconsistent on ISDN-Call (from <Node X.25 Address>, line <Port Number>) | warning |
| 12_A6: The B-channel is not configured on an ISDN line; the Call is aborted. | 94774 | B-channel not configured on ISDN-Call (from <Node X.25 Address>, line <Port Number>) | warning |
| 12_A7: Backup attempt retries were exceeded on an ISDN line; the Call is aborted. | 94775 | Backup retries exceeded on ISDN-Call (from <Node X.25 Address>, line <Port Number>) | warning |
| 12_A8: Backup attempt is terminated on an ISDN line; the Call is aborted. | 94776 | Backup attempts terminated on ISDN-Call (from <Node X.25 Address>, line <Port Number>) | warning |
| 12_B0: A B-channel disconnect indication occurred on an ISDN line; line is channel D or LLP number; info indicates: channel B line number, E.164 address of remote user. | 94784 | B-channel disconnect indication on ISDN-Call (from <Node X.25 Address>, line <Port Number>, info=<Info>) | warning |
| 12_B1: A B-channel connect indication occurred on an ISDN line; line is channel D or LLP number; info indicates: channel B line number, E.164 address length, E.164 address, AA marker, X.121 address length, X.121 address, AA marker, main line number of bundle (FF = not significant). | 94785 | B-channel connect indication on ISDN-Call (from <Node X.25 Address>, line <Port Number>, info=<Info>) | normal |
| 12_B2: A B-channel connect indication requested by remote party occurred on an ISDN line; line is channel D or LLP number; info indicates: channel B line number, E.164 address length, E.164 address, AA marker, X.121 address length, X.121 address, AA marker, main line number of bundle (FF = not significant). | 94786 | B-channel connect remote indication on ISDN-Call (from <Node X.25 Address>, line <Port Number>, info=<Info>) | normal |
| 12_B3: A connection request (local or remote) failed on an ISDN line; line is channel D or LLP number; info indicates: channel B line number, E.164 address length, E.164 address, AA marker, X.121 address length, X.121 address, AA marker, main line number of bundle (FF = not significant). | 94787 | Connect failure on ISDN-Call (from <Node X.25 Address>, line <Port Number>, info=<Info>) | warning |
| 12_B4: A disconnect request failed on an ISDN line; line is channel D or LLP number; info indicates: call reference number, channel B line number, E.164 address of remote user. | 94788 | Disconnect failure on ISDN-Call (from <Node X.25 Address>, line <Port Number>, info=<Info>) | warning |
| 13_01: A Rerouting request was transmitted transparently on X.29, parameter DR2 is present with length=0; the Call is transmitted transparently. | 94865 | Rerouting request transmitted transparently on X.29 (from <Node X.25 Address>, line <Port Number>) | normal |
| 13_02: A Rerouting request was refused due to a syntax error or a parameter not being processed on X.29; a negative routing report is transmitted. | 94866 | Rerouting request refused due to syntax error on X.29 (from <Node X.25 Address>, line <Port Number>) | warning |
| 13_03: A Clear was received on a transmitted Call due to a rerouting request on X.29; a negative routing report is transmitted. | 94867 | Clear received due to rerouting request on X.29 (from <Node X.25 Address>, line <Port Number>) | normal |
| 13_04: A Clear was received on a transmitted Call due to receipt of a new X.29 selection or a reconnect command. | 94868 | Clear received due to X.29 select (from <Node X.25 Address>, line <Port Number>) | normal |
| 14_01: A transmission failure occurred on a Bridge / Router line. | 95121 | Transmission failure on B/R (from <Node X.25 Address>, line <Port Number>) | warning |
| 14_02: A CAM full indication occurred on a Bridge / Router line. | 95122 | CAM full indication on B/R (from <Node X.25 Address>, line <Port Number>) | normal |
| 14_03: The Bridge node is now online. | 95123 | Bridge online (from <Node X.25 Address>, line <Port Number>) | normal |
| 14_04: The Bridge node is now offline. | 95124 | Bridge offline (from <Node X.25 Address>, line <Port Number>) | warning |
| 14_05: The SLL Bridge is now online; info indicates: 1byte = free, 2bytes = SLL number, 2bytes = DNIC of remote equipment, 1byte = ZO of remote equipment, 1byte = remote subscriber, 1byte = local subscriber, 1byte = number of SLL handler line, 1byte = encapsulation type. | 95125 | SLL Bridge online (from <Node X.25 Address>, line <Port Number>, info=<Info>) | normal |
| 14_06: The SLL Bridge is now offline; info indicates: 1byte = free, 2bytes = SLL number, 2bytes = DNIC of remote equipment, 1byte = ZO of remote equipment, 1byte = remote subscriber, 1byte = local subscriber, 1byte = number of SLL handler line, 1byte = encapsulation type. | 95126 | SLL Bridge offline (from <Node X.25 Address>, line <Port Number>, info=<Info>) | warning |
| 14_07: The Bridge / Router is now synchronized; info indicates: 2bytes = SLL number. | 95127 | Node synchronized on B/R (from <Node X.25 Address>, line <Port Number>, info=<Info>) | normal |
| 14_08: A duplicate IP address or Ethernet address was detected in an ARP packet; info indicates: 1byte = free, 4bytes = IP address of router, 4bytes = IP address of first station, 4bytes = IP address of second station, 6bytes = Ethernet address of first station, 6bytes = Ethernet address of second station. | 95128 | Duplicate IP or Ethernet address on B/R (from <Node X.25 Address>, line <Port Number>, info=<Info>) | warning |
| 14_09: The address resolution process run on an address in an ARP packet failed; info indicates: 1byte = free, 4bytes = IP address of router, 4bytes = IP address not resolved. | 95129 | Address resolution failed on B/R (from <Node X.25 Address>, line <Port Number>, info=<Info>) | warning |
| 14_0A: An IP Router error occurred; info indicates: 1byte = free, 4bytes = IP address of router, 1byte = error code. | 95130 | IP Router error (from <Node X.25 Address>, line <Port Number>, info=<Info>) | warning |
| 14_0B: The IP Router is now online; info indicates: 1byte = free, 4bytes = IP address of router. | 95131 | IP Router online (from <Node X.25 Address>, line <Port Number>, info=<Info>) | normal |
| 14_0C: The IP Router is now offline. | 95132 | IP Router offline (from <Node X.25 Address>, line <Port Number>) | warning |
| 14_0D: An unknown destination address was received by the IP Router; info indicates: 1byte = free, 4bytes = IP address of router, 4bytes = IP addres in fault, 4bytes = source IP address of datagram, 1byte = error code: 00 = ICMP net unreachable, 01 = ICMP host unreachable, 02 = ICMP protocol unreachable. | 95133 | IP Router bad destination address (from <Node X.25 Address>, line <Port Number>, info=<Info>) | warning |
| 14_0E: The IP Router encountered a timeout; info indicates: 1byte = free, 4bytes = IP address of router, 4bytes = destination IP address of datagram, 4bytes = source IP address of datagram, 1byte = error code: 00 = ICMP time-to-live in transit. | 95134 | IP Router timeout exceeded (from <Node X.25 Address>, line <Port Number>, info=<Info>) | warning |
| 14_0F: An error occurred on an IP Router SLL; info indicates: 1byte = free, 4bytes = IP address of router, 2bytes = SLL number in fault, 2bytes = DNIC of remote equipment, 1byte = ZO of remote equipment, 1byte = remote subscriber, 1byte = error code: 01 = fast-select configuration error, 05 = error in Call data, 0A = dynamic connection fault. | 95135 | IP Router SLL error (from <Node X.25 Address>, line <Port Number>, info=<Info>) | warning |
| 14_10: A LAN or a WAN interface is now online; info indicates: 1byte = free, 4bytes = IP address of router, 2bytes = SLL number (0 if LAN), 2bytes = DNIC of remote equipment (0 if LAN), 1byte = ZO of remote equipment (0 if LAN), 1byte = remote subscriber (0 if LAN), 1byte = local subscriber (0 if LAN), 1byte = number of SLL handler line, 1byte = encapsulation type (0 if LAN). | 95136 | LAN/WAN interface online on B/R (from <Node X.25 Address>, line <Port Number>, info=<Info>) | normal |
| 14_11: A LAN or a WAN interface is now offline; info indicates: 1byte = free, 4bytes = IP address of router, 2bytes = SLL number (0 if LAN), 2bytes = DNIC of remote equipment (0 if LAN), 1byte = ZO of remote equipment (0 if LAN), 1byte = remote subscriber (0 if LAN), 1byte = local subscriber (0 if LAN), 1byte = number of SLL handler line, 1byte = encapsulation type (0 if LAN). | 95137 | LAN/WAN interface offline on B/R (from <Node X.25 Address>, line <Port Number>, info=<Info>) | warning |
| 15_00: A Connection was established on a DLC or MFR line; the SVC is setup. | 95376 | Connection established on DLC/MFR (from <Node X.25 Address>, line <Port Number>) | normal |
| 15_01: A Connection was cleared on a DLC or MFR line; the SVC is Cleared. | 95377 | Connection cleared on DLC/MFR (from <Node X.25 Address>, line <Port Number>) | normal |
| 15_02: A frame with an unknown DLCI was received on a DLC or MFR line; the frame is ignored. | 95378 | Unknown DLCI on DLC/MFR (from <Node X.25 Address>, line <Port Number>) | minor |
| 15_03: Frame re-assembly initiation has occurred on a DLC or MFR line. | 95379 | Start frame re-assembly on DLC/MFR (from <Node X.25 Address>) | normal |
| 15_04: Transmission of re-assembled frames has stopped on a DLC or MFR line. | 95380 | Re-assembled frame transmission stopped on DLC/MFR (from <Node X.25 Address>) | normal |
| 15_05: The congestion bits are being set on a DLC or MFR line. | 95381 | Setting congestion bits on DLC/MFR (from <Node X.25 Address>) | normal |
| 15_06: Selective frame dropping is occurring on a DLC or MFR line. | 95382 | Selective frame drop on DLC/MFR (from <Node X.25 Address>) | warning |
| 15_07: All frames are being dropped on a DLC or MFR line. | 95383 | Dropping all frames on DLC/MFR (from <Node X.25 Address>) | warning |
| 15_08: Dropping all frames after data frame rejection threshold exceeded; (see parameter C2R3P0). | 95384 | Data frame rejection threshold exceeded on DLC/MFR (from <Node X.25 Address>) | warning |
| 15_10: A frame that is too short was received on a DLC or MFR line; the frame is ignored. | 95392 | Frame too short on DLC/MFR (from <Node X.25 Address>, line <Port Number>) | minor |
| 15_20: A frame too that is long was received on a DLC or MFR line; the frame is ignored. | 95408 | Frame too long on DLC/MFR (from <Node X.25 Address>, line <Port Number>) | minor |
| 15_30: A packet that is too short was received from the X.25 layer. | 95424 | Packet too short received from X.25 on DLC/MFR (from <Node X.25 Address>) | warning |
| 15_40: A packet that is too long was received from the X.25 layer. | 95440 | Packet too long received from X.25 on DLC/MFR (from <Node X.25 Address>) | warning |
| 15_50: An unexpected end of de-segmentation occurred on a DLC or MFR line; the next SEP could not be extracted due to the remaining number of bytes being less than 2. | 95456 | Unexpected end of de-segmentation on DLC/MFR (from <Node X.25 Address>) | warning |
| 15_60: The SEP extracted is inconsistent due to the length (SEP+data) being less than the remaining number of bytes. | 95472 | Extracted SEP inconsistent on DLC/MFR (from <Node X.25 Address>) | warning |
| 15_8C: A CRC error occurred on a DLC or MFR line; the frame is ignored. | 95516 | CRC error on DLC/MFR (from <Node X.25 Address>, line <Port Number>) | minor |
| 16_00: The compression function is not available on the requested VC; the VC is Cleared if compression is a required function otherwise the VC is established without compression. | 95632 | Compression not available on requested VC (from <Node X.25 Address>) | warning |
| 16_01: The compression function is enabled on the VC, in the direction from the called to the caller address; the VC is established. | 95633 | Compression enabled from called to caller on VC (from <Node X.25 Address>) | normal |
| 16_02: The compression function is enabled on the VC, in the direction from the caller to the called address; the VC is established. | 95634 | Compression enabled from caller to called on VC (from <Node X.25 Address>) | normal |
| 16_03: The compression function is enabled on the VC in both directions, to caller and to called; the VC is established. | 95635 | Compression enabled bi-directional on VC (from <Node X.25 Address>) | normal |
| 16_04: The compression function is Reset due to an internal cause; the VC is Reset. | 95636 | Compression Reset due to internal cause (from <Node X.25 Address>) | warning |
| 16_05: The compression function is Reset due to an external cause; the VC is Reset. | 95637 | Compression Reset due to external cause (from <Node X.25 Address>) | warning |
| 16_06: The data encryption function is disabled on the VC; the VC is Cleared of data encryption is a required function, otherwise the VC is established without data encryption. | 95638 | Data encryption disabled on VC (from <Node X.25 Address>) | warning |
| 16_07: The data encryption function is enabled on the VC; the VC is established. | 95639 | Data encryption enabled on VC (from <Node X.25 Address>) | normal |
| 17_01: A request to connect the line in the X.121 direction was received on a DLM line; info indicates: FF marker, E.164 address length, E.164 address, AA marker, X.121 address length, X.121 address, AA marker, MLP bundle number (FF=not significant). | 95889 | Connect line toward X.121 on DLM (from <Node X.25 Address>, line <Port Number>, info=<Info>) | normal |
| 17_02: A notification of failure to connect a switched line for either a local or remote cause was received on a DLM line. info indicates: failure source: 0=remote 1=local, E.164 address length, E.164 address, AA marker, X.121 address length, X.121 address, AA marker, MLP bundle number (FF=not significant), failure cause. | 95890 | Connect failed local or remote on DLM (from <Node X.25 Address>, line <Port Number>, info=<Info>) | warning |
| 17_03: A notification of connection completed on a switched line that is already established was received on a DLM line; info indicates: FF marker, E.164 address length, E.164 address, AA marker, X.121 address length, X.121 address, AA marker, MLP bundle number (FF=not significant). | 95891 | Connect completed on switched line on DLM (from <Node X.25 Address>, line <Port Number>, info=<Info>) | normal |
| 17_04: A notification of a switched line being assigned as part of a Destination Line changeover or reconnection was received on a DLM line; line is Destination number; info indicates: source line number, cause indication, diagnostic indication. | 95892 | Switched line assigned on DLM (from <Node X.25 Address>, line <Port Number>, info=<Info>) | normal |
| 17_05: A request to assign a Source Line for Destination Line changeover or reconnection was received on a DLM line; line is Source number; info indicates: destination line number. | 95893 | Source line requested on DLM (from <Node X.25 Address>, line <Port Number>, info=<Info>) | normal |
| 17_06: A request to close all Source Lines not in a bundle in the indicated direction was received on a DLM line; line is line number that caused Reset; info indicates: X.121 address length, X.121 address. | 95894 | Request to close SLs not in bundle on DLM (from <Node X.25 Address>, line <Port Number>, info=<Info>) | normal |
| 17_07: A notification of a software incident occurred on a DLM line; info indicates: incident number. | 95895 | Software incident on DLM (from <Node X.25 Address>, line <Port Number>, info=<Info>) | warning |
| 17_08: A notification of low threshold on a bundle occurred on a DLM line; line is bundle number; info indicates: number of lines in bundle, list of lines in bundle, FF marker. | 95896 | Low bundle threshold on DLM (from <Node X.25 Address>, line <Port Number>, info=<Info>) | normal |
| 18_00: A call was made to the Configurator (CFG); the configurator is awaiting a keyword; info indicates: call request packet. | 96144 | Configurator called in CFG (from <Node X.25 Address>, info=<Info>) | normal |
| 18_01: A CRC error occurred during configuration; the Configuration RAM is restored. | 96145 | CRC error in CFG (from <Node X.25 Address>) | warning |
| 18_02: The size of the configuration is too large; info indicates: compressed size sent. | 96146 | Configuration size too large in CFG (from <Node X.25 Address>, info=<Info>) | minor |
| 18_03: The EEPROM is being archived by the Configurator (CFG). | 96147 | EEPROM archiving in CFG (from <Node X.25 Address>) | normal |
| 18_04: The Configuration RAM is being restored. | 96148 | Configuration RAM restored in CFG (from <Node X.25 Address>) | normal |
| 18_05: A Selective Reset occurred under Configurator control. | 96149 | Selective Reset in CFG (from <Node X.25 Address>) | normal |
| 18_06: A line was created by the Configurator. | 96150 | Line creation in CFG (from <Node X.25 Address>, line <Port Number>) | normal |
| 18_07: A line was deleted by the Configurator. | 96151 | Line deletion in CFG (from <Node X.25 Address>, line <Port Number>) | normal |
| 18_08: The line type was changed by the Configurator. | 96152 | Line type changed in CFG (from <Node X.25 Address>, line <Port Number>) | normal |
| 18_09: A network Clear or abnormal Clear occurred during configuration; normal termination of PAD command includes Clear; info indicates: cause of Clear, diagnostic of Clear. | 96153 | Network Clear in CFG (from <Node X.25 Address>, info=<Info>) | normal |
| 18_10: The configuration RAM was copied to the operational RAM on the indicated module. | 96160 | Configuration RAM copied to operational RAM in CFG (from <Node X.25 Address>, module <Port Number>) | normal |
| 18_14: Download to the indicated module was refused by the Configurator due to an unauthorized user access. | 96164 | Download refused: unauthorized user in CFG (from <Node X.25 Address>, module <Port Number>) | warning |
| 18_15: Download to the indicated module was refused by the Configurator due to no buffer memory being available. | 96165 | Download refused: no buffers in CFG (from <Node X.25 Address>, module <Port Number>) | minor |
| 18_16: Download to a module was initiated by the Configurator. | 96166 | Download initiated in CFG (from <Node X.25 Address>) | normal |
| 18_17: Download to the indicated module was terminated by the Configurator. | 96167 | Download terminated in CFG (from <Node X.25 Address>, module <Port Number>) | normal |
| 18_18: Download to a module was completed without error by the Configurator. | 96168 | Download completed without error in CFG (from <Node X.25 Address>) | normal |
| 18_19: Download to the indicated module was refused by the Configurator due to no memory resources and maximum RAM size is less than 2MB. | 96169 | Download refused: no RAM in CFG (from <Node X.25 Address>, module <Port Number>) | minor |
| 18_1E: A System Reset of the indicated module was initiated by the Configurator from the Flash PROM copy of the software. | 96174 | System Reset initiated from FPROM in CFG (from <Node X.25 Address>, module <Port Number>) | normal |
| 18_1F: A System Reset of the indicated module was initiated by the Configurator from the RAM copy of the software. | 96175 | System Reset initiated from RAM in CFG (from <Node X.25 Address>, module <Port Number>) | normal |
| 18_20: A download or upload of a configuration was initiated by the Configurator. | 96176 | Configuration download or upload initiated in CFG (from <Node X.25 Address>) | normal |
| 19_00: A reception error occurred on a frame in the Configurator; the frame is ignored. | 96400 | Reception error on frame in CFG (from <Node X.25 Address>) | minor |
| 19_01: A protocol error occurred on a frame in the Configurator; the frame is ignored. | 96401 | Protocol error in CFG (from <Node X.25 Address>) | minor |
| 19_02: A reliability error occurred on a frame in the Configurator. | 96402 | Reliability error in CFG (from <Node X.25 Address>) | minor |
| 19_03: Transfer of configuration data is enabled by the Configurator. | 96403 | Data transfer enabled in CFG (from <Node X.25 Address>) | normal |
| 19_04: Transfer of configuration data is disabled by the Configurator. | 96404 | Data transfer disabled in CFG (from <Node X.25 Address>) | warning |
| 19_05: Transmission of configuration data encountered an error; interface clocking may be the wrong rate or not connected. | 96405 | Transmission error in CFG (from <Node X.25 Address>) | warning |
| 19_06: A DLCI was not configured due to the PLL structure not being found. | 96406 | DLCI not configured in CFG (from <Node X.25 Address>) | warning |
| 19_07: An event occurred relating to the PLL structure in the Configurator. | 96407 | PLL structure event in CFG (from <Node X.25 Address>) | warning |
| 19_09: There is an inconsistency in the CLASS 13 configuration; the default values from Profile 84 are used. | 96409 | CLASS 13 inconsistency in CFG (from <Node X.25 Address>) | minor |
|
|