AXIS Command Line Interface

The preferred tool for configuring, monitoring, and controlling an AXIS shelf is StrataView Plus. However, the command line interface provides access to features that exist on the AXIS shelf but are not yet accessible through StrataView Plus. Also, when alarm conditions or other unwanted situations occur, the command line interface provides a lower level of access to the cards that StrataView Plus does not provide.

The AXIS commands in the table that follows are divided by major functional group. The table shows the complete name of the command, the cards from which the command can be invoked, and the page number of the command description. For more elaborate or supplemental information on the service module or ATM commands, refer to the sections in this manual that describe the service module and ATM commands. Also, the Cisco StrataCom System Overview provides conceptual information on the Cisco implementation of frame relay and ATM.

The command line prompt shows the name of the shelf, the number of the shelf (which is always "1"), the slot number and type of the current card, and whether the card is in the active or standby state ("a" or "s"). The following is an example of the command line prompt:

kanchend.1.6.AUSM.a >

In this case, the current card is an active-state AUSM card in slot 6, and the name of the shelf in "kanchend."

The command notation and argument parameters follow standard programming convention: a space separates the command and each parameter; required arguments are enclosed in "<>" marks; and optional parameters are enclosed in square brackets ("[ ]"). A vertical bar (|) represents the OR function.

Note When commands are entered with no parameters, a usage message appears, which shows syntax and valid ranges.

Table 1-1: Command List

Command	Description	ASC	SRM-3T3	FRSM	AUSM	CESM	IM-ATM
*Shelf Group*
clrcderrs	Clear Card Errors in BRAM	X		X	X		X
clrsmcnf	Clear Service Module Configuration
dspcderrs	Display Card Errors in BRAM	X		X	X		X
resetcd	Reset Card	X
dspcd	Display Card	X		X	X	X	X
dspcds	Display Cards	X	X
switchcc	Switch Core Cards	X
cnftrapmgr	Configure/Add/Delete Trap Managers	X
dsptrapmgr	Display Trap Managers	X
clrbnmcnt	Clear BNM Cell Counter	X
dspbnmcnt	Display BNM Cell Counter	X
dspintvl	Display BNM-155 Interval	X
cnfbnmif	Configure BNM-155 Interface	X
dspbnmif	Display BNM-155 Interface	X
cnfclksrc	Configure Network Clock Source	X			X		X
dspclksrc	Display Current Clock Source	X			X		X
clrmsgcnt	Clear Control Message Counter	X		X	X	X	X
dspmsgcnt	Display Control Message Counter	X		X	X	X	X
dspsmcnf	Display Service Module Configuration
version	Version (displays version data for a card)	X		X	X	X	X
*User Group*
adduser	Add User	X
cc	Change Card	X		X	X	X	X
clrscrn	Clear Terminal Screen	X		X	X	X
clrlog	Clear Event/Message Log	X
cnfpwd	Configure Password	X
deluser	Delete User	X
dsplog	Display Event/Message Log	X
dspusers	Display Users	X
Help	Help (list of commands per card)	X		X	X	X	X
users	Users	X
*Node Group*
cnfname	Configure Shelf Name	X
cnfdate	Configure Date	X
cnftime	Configure Time	X
cnftmzn	Configure Time Zone	X
cnftmzngmt	Configure Time Zone to GMT	X
cnfifip	Configure LAN interface IP	X
dspifip	Display LAN interface IP	X
dspmaptbl	Display Map Table			X	X
addred	Add Redundancy	X
delred	Delete Redundancy	X
dspred	Display Redundancy	X
*Alarm Group*
clralm	Clear Alarms on the Card	X	X	X	X	X	X
clralms	Clear All Alarms			X	X	X	X
dspalm	Display Alarms for a Line	X	X	X	X	X	X
dspalms	Display All Alarms on Card	X	X	X	X	X	X
dspalmcnf	Display Alarm Threshold Configuration	X	X	X	X	X	X
clralmcnt	Clear Alarm Counters/Statistics	X	X	X	X	X	X
dspalmcnt	Display Alarm Counters/Statistics (line)	X	X	X	X	X	X
dspshelfalm	Display Shelf Alarms	X
*Line Group*
addln	Add Line (T1, E1, or T3)		X	X	X	X	X
cnfln	Configure Line			X	X	X	X
delln	Delete Line		X	X	X	X	X
dspln	Display Line Configuration	X		X	X	X	X
dsplns	Display All Lines on Card	X		X	X	X	X
dspsrmlns	Display All Lines on Card		X
addlnloop	Add Line Loop				X	X	X
dellnloop	Delete Line Loop				X	X	X
*Port Group*
addport	Add Port			X
cnfport	Configure FR Port(s)			X	X
cnfportq	Configure AUSM port queue				X
copyports	Copy Port Configuration			X	X
delport	Delete FR Port			X
delports	Delete Port Configurations			X	X
dspport	Display Port Configuration			X	X
dspports	Display All Ports			X	X
dspportstats	Display Port Statistics			X
clrportcnt	Clear Port Counters			X	X
clrportcnts	Clear Port Counters			X	X
dspportcnt	Display FR Port Counters			X	X
upport	Up Port				X
dnport	Down Port				X
dspportq	Display Port Queue				X		X
dspportqs	Display Port Queues				X
cnfilmi	Configure ILMI				X
dspilmi	Display ILMI				X
dspilmicnt	Display ILMI Counters				X
*Channel Group*
addchan	Add Channel			X		X
addchanloop	Add a Channel Loopback			X	X	X
clrsarcnt	Clear SAR Counters	X		X	X	X
copychans	Copy Channel Configurations			X	X
delchan	Delete Channel(s)			X		X
delchanloop	Delete a Channel Loopback			X	X	X
delchans	Delete Channels			X	X
dspchan	Display Channel Configuration			X		X
dspchans	Display All Channels			X		X
dspchancnt	Display Channel Counters			X	X	X	X
dspchstats	Display Channel Statistics			X
dspsarcnt	Display SAR Counters	X		X	X	X
clrchancnt	Clear Channel Counter for FR Channels			X	X	X	X
clrchancnts	Clear Channel Counter for FR Channels			X	X	X
cnfchanpol	Configure Channel Policing			X
cnfchanfst	Configure Channel ForeSight			X	X
cnfchanq	Configure Channel Queue				X
*Connection Group*
addcon	Add Connection				X
delcon	Delete Connection				X
dspcon	Display Connection				X
dspcons	Display Connections				X
dsploads	Display Loads				X
cnfupcabr	Configure ABR				X
cnfupccbr	Configure CBR				X
cnfupcvbr	Configure VBR				X
tstcon	Test Connection			X	X	X
tstconseg	Test Connection Segment				X
tstdelay	Test Delay			X	X	X
*IMATM Group*
addaimgrp	Add AIM Group						X
addlns2aimgrp	Add Lines to AIM Group						X
clraimgrpcnt	Clear AIM Group Count						X
cnfaimgrp	Configure AIM Group						X
delaimgrp	Delete AIM Group						X
dellnsfmaimgrp	Delete Lines from AIM Group						X
dspaimgrp	Display AIM Group						X
dspaimgrpcnt	Display AIM Group Count						X
dspaimgrps	Display AIM Groups						X
dspds3ln	Display DS3 Line						X
dspds3lns	Display DS3 Lines						X
SRM-3T3 Group
addlink	Add an SRM-3T3 T3 link to a T1slot and line		X
clrsrmcnf	Clear SRM-3R3 configuration		X
cnfsrmclksrc	Configure SRM-3T3 clock source		X
dellink	Delete an SRM-3T3 T3 link to a T1slot and line		X
delslotlnk	Delete a link from a T1 slot		X
dsplink	Display an SRM-3T3 T3 link to a T1slot and line		X
dspslotlnk	Display a link in a T1 slot		X
dspsrmclksrc	Display SRM-3T3 clock source		X
BERT Group
cnfbert	Configure bit error rate test (BERT)
delbert	Delete bit error rate test (BERT)
dspbert	Display bit error rate test (BERT)
modbert	Modify bit error rate test (BERT)
startbert	Start bit error rate test (BERT)

addaimgrp

This command adds an AIMUX group.

Full Name

Add AIM group

Syntax

addaimgrp <aimux_grp> <list_of_lines>

<aimux_grp>	is the AIMUX group number to be added (1..8)
<list of lines>	is the list of physical lines to be included in "aimux_grp" separated by dots

For example: addaimgrp "2 3.4.5" (Adds AIMUX group 2 with lines 3, 4, and 5)

Related Commands

delaimgrp, cnfaimgrps, dspaimgrp, dspaimgrps

Cards on which the command executes

IM-ATM

Attributes

Log: Yes State: Active Privilege: 1-2

Note There should not be any ATM UNI ports established with the same "port_n" since ATM ports and AIMUX groups both share the same set of port numbers.

addlns2aimgrp

This command adds lines to an existing AIMUX group.

Full Name

Add lines to an AIM group

Syntax

addlns2aimgrp <aimux_grp> <list_of_lines>

<aimux_grp>	is the AIMUX group to which lines should be added (1..8)
<list_of_lines>	is the list of lines in the AIMUX group separated by dots.

Example: addlns2aimgrp "2 1.2" (Adds lines 1 and 2 to an existing AIMUX group number "2")

Related Commands

dellnsfmaimgrp

Cards on which the command executes

IM-ATM

Attributes

Log: Yes State: Active Privilege: 1-2

addchan

Add a channel to the current FRSM.

No messages appear on screen after command entry unless the command cannot execute as entered.

Full Name

Add channel

Syntax

addchan <chan_num> <port_num> <dlci_num> <cir> <chan_type>

where:

<chan_num>	channel number is in the range 16-271
<port_num>	port number is in the range 1-96
<dlci_num>	DLCI is in the range 0-1023
<cir>	committed information rate: 0-1536000 bps for T1; 0-2048000 bps for E1
<chan_type>	channel type has a range of 1-5, and their meaning is: 1=NIW, 2=SIW-transparent, 3=SIW-xlation, 4=FUNI, 5=frame forwarding

Possible errors are:

illegal/invalid parameters
channel already exists
port not enabled

Related Commands

delchan, dspchan, dspchans

Cards on which the command executes

FRSM, CESM

Attributes

Log: Yes State: Active Privilege: 1-2

addchanloop

Add a channel loopback to the current FRSM or AUSM. Causes the channel to loop at the SAR (segmentation and reassembly) stage.

No messages appear on screen after command entry unless the command cannot execute as entered.

Full Name

Add a channel loopback

Syntax

addchanloop <chan_num>

where:

<chan_num>

channel number is in the range 16-271

Related Commands

delchanloop, tstcon, tstdelay

Cards on which the command executes

FRSM, AUSM, CESM

Attributes

Log: Yes State: Active Privilege: 1-4

addcon

Add a connection to the current AUSM.

No messages appear on screen after command entry unless the command cannot execute as entered.

Full Name

Add connection

Syntax

addcon <channel number> <connection type> <port number> <vpi> <vci> <service type> <egress queue number>

where:

<channel number>	channel number has a range of 16-271
<connection type>	connection type is either 1 for VPP or 2 for VCC
<port number>	port number is in the range 1-4
<vpi>	vpi has a value in the range 0-255
<vci>	vci has a value in the range 0-65535
<service type>	service type can be: 1 = CBR, 2 = VBR, and 3 = ABR
<egress queue number>	the egress queue number can be specified as 1-12 and 0 is for the default in addcon

Related Commands

delcon, dspcons, dspcon

Cards on which the command executes

AUSM

Attributes

Log: Yes State: Active Privilege: 1-2

Example 1 Description

addcon 16 2 1 1 1 3 1

Add a VCC connection to channel 16 on port 1 with vpi=1, vci=1, ABR service type, and an egress queue number of 1

addlink

The addlink command adds a link between a T1 line within a T3 line on a SRM-3T3 card and a slot and line number on a T service module.

Full Name

Add link

Syntax

addlink <T3 line number> <T1 line number> <Number of T1s> <Target Slot number> <Slot line number>

where:

<T3 Line number>	the SRM-3T3 T3 line number (range 1-3)
<T1 line number>	the start T1 line number within the T3 line (range 1-28)
<Number of T1s>	the number of T1s to be linked (range 1-8)
<Target slot number>	the T1 service module slot number to be linked
<Slot line number>	the T1 line number in the slot to be linked (range 1-4 or 1-8) depending upon the ports in the service module

Related Commands

dsplink, dellink

Cards on which the command executes

SRM-3T3

Attributes

Log: No State: Active Privilege: 1

addln

The addln command adds a T1, E1, or T3 line to the current card.

Full Name

Add line

Syntax

addln <line number>

Related Commands

cnfln, delln, dspln

Cards on which the command executes

FRSM, AUSM, SRM-3T3, CESM, IM-ATM

Attributes

Log: No State: Active Privilege: 1

Example 1 Description System Response

addln 1

Add a line numbered 1 to the current card (AUSM, FRSM, CESM, IM-ATM, or SRM-3T3)

addlnloop

This command puts a T1 or E1 line in a loopback state for the current card.

Full Name

Add line loop

Syntax

addlnloop <line number>

where:

value from 1-8 used for AUSM-8T/8E1 and IMATM

Related Commands

dellnloop

Cards on which the command executes

AUSM, FRSM, CESM, IM-ATM

Attributes

Log: Yes State: Active Privilege: 1

addport

The addport command adds a service port to the shelf's configuration.

The screen does not display a message after successful command entry.

Full Name

Add a port

Syntax

addport <port_num> <line_num> <ds0_speed> <begin_slot> <num_slot> <port_type>

where:

<port_num>	numbers in the range 1-96 are valid
<line_num>	value ranging from 1 to 4
<ds0_speed>	1 for 56K, 2 for 64K
<begin_slot>	beginning timeslot number in the T1 or E1 frame
<num_slot>	number of consecutive timeslots in the T1 or E1 frame
<port_type>	is either 1, 2, or 3: 1 = frame relay, 2 = FUNI, 3=frame forwarding

Related Commands

addportlpbk, cnfport, delport, dspport, dspports

Cards on which the command executes

FRSM

Attributes

Log: Yes State: Active Privilege: 1

addred

This command links two AXIS slots (a primary slot and a secondary slot) so that like cards in these slots are treated as a redundant pair of cards. Redundancy can be 1:1 or 1:N, if 1:N, one secondary slot must be linked to N primary slots through multiple execution of this command.

Full Name

Add Redundancy

Syntax

addred <PrimarySlotNum> <SecondarySlotNum> <RedType>

where:

<PrimarySlotNum>	the slot number of the slot containing the primary card of the card pair. Range = 5-14
<SecondarySlotNum>	the slot number of the slot containing the secondary card of the card pair. Range = 12-14
<RedType>	the type of redundancy. 1 = 1:1, 2 = 1:N

Related Commands

dspred, delred

Cards on which the command executes

ASC

Attributes

Log: No State: Active Privilege: 1-6

adduser

Add a user to the shelf configuration. The added user cannot have a privilege level that is higher than the current user. No screen output appears unless an error in the input occurred.

Full Name

Add user

Syntax

adduser <user ID> <privilege level>

where:

<user ID>	a name for the user
<privilege level>	privilege is the highest level of access the user has

Related Commands

dspusers, deluser

Cards on which the command executes

ASC

Attributes

Log: No State: Active Privilege: 1-6

cc

Changes the card into which the user is logged. If a card slot is empty, an error message appears.

Full Name

Change card

Syntax

cc <slot number>

where:

is the card slot to which the screen display should change

Related Commands

switchcc

Cards on which the command executes

ASC, FRSM, AUSM, CESM, IM-ATM

Attributes

Log: No State: Any state Privilege: 1-6

clraimgrpcnt

This command clears all the AIMUX related counters for all lines in an AIMUX group.

Full Name

Clear AIM group count

Syntax

clraimgrpcnt <aimux_grp>

where:

<aimux_grp>

is the AIMUX group number

Related Commands

delaimgrpcnt

Cards on which the command executes

IM-ATM

Attributes

Log: Yes State: Active Privilege: 1-2

clralm

The clralm command clears alarms on a specified line on the current card. Alarms occurring after this command executes are not affected. If alarms on a line are cleared with this command, the results may be observable through the dspalm command

This command can clear alarms caused only by the collection of statistical data. Alarms caused by network failure cannot be cleared. For example, an alarm caused by a collection of bipolar errors can be cleared, but an alarm caused by a card failure cannot.

Full Name

Clear alarm

Syntax

For an ASC:

clralm <-ds3> <LineNum>

-ds3 <LineNum>

where LineNum = 1-n, n = 1 if BNM

clralm <-e3> <LineNum>

-e3 <LineNum>

where LineNum = 1-n, n = 1 if BNM

clralm <-plcp> <PLCPNUM>

-plcp <PLCPNum>

where PLCPNum = 1-n, n = 1 if BNM

For an FRSM:

clralm <-ds1> <LineNum>

where

LineNum = 1-n, n = 4 if FRSM

For an SRM-3T3:

clralm <-srmds3> <LineNum>

where

LineNum = 1-n, n = 3 if SRM-3T3

Related Commands

clralms, dspalm, dspalms

Cards on which the command executes

ASC, FRSM, AUSM, SRM-3T3, CESM, IM-ATM

Attributes

Log: No State: Any Privilege: 1-5

clralmcnt

The clralmcnt command clears all the alarm counters and statistics on the specified line on the current card. All counters are reset to zero. The terminal does not display a response unless an error exists in the syntax.

Full Name

Clear alarm counters/statistics

Syntax

clralmcnt <-ds3 LineNum> |<-e3 LineNum> | <-plcp PLCPNum> | <-ds1 LineNum>

where:

On an ASC with BNM-T3, <-ds3 LineNum> and <-plcp PLCPNum> and <-e3 LineNum> = 1

On an FRSM, <-ds1 LineNum> is in the range 1-4.

On an AUSM, <-ds1 LineNum> is in the range 1-4.

On an SRM-3T3, <-srmds3 LineNum> is in the range 1-3.

On AXIS shelf configured with BNM-155, the syntax is:

clralmcnt -sonet <LineNum>

Related Commands

dspalmcnt, clralmcnts

Cards on which the command executes

ASC, FRSM, AUSM, SRM-3T3, CESM, IM-ATM

Attributes

Log: No State: Any Privilege: 1-5

clralmcnts

The clralmcnts command clears all the alarm counters and statistics on the current card. All counters are reset to zero. The terminal does not display a response unless an error exists in the syntax.

Full Name

Clear all alarm counters/statistics on the current card.

Syntax

clralmcnts

Related Commands

dspalmcnt, clralmcnt

Cards on which the command executes

ASC, FRSM, AUSM

Attributes

Log: No State: Any Privilege: 1-5

clralms

The clralm command clears alarms on the current card. Alarms occurring after this command executes are not affected.

Full Name

Clear alarms on card

Syntax

For FRSM and AUSM
clralm <-ds1> <LineNum>

where:

LineNum = 1-4

ASC, FRSM, AUSM, IM-ATM

Attributes

Log: No State: Any Privilege: Superuser

clrchancnt

This command clears the channel counters for a specified frame relay channel on an FRSM or AUSM. Counting resumes after the command executes.

Full Name

Clear channel counters

Syntax

clrchancnt <channel number>

where:

is in the range 16-271

Related Commands

dspchan, clrchancnts, dspchancnt

Cards on which the command executes

FRSM, AUSM, CESM, IM-ATM

Attributes

Log: No State: Any Privilege: 1-5

The frame relay counters for each channel are:

Received frames
Received bytes
Received frames DE
Received bytes DE
Received frames discarded
Received bytes discarded
Received frames discarded for shelf alarms
Received frames discarded for exceeded queue depth
Received bytes discarded for exceeded queue depth
Received frames discarded for exceeded DE threshold
Received frames FECN
Received frames BECN
Received frames tagged FECN
Received frames tagged BECN
Received frames tagged DE
Transmitted frames
Transmitted bytes
Transmitted frames BECN
Transmitted frames FECN
Transmitted frames DE
Transmitted bytes DE
Transmitted frames discarded
Transmitted bytes discarded
Transmitted frames discarded for exceeded queue depth
Transmitted bytes discarded for exceeded queue depth
Transmitted frames discarded for exceeded DE threshold
Transmitted frames discarded for physical layer fail
Transmitted frames discarded for CRC error
Transmitted frames discarded for reassembly failure
Transmitted frames discarded for source abort
Transmitted frames during LMI logical port alarm
Transmitted bytes during for LMI logical port alarm
Transmitted frames tagged FECN
Transmitted frames tagged BECN

clrchancnts

The clrchancnts command clears the channel counter for all frame relay channels on the current FRSM. Counting resumes for frame relay transmissions occurring after the command executes. For a list of the frame relay counters, refer to the description of clrchancnt.

Full Name

Clear channel counters

Syntax

clrchancnts

Related Commands

dspchan, clrchancnt, dspchancnt

Supported Cards

FRSM, AUSM, CESM

Cards on which the command executes

FRSM, AUSM

Attributes

Log: No State: Any Privilege: 1-3

clrlog

The clrlog command clears the error/event message log. The log resumes updating after this command executes.

Full Name

Clear event/message log

Syntax

clrlog

Related Commands

dspslog

Cards on which the command executes

ASC, FRSM

Attributes

Log: No State: Any Privilege: 1

clrmsgcnt

The clrmsgcnt command clears the control message counters. The control message counters are as follows:

Number of control Frames transmitted to SAR (from RISC) maintained by RISC
Number of control Frames received from SAR (to RISC) maintained by RISC
Number of control Frames transmitted to RISC from SAR maintained by SAR (should be equal to (riscRcvCtrlMsg)
Number of control Frames received to SAR from RISC maintained by SAR (should be equal to (riscXmtCtrlMsg)
Total control (management) cells discarded due to illegal length error
Total control (management) cells discard due to illegal CRC error
Count of discarded control message due to unknown channel error
The control cell header Rcvd of the last unknown channel

Full Name

Clear control message counter

Syntax

clrmsgcnt

Related Commands

dspmsgcnt

Cards on which the command executes

ASC, FRSM, AUSM, CESM, IM-ATM

Attributes

Log: No State: Any Privilege: 1-5

clrportcnt

The clrportcnt command is used to clear the values of a port's counter on the current AUSM or FRSM.

No message appears upon successful execution of the command.

Full Name

Clear port count

Syntax

clrportcnt <port number>

where:

On an AUSM, <port number> is in the range 1-4.

On an FRSM, <port number> is in the range 1-96.

Related Commands

clrportcnts, dspportcnt

Cards on which the command executes

FRSM, AUSM

Attributes

Log: No State: Any Privilege: 1-5

clrportcnts

The clrportcnts command clears all port counts on the current FRSM or AUSM.

No messages appear on screen after command entry unless the command cannot execute as entered.

Full Name

Clear port counts

Syntax

clrportcnts

Related Commands

clrportcnt, dspportcnt

Cards on which the command executes

FRSM, AUSM

Attributes

Log: No State: Any Privilege: 1-5

clrsarcnt

The clrsarcnt command clears the Segmentation and Reassembly (SAR) counters. The SAR counters are:

Number of cells transmitted on this channel.
Number of CLP cells that were transmitted on this channel.
Number of AIS cells that were transmitted on this channel.
Number of FERF cells that were transmitted on this channel.
Number of BCM cells that were transmitted on this channel.
Number of End2End loop cells that were transmitted on this channel.
Number of segment loop cells that were transmitted on this channel.
Number of cells discard due to Shelf alarm on this channel.
Number of cells that were received on this channel.
Number of CLP cells that were received on this channel.
Number of AIS cells that were received on this channel.
Number of FERF cells that were received on this channel.
Number of BCM cells that were received on this channel.
Number of End2End loop cells that were received on this channel.
Number of segment loop cells that were received on this channel.
Number of cells that had the CRC error on this channel.

Cards on which the command executes

SRM-3T3

Attributes

Log: No State: Any Privilege: 1-6

clrsmcnf

The clrsmcnf command clears configuration elements for all the service modules on the shelf. The elements this command clears are as follows:

The existence of a configuration
Whether rate control is on or off
Whether the card is channelized
The number of the MIB version

Full Name

Clear service module configuration

Syntax

clrsmcnf

Related Commands

dspsmcnf

Cards on which the command executes

ASC

Attributes

Log: Yes State: Active Privilege: 1-2

cnfbert

The cnfbert command configures the shelf for bit error rate testing.

Full Name

Configure Bit Error Rate Test

Syntax

cnfbert

Arguments for this command are supplied by entering or selecting values in a series of menus. The cnfbert command has numerous combinations of menu screens. Based on a choice made at one menu, the choices available at the menus that follow would differ. However, to describe the command the following example is typical.

axis1.1.3.ASC.a > cnfbert

The system response is:

** T1/E1 DIAGNOSTIC TESTS PACKAGE **

====================================

This is a package of Bit Error Rate Tests as well as other associated operations such as loopbacks. This package is menu driven and can be used for any T1/E1.

Service Module in the shelf.

TEST CONFIGURE MENU
===================

SLOT NUMBER
r. Redo From Start
p. Previous Menu
q. Quit Menu

Slot number to configure test please (5-14): 6

TEST MEDIUM

r. Redo From Start
p. Previous Menu
q. Quit Menu

1. Port
2. Line

Please Enter Choice[1-2]: 1

PORT

r. Redo From Start
p. Previous Menu
q. Quit Menu

Port number to test please: 4

TEST TYPE

r. Redo From Start
p. Previous Menu
q. Quit Menu

1. BERT Pattern Test
2. DDS Seek
3. Loopback

Please Enter Choice[1-3]: 1

DEVICE TO LOOP

r. Redo From Start
p. Previous Menu
q. Quit Menu

1. Latching DS0-DP drop Device
2. Latching DS0-DP line Device
3. Latching OCU Device
4. Latching CSU Device
5. Latching DSU Device
6. Latching HL96 Device
7. V.54 polynomial Loopback
8. No Loopback

Please Enter Choice[1-8]: 4

BERT PATTERN

r. Redo From Start
p. Previous Menu
q. Quit Menu

1. All Zeroes Pattern
2. All Ones Pattern
3. Alternate One Zero Pattern
4. Double One Zero Pattern
5. 2^15-1 Pattern
6. 2^20-1 Pattern
7. 2^20-1 QRSS Pattern
8. 2^23-1 Pattern
9. 1 in 8 Pattern
10. 3 in 24 Pattern
11. DDS-1 Pattern
12. DDS-2 Pattern
13. DDS-3 Pattern
14. DDS-4 Pattern
15. DDS-5 Pattern
16. 2^9 Pattern
17. 2^11 Pattern

Please Enter Choice[1-17]: 3

TEST CONFIGURATION

Physical Slot Number : 6
Logical Slot Number : 6
Port Number: 4
Test Type: BERT Pattern Test
Device To Loop: Latching CSU Device
BERT Pattern : Alternate One Zero Pattern

r. Redo From Start
p. Previous Menu
q. Quit Menu

This test is intrusive of the data traffic.

Do you want to continue the test configuration? (y/n): y

Test configured.

Related Commands

dspbert, modbert, delbert

Cards on which the command executes

ASC

cnfbnmif

The cnfbnmif command configures the interface format for the BNM-155 trunk card.

Full Name

Configure BNM Interface

Syntax

cnfbnmif -if <interface format>

where:

interface format is

Related Commands

dspbnmif

Cards on which the command executes

ASC

cnfchanfst

The cnfchanfst command configures the ForeSight parameters for a frame relay or ATM channel. No messages appear on the screen unless an error occurs.

Full Name

Configure channel ForeSight

Syntax

For FRSM:

cnfchanfst <chan_num> <fst_enable> <mir> <pir> <qir>

where:

<chan_num>	channel number range is 16-271
<fst_enable>	ForeSight Enable--1 for enable, 2 for disable
<mir>	minimum rate--10-8000 in cell/sec, default 1000
<pir>	peak rate--10-8000 in cell/sec, default 1000
<qir>	quiescent rate--10-8000 in cell/sec, default 1000

For AUSM:

cnfchanfst <chan_num> <enable | disable> <fgcra_enable> <ibs> <pcr> <mcr> <icr>

where:

<chan_num>	channel number range is 16-271
<enable \| disable>	enable/disable pertains to Foresight: 1 = disable, 2 = enable
<fgcra_enable>	FGCRA enable is for the specified channel: 1 = disable, 2 = enable
<ibs>	ibs is the initial burst size in the range 10-5000 cells
<pcr>	pcr is the peak cell rate in the range 11-8000 cells/second
<mcr>	mcr is the minimum cell rate in the range 11-8000 cells/second
<icr>	icr is the initial cell rate in the range 11-8000 cells/second

Related Commands

dspchan

Cards on which the command executes

FRSM, AUSM

Attributes

Log: Yes State: Active Privilege: 1-2

cnfaimgrp

This command configures the parameters of an AIMUX group.

Full Name

Configure AIM group

Syntax

cnfaimgrp <aimux_grp> -rwdiff <read_wr_ptr_diff> -severity <link_loss_severity> -maxdiff <maximum_diff_delay> -red <num_red_links>

where:

<aimux_grp>	is the AIMUX group number for this group (1..8)
<read_wr_ptr_diff>	is the difference between the read and write pointer maintained (1..8)
<link_loss_severity>	is the seriousness of a single link failure (1: m)
<maximum_diff_delay>	is the maximum tolerable differential delay between (range TBD)
<num_red_links>	is the number of redundant links in the AIMUX group

Related Commands

addaimgrp, delaimgrp, dspaimgrp, dspaimgrps

Cards on which the command executes

IM-ATM

Attributes

Log: Yes State: Active Privilege: 1-2

Note Redundant link(s) indicates the number of link(s) the system can lose without bringing down the AIMUX group. However, the link_loss_severity option overrides this feature.

The <read_wr_ptr_diff> value cannot be decreased from its existing value-- it can only be increased (this is because decreasing the <read_wr_ptr_diff> in an established AIMUX group involves dropping cells that are stored in the delay compensation buffer.

cnfchanpol

The cnfchanpol command configures the frame relay parameters for a channel. No messages appear on screen unless an error occurs.

Full Name

Configure channel policing

Syntax

cnfchanpol <chan_num> <cir> <bc> <be> <ibs> <detag>

where:

<chan_num>	value ranging from 16 to 271
<cir>	0-1536000 bps for T1, 0-2048000 bps for E1
<bc>	0-65535 in bytes
<be>	0-65535 in bytes
<ibs>	0-65535 in bytes. Less than or equal to Bc
<detag>	1 for enable, 2 for disable

Related Commands

dspchan

Cards on which the command executes

FRSM

Attributes

Log: Yes State: Active Privilege: 1-2

cnfchanq

The cnfchanq command configures a channel's queue parameters on the current AUSM. No messages appear on screen unless an error occurs.

Full Name

Configure channel queue

Syntax

cnfchanq <chan_num> <vc_q_depth> <clp_thresh_high> <clp_thresh_low> <efci_thresh>

where:

<chan_num>	is in the range 16-271
<vc_q_depth>	Ingress Q Depth: 0-8000 Cells
<clp_thresh_high>	CLP Threshold High: 1-8000 Cells
<clp_thresh_low>	CLP Threshold Low: 1-8000 Cells
<efci_thresh>	EFCI Threshold: 1-8000 Cells

Related Commands

dspchan

Cards on which the command executes

AUSM

Attributes

Log: Yes State: Active Privilege: 1-2

cnfclksrc

Configures primary, secondary, or internal clock source. Any combination of clocks are configurable and in any order.

Full Name

Configure clock source

Syntax

cnfclksrc -pri <PrimaryClockSource> -sec <SecondaryClockSource> -cur <CurrentClockSource> -imp <ExternalClockSourceImpedance>

where:

-pri <PrimaryClockSource> where PrimaryClockSource = 1-3
1: Internal 2: BNM Inband 3: External
-sec <SecondaryClockSource> where SecondaryClockSource = 1-3
1: Internal 2: BNM Inband 3: External
-cur <CurrentClockSource> where CurrentClockSource = 1-3,
1: Primary 2: Secondary 3: Internal
-imp <ExternalClockSourceImpedance > where ExternalClockSourceImpedance = 2-3
2: 100 ohms, 3: 120 ohms

Related Commands

dspclksrc

Cards on which the command executes

ASC, AUSM, IM-ATM

Attributes

Log: Yes State: Active Privilege: 1

cnfdate

The cnfdate command configures the date.

Full Name

Configure date

Syntax

cnfdate <mm/dd/yy>

Related Commands

none

Cards on which the command executes

ASC

Attributes

Log: Yes State: Active Privilege: Superuser

Example 1 Description

cnfdate 11/24/95

Configure the date to be 11/24/95

System Response

kanchend.1.3.ASC.a > cnfdate 11/24/95
  Date = 11/24/95

cnfifip

The cnfifip command configures the interface address. The configurable addresses are for LAN, Inband ports, and ATM.

Full Name

Configure interface address

Syntax

cnfifip -ip <IP address> -if <Interface> -msk <NetMask> -bc <BroadcastAddress>

where:

-ip <IP address>	where IP address = nnn.nnn.nnn.nnn,
-if <Interface>	where Interface is as follows:
	· 26 for Ethernet
	· 28 for Slip
	· 37 for ATM
-msk <NetMask>	where NetMask = nnn.nnn.nnn.nnn,
-bc <BroadcastAddress>	where BroadcastAddress = nnnnnnnnnnnn (hexadecimal)

Related Commands

dspifip

Cards on which the command executes

ASC

Attributes

Log: Yes State: Active Privilege: Superuser

Example 1 Description

cnfifip -ip 192.169.3.18 -if 28 -msk 255.255.255.000 -bc 192.169.3.18

Configure the IP address of the card. See example screen for cnfifip.

cnfilmi

The cnfilmi command configures a port's local management interface. No messages appear on screen unless an error occurs.

Full Name

Configure ilmi

Syntax

cnfilmi <port_num> <signal_type> <vpi> <vci> <scr> <trap_enable> <min_trap_int> <keep_alive>

where:

<port_num>	is a port number in the range 1-4
<signal_type>	is the signalling type: 1 = other, 2 = no signalling, and 3 = ILMI
<vpi>	is the virtual path identifier in the range 0-259
<vci>	is the virtual circuit identifier in the range 0-65535
<trap_enable>	is the ILMI trap enable: 1 = disable, 2 = enable
<min_trap_int>	is the minimum trap interval in the range 1-10 secs.
<keep_alive>	is the enable for Keep Alive Polling: 1 = disable, 2 = enable

Related Commands

dspilmi, dspilmicnt

Cards on which the command executes

AUSM

Attributes

Log: Yes State: Active Privilege: 1

cnfln

The cnfln command configures a line on the current card to be either T1 or E1. If the command line does not include the E1 signalling parameter, the line is a T1.

Full Name

Configure line

Syntax

cnfln <line_num> <line_code> <line_len> <clk_src> [E1-signalling]

where:

<line_num>	values in the range 1-4
<line_code>	line coding: 2 for B8ZS, 3 for HDB3, 4 for AMI
<line_len>	line length: 1-7 for T1, 8-9 for E1
<clk_src>	clock source: 1 for loop clock; 2 for local clock
[E1-signalling]	CAS: CAS, no CRC CAS_CRC: CAS with CRC CCS: CCS no CRC CCS_CRC: CCS with CRC CLEAR: Clear E1

Related Commands

addln, delln

Cards on which the command executes

FRSM, AUSM, CESM, IM-ATM

Attributes

Log: Yes State: Active Privilege: 1

Example 1 Description

cnfln 4 2 1 1

Configure line 4 to be T1 with B8ZS line coding, have a length of 1, and use the loop clock as a clock source.

System Response

No system response unless an error occurs.

cnfname

The cnfname command configures a name for the shelf. The name can be up to 20 characters. The name can consist of letters, numbers, and the special characters "_" and "-." It must begin with a letter and cannot contain spaces. The name is case sensitive.

Full Name

Configure shelf name

Syntax

cnfname <node name>

Related Commands

none

Cards on which the command executes

ASC

Attributes

Log: Yes State: Active Privilege: Superuser

Example 1 Description

cnfname Kanchendzonga

The prompt returns with the new name. However, on the command line the name is truncated because of the other information displayed in the prompt.

System Response

WIPRO_B.1.3.ASC.a > cnfname Kanchendzonga
11/14/95-07:03:57 3  StrataCom    0 cnfname Kanchendzonga
Kanchend.1.3.ASC.a >

cnfport

The cnfport command configures a service port on an FRSM or an AUSM.

The screen does not display a message after successful command entry. The configuration can be verified using the dspport command.

The syntax for this command is differs according to the service module being addressed.

Summary for FRSM

Full Name

Configure port

Syntax

cnfport <port_num> <lmi_sig> <asyn> <T391> <T392> <N391> <N392> <N393> <CLLMEN> <CLLMTM>

where:

<port_num>	port number is in the range of values 1-96
<lmi_sig>	LMI signalling: 1 = Other, 2 = None, 3 = StrataLMI, 4 = AnnexAUNI, 5 = AnnexDUNI, 6 = AnnexANNI, 7 = AnnexDNNI
<asyn>	asyn update is (y)es or (n)o
<T391>	T391 timer is in the range 5-30 sec.
<T392>	T392 timer is in the range 5-30 sec.
<N391>	N391 counter is in the range 1-255
<N392>	N392 counter is in the range 1-10
<N393>	N393 counter is in the range 1-10
<CLLMEN>	CLLM Enable is either 1 = Disable or 2 = Enable
<CLLMTM>	CLLM Timer is in the range 40-5000 ms

Possible errors are:

illegal/invalid parameters
port doesn't exist, use addport command to add port first
LMI NNI not enabled

Related Commands

addport, delport, dspport, dspports

Cards on which the command executes

FRSM

Attributes

Log: Yes State: Active Privilege: 1-6

Summary for AUSM

Full Name

Configure port

Syntax

cnfport <port_num> <plpp loopback>

where:

<port_num>	is in the range of values 1-4
<plpp loopback>	1 = no loopback, 2 = remote loopback, 3 = local loopback

Related Commands

addport, delport, dspport, dspports

Cards on which the command executes

AUSM

Attributes

Log: Yes State: Active Privilege: 1

cnfsrmclksrc

The cnfsrmclksrc command selects the clock source from either the BNM or a SRM-3T3 T3 line.

Full Name

Configure SRM clock source

Syntax

cnfsrmclksrc -synds3 <T3 line number> -synclk <Source number>

where:

<T3 Line number>	the SRM-3T3 T3 line number (range 1-3)
<Source number>	1: backplane clock for BMN, 2: recovery clock from T3 line

Related Commands

dspsrmclksrc

Cards on which the command executes

SRM-3T3

Attributes

Log: No State: Active Privilege: 1

cnfportq

The cnfportq command configures a port's queue parameters on the current AUSM. No messages appear on screen unless an error occurs.

Full Name

Configure port queue

Syntax

cnfportq <port_num> <q_num> <q_algo> <service_seq> <q_depth> <clp_high> <clp_low> <efci_thres>

where:

<port_num>	port_num is a port number in the range 1-4
<q_num>	queue 3 is the queue number in the range 1-16
<q_algo>	queue algorithm is the queue algorithm in the range 1-5, 0 = disable queue
<service_seq>	service sequence is the service sequence number in the range 1-16
<q_depth>	queue depth is the maximum queue depth in the range 1-8000 cells
<clp_high>	clp high is the high Cell Loss Priority in the range 1-8000 cells
<clp_low>	clp low is the low Cell Loss Priority in the range 1-8000 cells
<efci_thres>	efci threshold is the EFCI threshold in the range 1-8000 cells

Related Commands

none

Cards on which the command executes

AUSM

Attributes

Log: Yes State: Active Privilege: 1

copyports

The copyports command copies a port configuration to one or more ports. The purpose of this command is to create and configure multiple ports from a single port that serves as a template.

Full Name

Copy ports

Syntax

copyports <template port #> <start port #> <start time slot> <# of ports>

where:

<template port #>	template port number is the number of the port to be copied
<start port #>	start port number is the port to be copied
<start time slot>	start time slot is the starting time slot in the port to be copied
<# of ports>	number of ports is the number of contiguous time slots to be copied

Related Commands

delport, delports

Cards on which the command executes

FRSM, AUSM

Attributes

Log: No State: Active Privilege: 1

cnfpwd

The cnfpwd command configures a password. Prompts appear for the old and new passwords when the command is entered (without arguments).

Full Name

Configure password

Syntax

cnfpwd

then <old password>

then <new password>

then <new password again>

Related Commands

none

Cards on which the command executes

ASC

Attributes

Log: No State: Active Privilege: 1-6

Example 1 Description

cnfpwd

System Response

old password: 
new password: 
verify new password:

cnftime

The cnftime command configures the time. The shelf uses a 24-hour clock.

Full Name

Display time

Syntax

cnftime <hh:mm:ss>

Related Commands

none

Cards on which the command executes

ASC

Attributes

Log: Yes State: Active Privilege: Superuser

Example 1 Description

cnftime 14:22:03

System Response

kanchend.1.3.ASC.a > cnftime 14:11:22
11/14/95-14:11:22 3  tDbgCmdTask 1220 informational        : TIME/DATE updated        
11/14/95-14:11:22 3  StrataCom    0 cnftime 14:11:22

cnftmzn

The cnftmzn command configures the timezone in the shelf.

Full Name

Configure timezone

Syntax

cnftmzn <timezone>

where:

timezone is 1 for GMT, 2 for EST, 3 for CST, 4 for MST, 5 for PST

Related Commands

cnftime, cnfdate

Cards on which the command executes

ASC

Attributes

Log: Yes State: Active Privilege: Superuser

Example 1 Description

cnftmzn 3

Configures the timezone in the shelf to U.S. Central Standard Time.

The system responds by diplaying the entered timezone for confirmation.

cnftmzngmt

The cnftmzngmt command configures the timezone in the shelf relative to GMT.

Full Name

Configure timezone relative to GMT

Syntax

cnftmzngmt <timeoffsetGMT>

where:

timeoffsetGMT is the offset in hours from GMT. Permissible values are with the range -12 to 12.

Related Commands

cnftime, cnfdate

Cards on which the command executes

ASC

Attributes

Log: Yes State: Active Privilege: Superuser

Example 1 Description

cnftmzngmt 4

Sets time zone in the shelf to GMT plus 4 hours

cnftrapmgr

The cnftrapmgr command enables or disables the trap manager function. If enabled, this command configures the number and IP address of the trap manager that is to receive traps. Once the trap manager is configured, the system does not display the configuration. Only errors in the configuration appear on screen.

Full Name

Configure/delete/add trap manager

Syntax

cnftrapmgr <-ip> <ip_addr> -pt <portnum> <MgrRowStatus> -tf <TrapFlag> -seq <SeqNum>

where:

-ip ip_addr = nnn.nnn.nnn.nnn, n = 0-9, and nnn < 256
MgrRowStatus = 1-3, 1: AddRow 2: DelRow 3: ModRow
-tf <Trap Flag>
-seq <SeqNum>

Related Commands

dsptrapmgr

Cards on which the command executes

ASC

Attributes

Log: Yes State: Active Privilege: Superuser

Example 1 Description

cnftrapmgr -ip 192.169.3.102 -pt 3 MgrRowStatus 1 -tf 1 -seq 00

System Response

cnftrapmgr -ip 192.169.3.102 -pt 3 MgrRowStatus 1 -tf 1 -seq 00

cnfupcabr

The cnfupcabr command configures a connection's bandwidth control parameters for the available bit rate (ABR) connection type on the current AUSM. No messages appear on screen unless an error occurs.

Full Name

Configure user parameter control available bit rate

Syntax

cnfupcabr <chan_num> <enable> <pcr[0+1]> <cdvt[0+1]> <scr> <scr_police> <mbs> <clp_tag>

where:

<chan_num>	chan_num is a channel number in the range 16-271
<enable>	enable is the enabled/disable for UPC: 1 = Disable, 2 = Enable
<pcr[0+1]>	pcr[0+1] is the peak cell rate: the range is 10-4670 cells per sec.
<cdvt[0+1]>	cdvt[0+1] is the cell delay variation [0+1]: the range is 1-250000 micro secs
<scr>	scr is the sustained cell rate: the range is 1-4670 cells per second
<scr_police>	scr_police specifies the type of scr policing: 1 = CLP[0] Cells, 2 = CLP[0+1] Cells, and 3 = no SCR policing
<mbs>	mbs is the maximum burst size: the range is 1-5000 cells
<clp_tag>	clp_tag is the enable for CLP tagging: 1 = disable, 2 = enable

Related Commands

dspcon, dspcons, cnfupcabr, cnfupcvbr

Cards on which the command executes

AUSM

Attributes

Log: Yes State: Active Privilege: 1-2

cnfupccbr

The cnfupccbr command configures a connection's bandwidth control parameters for the constant bit rate (CBR) connection type on the current AUSM. No messages appear on screen unless an error occurs.

Full Name

Configure user parameter control constant bit rate

Syntax

cnfupccbr <chan_num> <enable/disable> <pcr[0+1]> <cdvt[0+1]> <pcr[0]> <cdvt[0]> <clp_tag>

where:

<chan_num>	chan_num is a channel number in the range 16-271.
<enable/disable>	enable/disable the UPC: 1 = disable, 2 = enable.
<pcr[0+1]>	PCR [0+1] is peak cell rate: the range is 10-4670.
<cdvt[0+1]>	CDVT[0+1] is Cell Delay Variation [0+1]: range is 1-250000 micro secs.
<pcr[0]>	PCR [0] is peak cell rate: the range is 10-4670.
<cdvt[0]>	CDVT[0] is Cell Delay Variation [0]: the range is 1-250000 microsecs.
<clp_tag>	clp_tag is Clp Tagging enable/disable: 1 = disable, 2 = enable.

Related Commands

dspcon, dspcons, cnfupcabr, cnfupcvbr

Cards on which the command executes

AUSM

Attributes

Log: Yes State: Active Privilege: 1-2

cnfupcvbr

The cnfupcvbr command configures a channel's bandwidth control parameters for a variable bit rate (VBR) connection type on the current AUSM. No messages appear on screen unless an error occurs.

Full Name

Configure user parameter control variable bit rate

Syntax

cnfupcvbr <chan_num> <enable> <pcr[0+1]> <cdvt[0+1]> <scr> <scr_police> <mbs> <clp_tag>

where:

<chan_num>	chan_num is a channel number in the range 16-271.
<enable>	enable is the enabled/disable for UPC: 1 = Disable, 2 = Enable.
<pcr[0+1]>	pcr[0+1] is the peak cell rate: the range is 10-4670 cells per sec.
<cdvt[0+1]>	cdvt[0+1] is the cell delay variation [0+1]: range is 1-250000 microsecs.
<scr>	scr is the sustained cell rate: the range is 1-4670 cells per second.
<scr_police>	scr_police specifies the type of scr policing: 1= CLP[0] Cells, 2 = CLP[0+1] Cells, and 3 = no SCR policing.
<mbs>	mbs is the maximum burst size: the range is 1-5000 cells.
<clp_tag>	clp_tag is the enable for CLP tagging: 1 = disable, 2 = enable.

Related Commands

dspcon, dspcons, cnfupcabr, cnfupccbr

Cards on which the command executes

AUSM

Attributes

Log: Yes State: Active Privilege: 1-2

copychans

The copychans command copies a channel configuration to one or more channels. The purpose of this command is to create and configure multiple channels from the channel that serves as a template.

Full Name

Copy channels

Syntax

copychans <template chan #> <start chan #> <start dlci> <# of chans>

where:

<template chan #>	template chan number
<start chan #>	start chan number
<start dlci>	start dlci for FRSM, start vci for AUSM
<# of chans>	number of chans

Related Commands

delchan, delchans

Cards on which the command executes

FRSM, AUSM

Attributes

Log: No State: Active Privilege: 1

delaimgrp

This command deletes an AIMUX group.

Full Name

Delete AIMUX group

Syntax

delaimgrp <aimux_grp>

where:

<aimux_grp>

is the AIMUX group number to be deleted (1..8)

Related Commands

addaimgrp, cnfaimgrps, dspaimgrp, dspaimgrps

Cards on which the command executes

IM-ATM

Attributes

Log: Yes State: Active Privilege: 1-2

dellnsfmaimgrp <aimux_grp> <list_of_lines>

where:

<aimux_grp>	is the AIMUX group from which lines should be deleted (1..8)
<list_of_lines>	is the list of lines to be deleted from the AIMUX group separated by dots

Example: dellnsfmaimgrp "2 3.5" (Deletes lines 3 and 5 from AIMUX group "2")

Related Commands

addlns2aimgrp

Cards on which the command executes

IM-ATM

Attributes

Log: Yes State: Active Privilege: 1-2

delchan

Deletes a frame relay channel from an FRSM.

No messages appear on screen after command entry unless the command cannot execute as entered.

Full Name

Delete channel

Syntax

delchan <channel number>

where:

channel number is in the range 16-271

Related Commands

dspchan, addchan, cnfchan

Cards on which the command executes

FRSM, AUSM, CESM

Attributes

Log: Yes State: Active Privilege: 1-2

delchanloop

Delete a channel loopback from the current FRSM or AUSM.

No messages appear on screen after command entry unless the command cannot execute as entered.

Full Name

Delete a channel loopback

Syntax

delchanloop <chan_num>

where:

<chan_num>

channel number is in the range 16-271

Related Commands

addchanloop, tstcon, tstdelay

Cards on which the command executes

FRSM, AUSM, CESM

Attributes

Log: Yes State: Active Privilege: 1-4

delchans

The delchans command deletes a range of frame relay or ATM channels.

Full Name

Delete channels

Syntax

delchans <start chan #> <# of chans>

where:

<start chan #>	start chan number
<# of chans>	number of chans

Related Commands

copychans, dspchans

Cards on which the command executes

FRSM, AUSM

Attributes

Log: No State: Active Privilege: 1

delcon

Deletes a connection from an AUSM.

No messages appear on screen after command entry unless the command cannot execute as entered.

Full Name

Delete a connection

Syntax

delcon <connection number>

where:

connection number is in the range 16-271

Related Commands

addcon, dspcons, dspcon

Cards on which the command executes

AUSM

Attributes

Log: Yes State: Active Privilege: 1-2

where:

<port_num>	numbers in the range 1 to 96 are valid
<line_num>	value ranging from 1 to 4
<ds0_speed>	1 for 56K, 2 for 64K
<begin_slot>	beginning timeslot number in the T1 or E1 frame
<num_slot>	number of consecutive timeslots in the T1 or E1 frame
<port_type>	is either 1, 2, or 3: 1 = frame relay, 2 = FUNI, 3=frame forwarding

dellink

The addlink command deletes a link between a T1 line within a T3 line on a SRM-3T3 card and a slot and line number on a T service module.

Full Name

Delete link

Syntax

dellink <T3 line number> <T1 line number> <Number of T1s>

where:

<T3 Line number>	the SRM-3T3 T3 line number (range 1-3)
<T1 line number>	the start T1 line number within the T3 line (range 1-28)
<Number of T1s>	the number of T1s to be deleted (range 1-28)

Related Commands

dsplink, addlink

Cards on which the command executes

SRM-3T3

Attributes

Log: No State: Active Privilege: 1

delln

The delln command deletes a line from the current card.

Full Name

Delete line

Syntax

delln <line number>

Related Commands

dspln, addln, cnfln

Cards on which the command executes

FRSM, AUSM, SRM-3T3, CESM, IM-ATM

Attributes

Log: Yes State: Active Privilege: 1

Example 1 Description

delln 4

Delete line 4 from the current card.

System Response

No system response unless an error occurs.

delport

The delport command deletes a port from an FRSM or AUSM.

No messages appear on screen with successful completion of this command.

Full Name

Delete port

Syntax

<aimux_grp>

is the AIMUX group number for the group to be displayed (1..8)

Related Commands

addaimgrp, delaimgrp, cnfaimgrps, dspaimgrps

Cards on which the command executes

IM-ATM

Attributes

Log: Yes State: Active Privilege: 1-2

dspaimgrpcnt

This command displays all the AIMUX related counters for a line in an AIMUX group.

Full Name

Display AIM group count

Syntax

dspaimgrpcnt <aimux_grp> <line_num>

where:

<aimux_grp>	is the AIMUX group number
<line_num>	is the line number

Related Commands

clraimgrpcnt

Cards on which the command executes

IM-ATM

Attributes

Log: Yes State: Active Privilege: 1-2

dspaimgrps

This command displays the parameters of all current AIMUX groups.

Full Name

Display AIM group

Syntax

dspaimgrps

Related Commands

addaimgrp, delaimgrp, cnfaimgrps, dspaimgrp

Cards on which the command executes

IM-ATM

Attributes

Log: Yes State: Active Privilege: 1-2

dspalm

The dspalm command displays the alarms for a line.

Full Name

Display alarms for a line

Syntax

dspalm <-ds3> | <-e3> |<plcp> | <-ds1> |<-srmds3> <LineNum>

for

-ds1, <LineNum> is in the range 1-4

-ds3, <LineNum> = 1

-e3, <LineNum> = 1

-plcp, <PLCPNum> = 1
-srmds3, <LineNum> is in the range 1-3

For an AXIS shelf with a BNM-155, the syntax is:

dspalm -sonet

Related Commands

clralm, dspalms

Cards on which the command executes

ASC, FRSM, AUSM, CESM, IM-ATM

Attributes

Log: No State: Active Privilege: 1-6

Example 1 Description

dspalm -plcp 1

On an ASC, display any alarm on the PLCP line.

System Response

PLCPNum:                   1
PLCPAlarmState:            No Alarm
PLCPStatisticalAlarmState: No Statistical Alarms

Example 2 Description

dspalm -sonet

On an ASC, display any alarm on the BNM-155 SONET line.

System Response

LineNum:
SectionCurrentStatus:
SectionStatAlarmStatus:
LineCurrentStatus:
LineStatAlarmStatus:
PathCurrentStatus:
PathStatAlarmStatus:

dspalmcnf

The dspalmcnf command displays the threshold information about the alarm statistics being collected.

Full Name

Display alarm configuration

Syntax

dspalmcnf <-ds3 LineNum> |<-e3 LineNum> | <-plcp PLCPNum> | <-ds1 LineNum> |<-srmds3 LineNum>

where:

On an ASC (BNM-T3), <LineNum> and <PLCPNum> = 1

On an FRSM, <LineNum> is in the range 1-4.

On an SRM-3T3, <LineNum> is in the range 1-3.

For an ASC and the shelf configured with a BNM-155, the syntax is:

dspalmcnf -sonetsec <SectionLineNum>|-sonetline<LineLineNum>|-sonetpath <PathLineNum>

Related Commands

dspalm, dspalms

Cards on which the command executes

ASC, FRSM, AUSM, SRM-3T3, CESM, IM-ATM

Attributes

Log: No State: Active Privilege: 1-6

Example 1 Description

dspalmcnf -ds1 1

Display the alarm configuration for line 4 on the current FRSM (slot 7 in this example).

System Response

         Severity   AlarmUpCount  AlarmDnCount  AlarmThreshold
  Line  Red / RAIS    NE / FE       NE / FE       NE  /  FE
  ---- ----- -----  ----- -----   ----- -----    ----- -----
  7.4  Major/Minor      6/1        1500/6            1/1500

Example 2 Description

dspalmcnf -ds3 1

Display the alarm configuration for the current ASC.

System Response

  LineNum:                  1
  RedSeverity:              Major
  RAISeverity:              Minor
  NEAlarmUpCount:           6
  NEAlarmDnCount:           1
  NEAlarmThreshold:         150
  FEAlarmUpCount:           6
  FEAlarmDnCount:           1
  FEAlarmThreshold:         150
  StatisticalAlarmSeverity: Minor
  LCV15minThreshold:        3870
  LCV24hrThreshold:         38650
  LES15minThreshold:        86
  LES24hrThreshold:         864     PSES24hrThreshold:        40
  LSES15minThreshold:       4       SEFS15minThreshold:       120
  LSES24hrThreshold:        40      SEFS24hrThreshold:        1200
  PCV15minThreshold:        382     AISS15minThreshold:       120
  PCV24hrThreshold:         3820    AISS24hrThreshold:        1200
  PES15minThreshold:        86      UAS15minThreshold:        120
  PES24hrThreshold:         864     UAS24hrThreshold:         1200
  PSES15minThreshold:       4

Example 3 Description

dspalmcnf -sonetsec 1

Display the alarm configuration for the current ASC for SONET section 1 on BNM-155.

System Response

SonetSectionLineNum:
SonetSectionStatAlarmSeverity:
SonetSectionCurrent15minESsThreshold:
SonetSectionCurrentDayESsThreshold:
SonetSectionCurrent15minSESsThreshold:
SonetSectionCurrentDaySESsThreshold:
SonetSectionCurrent15minSEFSsThreshold:
SonetSectionCurrentDaySEFSsThreshold:
SonetSectionCurrent15minCVsThreshold:
SonetSectionCurrentDayCVsThreshold:
SonetSectionTraceSel:
SonetSectionTraceToTx:
SonetSectionTraceToExpect:
SonetSectionTraceToRx:

dspalmcnt

The dspalmcnt command displays the alarm counters and statistics.

Full Name

Display alarm count

Syntax

dspalmcnt

Syntax ASC for BNM-T3:

: dspalmcnt "-ds3 <LineNum>"
: -ds3 <LineNum> where LineNum = 1-n, n = 1 if BNM
: or
: dspalmcnt "-e3 <LineNum>"
: -e3 <LineNum> where LineNum = 1-n, n = 1 if BNM
: or:
: dspalmcnt "-plcp <PLCPNum>"
: -plcp <PLCPNum> where PLCPNum = 1-n, n = 1 if BNM

Syntax ASC for BNM-155:

Syntax FRSM:

Related Commands

clralmcnt, clralmcnts

Cards on which the command executes

ASC, FRSM, AUSM, CESM, IM-ATM

Attributes

Log: No State: Active Privilege: 1-6

Example 1 Description

dspalmcnt -ds3 1

Display alarm count for line 1 of an ASC.

System Response

  LineNum:             1
  LCVCurrent:          0
  LCVLast15minBucket:  0
  LCVLast24hrBucket:   0
  LESCurrent:          0
  LESLast15minBucket:  0
  LESLast24hrBucket:   0
  LSESCurrent:         0
  LSESLast15minBucket: 0
  LSESLast24hrBucket:  0
  PCVCurrent:          0
  PCVLast15minBucket:  0
  PCVLast24hrBucket:   0
  PESCurrent:          0
  PESLast15minBucket:  0
  PESLast24hrBucket:   0
  PSESCurrent:         0
  PSESLast15minBucket: 0
  PSESLast24hrBucket:  0
  SEFSCurrent:         0
  SEFSLast15minBucket: 0
  SEFSLast24hrBucket:  0
  AISSCurrent:         0
  AISSLast15minBucket: 0
  AISSLast24hrBucket:  0
  UASCurrent:          0
  UASLast15minBucket:  0
  UASLast24hrBucket:   0
  PercentEFS:          100
  RcvLOSCount:         1
  RcvOOFCount:         1
  RcvRAICount:         4
  RcvCCVCount:         0
  RcvFECount:          0

Example 2 Description

dspalmcnt -ds1 1

Display alarms and counters for line 1 on the current FRSM

System Response

  Line  RcvLOSCount  RcvOOFCount  RcvRAICount  RcvFECount
  ----  -----------  -----------  -----------  ----------
  11.1            1            2           17           2

Example 3 Description

dspalmcnt -sonet 1

Display alarms and counters for line 1 on the BNM-155

System Response

SectionCurrentValidFlag:

SectionCurrent15minTimeElapsed:

SectionCurrentESs:

SectionCurrentSESs:

SectionCurrentSEFSs:

SectionCurrentCVs:

SectionCurrentDayValidFlag:

SectionCurrentDayESs:

SectionCurrentDaySESs:

SectionCurrentDaySEFSs:

SectionCurrentDayCVs:

SectionCounterLOSs:

SectionCounterLOFs:

LineCurrentValidFlag:

LineCurrent15minTimeElapsed:

LineCurrentESs:

LineCurrentSESs:

LineCurrentCVs:

LineCurrentUASs:

LineCurrentDayValidFlag:

LineCurrentDayESs:

LineCurrentDaySESs:

LineCurrentDayCVs:

LineCurrentDaySEFSs:

LineCounterAISs:

LineCounterRFIs:

PathCurrentValidFlag:

PathCurrent15minTimeElapsed:

PathCurrentESs:

PathCurrentSESs:

PathCurrentCVs:

PathCurrentFCs:

PathCurrentUASs:

PathCurrentDayValidFlag:

PathCurrentDayESs:

PathCurrentDaySESs:

PathCurrentDayCVs:

PathCurrentDayFCs:

PathCurrentDaySEFSs:

PathCounterAISs:

PathCounterRFIs:

dspalms

The dspalms command displays the alarms on the card.

Full Name

Display all alarms on a card

Syntax

dspalms -<lineType>

where:

-<lineType>

lineType can be ds3, plcp, ds1, or srmds3

For AXIS shelf configured with a BNM-155, the syntax is:

dspalms -sonet (the resulting display is the same as for the dspalm command)

Related Commands

dspalm

Cards on which the command executes

ASC, FRSM, AUSM, SRM-3T3, CESM, IM-ATM

Attributes

Log: No State: Active Privilege: 1-6

Example 1 Description

dspalms -ds1

Display alarms on the current FRSM (slot 7, in this case)

System Response

  Line  AlarmState   StatisticalAlarmState
  ----  -----------  ---------------------
  7.1   Alarm(s) On  No Statistical Alarms
  7.2   No Alarms    No Statistical Alarms
  7.3   No Alarms    No Statistical Alarms
  7.4   No Alarms    No Statistical Alarms

dspbert

The dspbert command displays the shelf for bit error rate testing.

Full Name

Display Bit Error Rate Test

Syntax

dspbert

where:

interface format is

Related Commands

cnfbert, modbert, delbert

Cards on which the command executes

ASC

A typical system response is shown below:

 User 	: StrataCom
 Start Date 	: 06/27/97
 Current Date 	: 06/27/97
 Start Time	: 02:43:08
 Current Time	: 02:43:21
Physical Slot Number 	: 6
Logical Slot Number 	: 6
Line Number 	: 1 (Line test)
Port Number	: 4 (Port test)
DS0 Speed	: 64K
Test Type	: BERT Pattern Test
 Device To Loop	: Latching CSU Device
BERT Pattern 	: Alternate One Zero Pattern
Error Inject Count	: 0
Iteration Count	: 0
Bit Count 	: 1148809
Bit Error Count	: 0
Bit Error Rate (BER)	: 0
BERT is in sync.

dspbnmif

The dspbnmif command displays the interface format for the BNM-155 trunk card.

Full Name

Display BNM Interface

Syntax

dspbnmif

Related Commands

cnfbnmif

Cards on which the command executes

ASC

The system responds by displaying the BNM line interface format.

dspbnmcnt

The dspbnmcnt command displays the cell counters on the BNM.

Full Name

Display BNM cell counter

Syntax

dspbnmcnt

Related Commands

clrbnmcnt

Cards on which the command executes

ASC

Attributes

Log: No State: Active Privilege: 1-6

Example 1 Description

dspbnmcnt

Port RcvCells XmtCells 1 17319744 33521472

System Response

  PortCounterNumOfValidEntries:  1
  CellbusXmtCellCount:           147842
  CellbusNoAckCellCount:         147812
  CellbusGrantCount:             158267
  EgressXmtCellCountDuringAlarm: 16
  EgressInvalidCellCount:        10424
  EgressInvalidCellHdr:          0
  IngressInvalidCellCount:       0
  IngressInvalidCellHdr          0

dspclksrc

The dspclksrc command displays the current clock source.

Full Name

Display current clock source

Syntax

dspclksrc

Related Commands

cnfclksrc

Cards on which the command executes

ASC, AUSM, IM-ATM

Attributes

Log: No State: Active Privilege: 1-6

Example 1 Description

dspclksrc

System Response

  PrimaryClockSource:   Internal Oscillator
  SecondaryClockSource: External T1/E1 from C.O.
  CurrentClockSource:   Internal Oscillator
  ClockSwitchState:     NoChange
  ExtClkPresent:        Not Present
  ExtClkSrcImpedance:   75 ohms
  ExtClkConnectorType:  BNC

dspcd

This command displays characteristics of the current card's hardware and firmware and information on its status. Card characteristics include serial number and hardware and firmware revision levels. Status may include the reason for the last reset (FunctionModuleRestReason) and state of the integrated alarm (cardIntegratedAlarm), which can be useful in debugging the card or the BPX, respectively. Some of the information is common to the version command display, but version shows boot code version in bold.

Full Name

Display card

Syntax

dspcd

Related Commands

cnfcd, dspcds, version

Cards on which the command executes

ASC, FRSM, AUSM, CESM, IM-ATM

Attributes

Log: No State: Any Privilege: 1-6

Example 1 Description

dspcd

On an AUSM:

System Response

  ModuleSlotNumber:          14
  FunctionModuleState:       Active
  FunctionModuleType:        AUSM-4T1
  FunctionModuleSerialNum:   FNTYPE
  FunctionModuleHWRev:       fk
  FunctionModuleFWRev:       model-A 2.0.00
  FunctionModuleResetReason: Reset by ASC from PIO
  LineModuleType:            LM-DB15-4T1
  LineModuleState:           Present
  mibVersionNumber:          4
  configChangeTypeBitMap:    CardCnfChng, LineCnfChng
  cardIntegratedAlarm:       Minor
  cardMinorAlarmBitMap:      Channel failure
axis3.1.14.AUSM.a >

Example 2 Description

dspcd

On an ASC:

System Response

  ModuleSlotNumber:          4
  FunctionModuleState:       Active
  FunctionModuleType:        ASC
  FunctionModuleSerialNum:   152698
  FunctionModuleHWRev:       p1
  FunctionModuleFWRev:       eqa2.0g
  FunctionModuleResetReason: WatchDog timeout reset
  LineModuleType:            LM-ASC
  LineModuleState:           Present
  mibVersionNumber:          0
  configChangeTypeBitMap:    No changes
  cardIntegratedAlarm:       Clear

Example 3 Description

dspcd

On an FRSM:

System Response

  ModuleSlotNumber:          7
  FunctionModuleState:       Active
  FunctionModuleType:        FRSM-4T1
  FunctionModuleSerialNum:   189142
  FunctionModuleHWRev:       aj
  FunctionModuleFWRev:       eqa2.0g
  FunctionModuleResetReason: Power reset
  LineModuleType:            LM-DB15-4T1
  LineModuleState:           Present
  mibVersionNumber:          4
  configChangeTypeBitMap:    CardCnfChng, LineCnfChng
  cardIntegratedAlarm:       Clear

dspcderrs

The dspcderrs command displays information on the card errors.

Full Name

display card errors

Syntax

dspcderrs

Related Commands

clrcderrs

Cards on which the command executes

ASC, FRSM, AUSM, IM-ATM

Attributes

Log: No State: Any Privilege: 1-6

Example 1 Description

dspcderrs

Note that, if no errors have occurred, no messages appear on screen.

System Response

dspcderrs
08/05/95-18:53:05 tRootTask    3 Task failed          : scm                     
09/05/95-09:14:08 tRootTask    3 Task failed          : scm                     
value = 0 = 0x0

dspcds

The dspcds command displays the status of all the cards in the AXIS shelf.

Full Name

Display card shelf information

Syntax

dspcds

Related Commands

dspcd

Cards on which the command executes

ASC, SRM-3T3

Attributes

Log: No State: Any Privilege: 1-6

Example 1 Description

dspcds

Executed from an ASC:

System Response

 Slot  CardState    CardType  CardAlarmStatus
 ----  -----------  --------  ---------------
  1.1   Standby      BNM-T3
  1.2   Active       BNM-T3
  1.3   Standby      ASC
  1.4   Active       ASC
  1.5   Active       FRSM-4T1    Major
  1.6   Active       FRSM-4T1
  1.7   Active       FRSM-4T1
  1.8   Active       FRSM-4T1
  1.9   Empty
  1.10  Active       FRSM-4T1
  1.11  Active       FRSM-4T1
  1.12  Active       FRSM-4T1
  1.13  Active       FRSM-4T1
  1.14  Active       FRSM-4T1
  1.15  Standby      SRM-4T1/E1
  1.16  Active       SRM-4T1/E1
BkplnSerialNum:
  NumOfValidEntries:    16
  NodeName:             AXISNAME
  Date:                 11/22/95
  Time:                 07:40:03
  TimeZone:             PST
  TimeZoneGMTOff:       -8
  StatsMasterIpAddress: 0.0.0.0
  ShelfIntegratedAlarm: Major
Syntax : dspcds

dspchan

Displays a frame relay channel on an FRSM.

Full Name

Display channel

Syntax

dspchan <channel number>

where:

channel number is in the range 16-271

Related Commands

dspchans, cnfchan

Cards on which the command executes

FRSM, AUSM, CESM

Attributes

Log: No State: Any Privilege: 1-6

Example 1 Description

dspchan 69

Display the channel characteristics of channel 69.

System Response

  ChanNum:                  69
  ChanRowStatus:            Mod
  ChanPortNum:              1
  ChanDLCI:                 100
  EgressQSelect:            1
  IngressQDepth:            65535
  IngressQDEThresh:         32768
  IngressQECNThresh:        65535
  EgressQDepth:             65535
  EgressQDEThresh:          32768
  EgressQECNThresh:         6553
  DETaggingEnable:          Disabled
  CIR:                      24000
  Bc:                       5100
  Be:                       5100
  IBS:                      100
  ForeSightEnable:          Enabled
  QIR:                      260
  MIR:                      62
  PIR:                      500
  ChanLocalRemoteLpbkState: Enabled
  ChanTestType:             TestOff
  ChanTestState:            NotInProgress
  ChanRTDresult:            65535 ms
  ChanType:                 NIW
  ChanFECNmap:              setEFCIzero
  ChanDEtoCLPmap:           mapCLP
  ChanCLPtoDEmap:           mapDE
  ChanNumNextAvailable:  17

For an AUSM, the display is the same as for the dspcon display.

dspchancnt

Displays the counter contents of a channel.

Full Name

Display channel count

Syntax

dspchancnt <channel number>

where:

channel number is in the range 16-271

Related Commands

dspchstats

Cards on which the command executes

FRSM, AUSM, CESM, IM-ATM

Attributes

Log: No State: Any Privilege: 1-6

Example 1 Description

dspchancnt 69

Display the counters for channel 69 of the current FRSM

System Response

ChanNum:          69
ChanState:        okay
ChanUpTime:       10186
                                  Tx                            Rx
                             ---------------            ---------------
  AbitState:                 Sending A=1                Receiving A=1
  ATMState:                  Not sending any state      Not receiving any state
  Total Frames:              0                          0
  Total Bytes:               0                          0
  Frames DE:                 0                          0
  Bytes DE:                  0                          0
  Frames Discarded:          0                          0
  Bytes Discarded:           0                          0
  FramesDiscXceedQDepth:     0                          0
  BytesDiscXceedQDepth:      0                          0
  FramesDiscXceedDEThresh:   0                          0
  Frames FECN:               0                          0
  Frames BECN:               0                          0
  FramesTagged FECN:         0                          0
  FramesTagged BECN:         0                          0
  KbpsAIR:                   0                          0
  FramesTaggedDE:            0                          0
  BytesTaggedDE:             0                          0
  RcvFramesDiscShelfAlarm:                              0
  XmtFramesDiscPhyLayerFail: 0
  XmtFramesDiscCRCError:     0
  XmtFramesDiscReAssmFail:   0
  XmtFramesDiscSrcAbort:     0
  XmtFramesDuringLMIAlarm:   0
  XmtBytesDuringLMIAlarm:    0
  RcvFramesDiscUPC:                                     0
  XmtFramesInvalidCPIs:      0
  XmtFramesLengthViolations: 0
  XmtFramesOversizedSDUs:    0
  XmtFramesUnknownProtocols: 0
  RcvFramesUnknownProtocols:                            0

Example 2 Description

dspchancnt 16

Display the counters for channel 16 of the current AUSM

System Response

  ChanNum:                         16
  ChannelState:                    Active
  ChannelEgressRcvState:           Normal
  ChannelEgressXmitState:          Normal
  ChannelIngressRcvState:          Normal
  ChannelIngressXmtState:          Normal
  ChanInServiceSeconds:            1126725
  ChanIngressPeakQDepth(cells):    1
  ChanIngressReceiveCells:         41160574
  ChanIngressClpSetCells:          0
  ChanIngressEfciSetRcvCells:      0
  ChanIngressUpcClpSetCells:       0
  ChanIngressQfullDiscardCells:    1
  ChanIngressClpSetDiscardCells:   0
  ChanIngressTransmitCells:        41160574
  ChanShelfAlarmDiscardCells:      0
Syntax : dspchancnt "chan_num"
         channel number -- value ranging from 16 to 271

dspchans

This command displays all the frame relay channels on the card.

Full Name

Display channels

Syntax

dspchans

Related Commands

dspchan, addchan, delchan

Cards on which the command executes

FRSM, AUSM, CESM

Attributes

Log: No State: Any Privilege: 1-6

Example 1 Description

dspchans

Display the channels on the current FRSM.

System Response

    DLCI       Chan  EQ  I/EQDepth  I/EQDEThre  I/EECNThre  Fst/DE  Type  Alarm
  ------------- ---- -- ----- ----- ----- ----- ----- ----- --- --- ----- -----
  11.1.1.100    69   1  65535/65535 32768/32768 65535/6553  Ena/Dis NIW    No
  11.1.1.101    70   1  65535/65535 32768/32768 65535/6553  Ena/Dis NIW    No
  11.1.1.102    71   1  65535/65535 32768/32768 65535/6553  Ena/Dis NIW    No
  11.1.1.103    72   1  65535/65535 32768/32768 65535/6553  Ena/Dis NIW    No
  11.1.1.104    73   1  65535/65535 32768/32768 65535/6553  Ena/Dis NIW    No
  11.1.1.105    74   1  65535/65535 32768/32768 65535/6553  Ena/Dis NIW    No
  11.1.1.106    75   1  65535/65535 32768/32768 65535/6553  Ena/Dis NIW    No
  11.1.1.107    76   1  65535/65535 32768/32768 65535/6553  Ena/Dis NIW    No
  11.1.1.108    77   1  65535/65535 32768/32768 65535/6553  Ena/Dis NIW    No
  11.1.1.109    78   1  65535/65535 32768/32768 65535/6553  Ena/Dis NIW    No
  11.1.1.110    79   1  65535/65535 32768/32768 65535/6553  Ena/Dis NIW    No
  11.1.1.111    80   1  65535/65535 32768/32768 65535/6553  Ena/Dis NIW    No
  11.1.1.112    81   1  65535/65535 32768/32768 65535/6553  Ena/Dis NIW    No
  11.1.1.113    82   1  65535/65535 32768/32768 65535/6553  Ena/Dis NIW    No
  11.1.1.114    83   1  65535/65535 32768/32768 65535/6553  Ena/Dis NIW    No
  11.1.1.115    84   1  65535/65535 32768/32768 65535/6553  Ena/Dis NIW    No
  11.1.2.100    85   1  65535/65535 32768/32768 65535/6553  Ena/Dis NIW    No
Type <CR> to continue, Q<CR> to stop:

For an AUSM, the display is the same as for the dspcon display.

dspchstats

Displays the current statistics of a channel.

Full Name

Display channel statistics

Syntax

dspchstats <line#><1st_DS0><DLCI>

where:

<line#>	line number is in the range 1-4
<1st_DS0>	1st_DS0 is in the range of 1-24 for T1, 1-32 for E1
<DLCI>	DLCI is the connection for which the statistics are to be displayed

Related Commands

dspchstats

Cards on which the command executes

FRSM

Attributes

Log: No State: Any Privilege: 1-6

Example 1 Description

dspchstats 2.4.1000

Display the counters for line 1, 1st_DS0 of 4, and DLCI or 1000 for the current FRSM

System Response

                          lineNum:           1
                          Physical Port Num: 4
                          Logical Port Num:  2
                          ChanDLCI:          1000
                          ChanNum:           1
                          ChanState:        okay
                          ChanUpTime:       10186
                                  Tx                            Rx
                             ---------------            ---------------
  AbitState:                 Sending A=1                Receiving A=1
  ATMState:                  Not sending any state      Not receiving any state
  Total Frames:              0                          0
  Total Bytes:               0                          0
  Frames DE:                 0                          0
  Bytes DE:                  0                          0
  Frames Discarded:          0                          0
  Bytes Discarded:           0                          0
  FramesDiscXceedQDepth:     0                          0
  BytesDiscXceedQDepth:      0                          0
  FramesDiscXceedDEThresh:   0                          0
  Frames FECN:               0                          0
  Frames BECN:               0                          0
  FramesTagged FECN:         0                          0
  FramesTagged BECN:         0                          0
  KbpsAIR:                   0                          0
  FramesTaggedDE:            0                          0
  BytesTaggedDE:             0                          0
  RcvFramesDiscShelfAlarm:                              0
  XmtFramesDiscPhyLayerFail: 0
  XmtFramesDiscCRCError:     0
  XmtFramesDiscReAssmFail:   0
  XmtFramesDiscSrcAbort:     0
  XmtFramesDuringLMIAlarm:   0
  XmtBytesDuringLMIAlarm:    0
  RcvFramesDiscUPC:                                     0
  XmtFramesInvalidCPIs:      0
  XmtFramesLengthViolations: 0
  XmtFramesOversizedSDUs:    0
  XmtFramesUnknownProtocols: 0
  RcvFramesUnknownProtocols:                            0

dspcon

Displays configuration data for a connection.

Full Name

Display connection

Syntax

dspcon <channel number>

where:

channel number is in the range 16-271

Related Commands

addcon, delcon, dspcons

Cards on which the command executes

AUSM

Attributes

Log: No State: Any Privilege: 1-6

Example 1 Description

dspcon 16

Display the connection parameters for channel 16.

System Response

  ChanNum:                                  16
  RowStatus:                                Add
  ConnectionType:                           VCC
  ServiceType:                              CBR
  PortNum:                                  1
  VPI:                                      10
  VCI:                                      100
  EgressQNum:                               1
  IngressQDepth (cells):                    100
  IngressQCLPHigh (cells):                  70
  IngressQCLPLow (cells):                   60
  IngressEfciThreshold (cells):             50
  CompliantCellDelayVariation (micro secs): 0
  CompliantInfoRate (cells/sec):            0
  InitialBurstSize (cells):                 0
  MaxFrameSize (cells):                     0
  PeakInformationRate (cells/sec)           1000
  CLPTagEnable:                             Disabled
  FrameGCRAEnable:                          Disabled

dspcons

Displays details of all connections between the current AUSM and the BNI to which the current shelf attaches.

Full Name

Display connections

Syntax

dspcons

Related Commands

dspcon, addcon, delcon

Cards on which the command executes

AUSM

Attributes

Log: No State: Any Privilege: 1-6

Example 1 Description

dspcons

Display parameters for the connections on the current AUSM.

System Response

Chan    Port.VPI.VCI    ConnType    Service Type    PCRlot1   Q-Depth     State
30        1.10.100       VCC            ABR          3622      2000       Active
33        1.10.200       VPC            CBR          3622      100        Alarm

dspifip

The dspifip command displays the interface addresses configured for the card. These addresses can be Ethernet, Slip, and ATM.

Full Name

Display LAN IP configuration

Syntax

dspifip

Related Commands

cnfifip

Cards on which the command executes

ASC

Attributes

Log: No State: Any Privilege: 1-6

Example 1 Description

dspifip

Display the IP LAN configuration.

System Response

  IPAddress   Interface      NetMask      BroadcastAddress
 -----------  ---------  ---------------  ----------------
192.168.3.18  Ethernet   255.255.255.000  192.168.3.18   
     0.0.0.0  Slip       255.255.255.000       N/A       
     0.0.0.0  ATM        255.255.255.000       N/A

dspilmi

The dspilmi command displays the interim local management interface (ILMI) configuration.

Full Name

display ilmi

Syntax

dspilmi <port_num>

where:

<port_num>

port_num is in the range 1-4

Related Commands

cnfilmi. dspilmicnt

Cards on which the command executes

AUSM

Attributes

Log: No State: Any Privilege: 1-6

Example 1 Description

dspilmi 1

Display the ILMI configuration for port 1.

System Response

  Port Num:                      1
  Signalling:                    No signalling
  SignallingVPI:                 0
  SignallingVCI:                 0
  ILMITrap:                      Disabled
  ILMI-Min-Trap-Interval (secs): 1
  KeepAlivePolling:              Disabled
  ErrorThreshold:                3
  EventThreshold:                4
  PollingInterval (secs):        30
  MinmumEnquiryInterval (secs):  10
  EXT Operation:                 port 2

dspilmicnt

The dspilmicnt command displays the ILMI counters.

Full Name

display ilmi counters

Syntax

dspilmicnt <port_num>

where:

<port_num>

port_num is in the range 1-4

Related Commands

cnfilmi, dspilmi

Cards on which the command executes

AUSM

Attributes

Log: No State: Any Privilege: 1-6

Example 1 Description

dspilmicnt 1

Display the ilmi counters for port 1 on the current AUSM card.

System Response

  Port Num:                 1
  SNMPPDUsReceived:         0
  Get RequestsReceived:     0
  GetNextRequestsReceived:  0
  SetRequestsReceived:      0
  TrapReceived:             0
  GetResponseReceived       0
  GetResponseTransmitted:   0
  GetRequestTransmitted:    0
  TrapsTransmitted:         0
  InvalidPDUReceived:       0
  Asn1ParseError:           0
  NoSuchNameError:          0
  TooBigError:              0

dspintvl

The dspintvl command displays interval statistics for BNM-155 trunk card.

Full Name

Display interval

Syntax

dspintvl -sonetsec <sonetsecLineNumber> -intvl <intervalNum>|-sonetline <sonetLineLineNumber> -intvl<intervalNum>|sonetPathLineNum <sonetPathLineNumber> -intvl <intervalNum>

Related Commands

Cards on which the command executes

SRM-3T3 on shelf equipped with BNM-155

Attributes

Log: No State: Active Privilege: 1

Example

System Response

SonetSectionLineNum:
SectionIntervalNum:
SectionCurrentValidFlag:
SectionCurrentESs:
SectionCurrentSESs:
SectionCurrentSEFSs:
SectionCurrentCVs:

dsplink

The dsplink command displays a link on a T3 line on a SRM-3T3 card.

Full Name

Display link

Syntax

dsplink <T3 line number>

where:

the SRM-3T3 T3 line number (range 1-3)

Related Commands

dellink, addlink

Cards on which the command executes

SRM-3T3

Attributes

Log: No State: Active Privilege: 1

System Response

T3Line	StartT	TRowStatus	TargetSlot	TargetSlotLine
1	1	Add	7	1
1	2	Add	7	2
1	3	Add	7	3
1	4	Add	7	4

dspln

The dspln command displays the detailed configuration for the specified line. If the current card is an ASC, the line is a ds3 if the shelf is configured with a BNM-T3 trunk card and SONET if the shelf is configured with a BNM-155 trunk card.

Full Name

Display line

Syntax

On FRSM or AUSM cards

dspln <line number>

where:

line number can be 1 on an ASC and 1-4 on an FRSM or AUSM

On SRM-3T3 cards

dspln <-srmds3><line number>

where:

line number can be 1-3

Related Commands

addln, cnfln, delln

Cards on which the command executes

ASC, FRSM, AUSM, SRM-3T3, CESM, IM-ATM

Attributes

Log: No State: Active on ASC, any state on FRSM, AUSM, or SRM-3T3 Privilege: 1-6

Example 1 Description

dspln 2

Display line 2 on the current AUSM card.

System Response

 LineNum:                 2
 LineConnectorType:       BNC
 LineType:                dsx1E1CAS
 LineEnable:              Enabled
 LineCoding:              dsx1HDB3
 LineLength:              G.703 75 ohm
 LineXmtClockSource:      LocalTiming
 LineLoopbackCommand:     NoLoop
 LineSendCode:            NoCode
 LineUsedTimeslotsBitMap: 0xffffffff
 ConfigChangePortBitMap:  0x0
  LineNumOfValidEntries: 4

Example 2 Description

dspln 1

Display line 1 on the current ASC (1 is the only valid line number on an ASC).

System Response for BNM-T3

  LineNum:               1
  LineType:              dsx3CbitParity
  LineCoding:            dsx3B3ZS
  LineLength:            LessThan450ft
  LineOOFCriteria:       3 out of 8
  LineAIScBitsCheck:     Check C-bits
  LineLoopbackCommand:   NoLoop
  LineRcvFEACValidation: 4 out of 5 FEAC codes
  
  LineNumOfValidEntries: 1

System Response for BNM-155

sonetLineNum:               1
sonetLineType: 
sonetLineloopbak: 
sonetHCmasking: 
sonetPayloadScramble: 
sonetFrameScramble: 
sonetMediumType: 
sonetMediumTimeElapsed: 
sonetMediumValidIntervals
sonetMediumLineCoding
sonetMediumLineType
sonetMediumCircuitIdentifier
sonetMediumValidEntries:

dsplns

The dsplns command displays the configuration for all lines on the current card. The displayed parameters depend on the card.

Full Name

Display lines

Syntax

dsplns

Related Commands

addln, cnfln, delln

Cards on which the command executes

ASC, FRSM, AUSM, CESM, IM-ATM

Attributes

Log: No State: Active on ASC, any state on FRSM, or AUSM Privilege: 1-6

Example 1 Description

dsplns

Display lines on the current FRSM card.

System Response

 Line  ConnType     Type      Enable/Coding      Length     XmtClockSource
 ----  -------- ------------ ------- -------- ------------- --------------
  7.1   DB-15    dsx1ESF      Modify/dsx1B8ZS   0-110 ft     LocalTiming
  7.2   DB-15    dsx1ESF      Modify/dsx1B8ZS   0-110 ft     LocalTiming
  7.3   DB-15    dsx1ESF      Modify/dsx1B8ZS   0-110 ft     LocalTiming
  7.4   DB-15    dsx1ESF      Modify/dsx1B8ZS   0-110 ft     LocalTiming
  LineNumOfValidEntries: 4

System Response

Line  ConnType     Type      Enable/Coding      Length     XmtClockSource
----  -------- ------------ ------- -------- ------------- --------------
 7.1   DB-15    dsx1ESF      Modify/dsx1B8ZS   0-110 ft      LocalTiming
 7.2   DB-15    dsx1ESF      Modify/dsx1B8ZS   0-110 ft      LocalTiming
 7.3   DB-15    dsx1ESF      Modify/dsx1B8ZS   0-110 ft      LocalTiming
 7.4   DB-15    dsx1ESF      Modify/dsx1B8ZS   0-110 ft      LocalTiming
  LineNumOfValidEntries: 4

Example 2 Description

dsplns

Display lines on the current ASC with BNM-T3 trunk card.

System Response

Line       Type        Coding      Length       Criteria   AIScBitsCheck
----  --------------  --------  -------------  ----------- -------------
2.1   dsx3CbitParity  dsx3B3ZS  LessThan450ft  3 out of 8  Check C-bits
LineNumOfValidEntries: 1

Example 3 Description

dsplns

Display lines on the current ASC with BNM-155 trunk card.

System Response

Medium Medium Medium Medium Sonet Line Line HSC Payload Frame Time Valid Line Line Line Type Lpbk mask Scramble Scramble Elapsed Intvls Coding Type ---- -------------- -------- ------------- ----------- ------------------ LineNumOfValidEntries: 1

dspsrmlns

The dsplns command display the configuration for all lines on the current card. The displayed parameters depend on the card (see example).

Full Name

Display lines

Syntax

dspsrmlns

Related Commands

addln, cnfln, delln

Cards on which the command executes

SRM-3T3

Attributes

Log: No State: Active on SRM-3T3 Privilege: 1-6

Example 1 Description

dsplns

Display lines on the current SRM 3T3 card.

System Response

Line  Enable       Type        Coding      Criteria   AIScBitsCheck  FELpbkStatus
---- -------- ------------     -------     --------   ------------- --------------
1.1  Disable  dsx3CbitParity   dsx1B3ZS   3 out of 8  Check C-bits  No far end 
1.1  Disable  dsx3CbitParity   dsx1B3ZS   3 out of 8  Check C-bits  No far end 1
1.1  Disable  dsx3CbitParity   dsx1B3ZS   3 out of 8  Check C-bits  No far end 
  LineNumOfValidEntries: 3

dsploads

The dsploads command displays the connection load at a port. This helps to determine whether adding more connections is advisable. The display shows the load in cells per second. The layout of the display is in rows and columns. One column exists for each port, and one row exists for each connection type. If the traffic is exceeding the bandwidth configured for the port, an "overload" message appears at the bottom of the column for the overloaded port.

Full Name

Display loads

Syntax

dsploads

Related Commands

none

Cards on which the command executes

AUSM

Attributes

Log: No State: Active Privilege: 1-6

Example 1 Description

dspmsgcnt

Display the load on the current AUSM.

System Response

Load Display for AUSM ports

                        Port 1  Port2   Port3   Port4
                        *******************************
CBR (based on PCR0+1)       0       0       0       0
VBR (based on PCR0+1)       0       0       0       0
ABR (based on MCR)      64000   64000   64000   64000
                        -------------------------------
Total                   64000   64000   64000   64000
Load Status             OverloadOverloadOverloadOverload
Note: All Cell Rates are multiplied by respective
                Percentage Utilization factors

dsplog

The dsplog command displays the events and messages in the log. The most recent events appear at the top of the list.

Full Name

Display event/message log

This command displays the AXIS log. If no parameters are entered, the entire log for all cards in the shelf is displayed. The log for a particular card and/or for only a number of most recent days can be specified.

Syntax

dsplog [<slot#>] [<no. of days>]

where:

<slot#>	is the slot number of the card for which the log is to be displayed
<no. of days>	is the number of most recent days to be included in the display (up to 4 maximum)

Related Commands

clrlog

Cards on which the command executes

ASC, FRSM

Attributes

Log: No State: Active Privilege: 1-5

Example 1 Description

dsplog

System Response

dsplog
04/01/70-13:10:03 tRootTask    2 Illegal msg received
04/01/70-13:10:07 aum        1312 local IP address not programmed
03/01/70-20:11:31 smm        1207 slave ack timeout

dspmaptbl

The dspmaptbl command displays the numbers assigned to frame relay ports or ATM ports on the FRSM or AUSM, respectively.

Full Name

Display map table

Syntax

dspmaptbl

Related Commands

Cards on which the command executes

FRSM, AUSM

Attributes

Log: No State: Active Privilege: 1-6

Example 1 Description

dspmaptbl

Display the map table for the current FRSM.

System Response

PortNum  DLCI  ChanNum  LineNum
  -------  ----  -------  -------
   1       100    69        1
   1       101    70        1
   1       102    71        1
   1       103    72        1
   1       104    73        1
   1       105    74        1
   1       106    75        1
   1       107    76        1
   1       108    77        1
   1       109    78        1
   1       110    79        1
   1       111    80        1
   1       112    81        1
   1       113    82        1
   1       114    83        1
   1       115    84        1
   2       100    85        1
   2       101    86        1
   2       102    87        1
   2       103    88        1
Type <CR> to continue, Q<CR> to stop:

Example 2 Description

dspmaptbl

Display the map table for the current AUSM.

System Response

 PortNum  VPI  VCI ChanNum  Channel Type
  -------  ---  --- -------  ------------
   1       1    16   16        VCC
   1       1    17   17        VCC
   1       1    18   18        VCC
   1       1    19   19        VCC
   1       1    20   20        VCC
   1       1    21   21        VCC
   1       1    22   22        VCC
   1       1    23   23        VCC
   1       1    24   24        VCC
   1       1    25   25        VCC
   1       1    26   26        VCC
   1       1    27   27        VCC
   1       1    28   28        VCC
   1       1    29   29        VCC
   1       1    30   30        VCC
   1       1    31   31        VCC
   1       1    32   32        VCC
   1       1    33   33        VCC
   1       1    34   34        VCC
   1       1    35   35        VCC
Type <CR> to continue, Q<CR> to stop:

dspmsgcnt

The dspmsgcnt command displays the control message counter for the card.

Full Name

Display control message counter

Syntax

dspmsgcnt

Related Commands

clrmsgcnt

Cards on which the command executes

ASC, FRSM, AUSM, CESM, IM-ATM

Attributes

Log: No State: Active Privilege: 1-6

Example 1 Description

dspmsgcnt

System Response

  RiscXmtCtrlMsg:            88506
  RiscRcvCtrlMsg:            53494
  SARXmtCtrlMsg:             88506
  SARRcvCtrlMsg:             53494
  SARCtrlMsgDiscLenErr:      0
  SARCtrlMsgDiscCRCErr:      0
  SARCtrlMsgDiscUnknownChan: 0
  SARCtrlMsgLastUnknownChan: 0

dspport

On an FRSM, the dspport command displays the frame relay port configuration for the specified port. On an AUSM, the dspport command displays the Physical Layer Protocol Processor of a port on the current AUSM.

Full Name

Display port

Syntax

dspport <port number>

where:

On an FRSM, port number is the port number in the range 1-96

On an AUSM, port number is the port number in the range 1-4

Related Commands

FRSM: addport, cnfport, delport

AUSM: upport, dnport

Cards on which the command executes

FRSM, AUSM

Attributes

Log: No State: Active Privilege: 1-6

Example 1 Description

dspport 1

Display the port configuration for port 1 on the current FRSM.

System Response

  SlotNum:                      7
  PortLineNum:                  1
  PortNum:                      1
  PortRowStatus:                Add
  PortDs0Speed:                 64k
  PortDs0ConfigBitMap:          0xffffff
  PortEqueueServiceRatio:       1
  PortFlagsBetweenFrames:       1
  PortSpeed:                    1536kbps
  SignallingProtocolType:       NoSignalling
  AsynchronousUpdates:          Disable
  T391LineIntegrityTimer:       10
  T392PollingVerificationTimer: 15
  N391FullStatusPollingCounter: 6
  N392ErrorThreshold:           3
  N393MonitoredEventCount:      4
  PortState:                    FailedDuetoLineFailure
  PortSignallingState:          No Signalling Failure
  CLLMEnableStatus:             Disable
  CLLMxmtStatusTimer:           0
  PortDs0UsedLine1:             0x00ffffff
  PortDs0UsedLine2:             0x00ffffff
  PortDs0UsedLine3:             0x00ffffff
  PortDs0UsedLine4:             0x00ffffff
  PortNumNextAvailable:         60
Syntax : dspport "port_num"
         port number -- values ranging from 1-96 are accepted

dspport 1

Display port 1 on the current AUSM.

  PortNumber:     1
  Cell Framing:   ATM
  Cell Scramble:  No Scramble
  Plpp Loopback:  No Loopback

dspportcnt

This command displays counters for a specified port.

Full Name

Display port counters

Syntax

dspportcnt <port number>

where:

port number is in the range 1-96

Related Commands

cnfcd, dspcds

Cards on which the command executes

FRSM, AUSM

Attributes

Log: No State: Any Privilege: 1-6

Example 1 Description

dspportcnt 1

Display port counters on port 1 of the current AUSM.

System Response

 PortNum:                               1
 PortState:                             Out Of Cell Delineation
 IngressRcvCells:                       0
 IngressGfcErrorCells:                  0
 IngressVpiVciErrCells:                 0
 IngressUnknownVpiVci:                  0
 EgressXmtCells:                        918900
 EgressPortAlarmDiscardCells:           0
 EgressXmtClpSetCells:                  918907
 EgressXmtEfciSetCells:                 0
 PortXmtAisCells:                       918907
 PortXmtSgmtLpbkCells:                  0
 PortRcvAisCells:                       0
 PortRcvFerfCells:                      0
 PortRcvSgmtLpbkCells:                  0
 PortRcvCrcErrOAMCells:                 0
 ReceivedHECErrorCells:                 6
 HECErroredSeconds:                     1
 SeverelyHECErroredSeconds:             0

Example 2 Description

dspportcnt 1

On an FRSM:

System Response

                                      Tx                 Rx
                               ---------------    ---------------
  Total Frames:                0                  0
  Total Bytes:                 0                  0
  Frames FECN:                 0                  0
  Frames BECN:                 0                  0
  Frames Abort:                0                  0
  Buf Not Available:           0                  0
  KbpsAIR:                     0                  0
  XmtFramesDiscXceedQDepth:    0
  XmtBytesDiscXceedQDepth:     0
  XmtFramesDuringLMIAlarm:     0
  XmtByteDuringLMIAlarm:       0
  XmtFramesUnderrun:           0
  RcvFramesDE:                                    0
  RcvFramesDiscCRCError:                          0
  RcvFramesDiscIllegalHeader:                     0
  RcvFramesDiscAlignmentError:                    0
  RcvFramesDiscIllegalLen:                        0
  RcvFramesDiscXceedDEThresh:                     0
  RcvFramesUnknownDLCI:                           0
  RcvLastUnknownDLCI:                             0
  RcvFramesTaggedFECN:                            0
  RcvFramesTaggedBECN:                            0
  RcvFramesTaggedDE:                              0
  Status:                      0                  0
  StatusInquiry:               0                  0
  AsynchUpdate:                0                  0
  RcvInvalidRequest:                              0
  RcvUNISeqMismatch:                              0
  RcvNNISeqMismatch:                              0
  UNISignallingTimeout:                           0
  NNISignallingTimeout:                           0
  FramesCLLM:                  0                  0
  BytesCLLM:                   0                  0
  CLLMFailures:                               		    0

dspportstats

The dspportstats command displays statistics information for a specified port on the FRSM.

Full Name

display port statistics

Syntax

dspportstats <line#><1st_DS0>

where:

<line#>	line number is in the range 1-4
<1st_DS0>	1st_DS0 is in the range 1-24, for T1, and 1-32 for E1

Related Commands

dspchstats

Cards on which the command executes

FRSM

Attributes

Log: No State: Any Privilege: 1-6

Example 1 Description

dspportstats 1 12

Display statistics information for port 1 on first DS0 of 12.

System Response

Line Num:1
Physical Port Num: 12
Logical Port Num: 4
                                    Tx                 Rx
                               ---------------    ---------------
  Total Frames:                0                  0
  Total Bytes:                 0                  0
  Frames FECN:                 0                  0
  Frames BECN:                 0                  0
  Frames Abort:                0                  0
  Buf Not Available:           0                  0
  KbpsAIR:                     0                  0
  XmtFramesDiscXceedQDepth:    0
  XmtBytesDiscXceedQDepth:     0
  XmtFramesDuringLMIAlarm:     0
  XmtByteDuringLMIAlarm:       0
  XmtFramesUnderrun:           0
  RcvFramesDE:                                    0
  RcvFramesDiscCRCError:                          0
  RcvFramesDiscIllegalHeader:                     0
  RcvFramesDiscAlignmentError:                    0
  RcvFramesDiscIllegalLen:                        0
  RcvFramesDiscXceedDEThresh:                     0
  RcvFramesUnknownDLCI:                           0
  RcvLastUnknownDLCI:                             0
  RcvFramesTaggedFECN:                            0
  RcvFramesTaggedBECN:                            0
  RcvFramesTaggedDE:                              0
  Status:                      0                  0
  StatusInquiry:               0                  0
  AsynchUpdate:                0                  0
  RcvInvalidRequest:                              0
  RcvUNISeqMismatch:                              0
  RcvNNISeqMismatch:                              0
  UNISignallingTimeout:                           0
  NNISignallingTimeout:                           0
  FramesCLLM:                  0                  0
  BytesCLLM:                   0                  0
  CLLMFailures:                               		    0

dspportq

The dspportq command displays queue information for a specified port and egress queue on the AUSM.

Full Name

display port queue

Syntax

dspportq <port number> <egress queue number>

where:

<port number>	queue number is in the range 1-4
<egress queue number>	egress queue number is in the range 1-12

Related Commands

dspportqs

Cards on which the command executes

AUSM, IM-ATM

Attributes

Log: No State: Any Privilege: 1-6

Example 1 Description

dspportq 1 1

Display queue information for egress queue 1 on port 1.

System Response

Service Port Num:               1
  Q Number:                     1
  Port Bin State:               Enabled
  Service Sequence:             1
  Queue Depth:                  100
  CLP  Threshold High (cells):  100
  CLP  Threshold Low (cells):   100
  EFCI Threshold:               100
  Queue Algorithm:              1
  Max Bandwidth Increment:      0
  Min Bandwidth Increment:      0
  Q CLP State:                  0
  Q Full Discarded Cells:       0
  CLP Set Discarded Cells:      0

dspportqs

The dspportqs command displays queue information for all the egress queues on an AUSM port.

Full Name

display card errors

Syntax

dspportqs <port number>

Related Commands

dspportq

Cards on which the command executes

AUSM

Attributes

Log: No State: Any Privilege: 1-6

Example 1 Description

dspportqs 1

Display egress queue information for all the egress queues on port 1.

System Response

Port   Q Num  State   Q-Algo Service-Seq Depth-Max  CLP-High  CLP-Low  EFCI-Thrsh
----  -----  -----   ------ ----------- ---------  --------  -------  ----------
  1     1    Enabled    3       1           200      180        160      160
  1     2    Enabled    3       2           900      800        700      700
  1     3    Enabled    3       3           900      800        700      700
  4     1    Enabled    3       1           200      180        160      160
  4     2    Enabled    3       2           900      800        700      700
  4     3    Enabled    3       3           900      800        700      700
Syntax : dspportqs

dspports

The dspports command displays information on all the ports on the current card.

Full Name

Display ports

Syntax

dspports

Related Commands

addport, cnfport, delport, dspport

Cards on which the command executes

FRSM

Attributes

Log: No State: Any Privilege: 1-6

Example 1 Description

dspports

Display the ports on the current FRSM.

System Response

   Port   Ena/Speed EQService  SignalType  T391 T392 N391 N392 N393 InAlarm
                       Ratio
  -------- --- ----- --------- ------------ ---- ---- ---- ---- ---- -------
  7.2.1    Add/1536k    1      NoSignalling   10   15    6    3    4   No
  7.2.2    Add/  64k    1      NoSignalling   10   15    6    3    4   No
  7.2.3    Add/  64k    1      NoSignalling   10   15    6    3    4   No
  7.2.4    Add/  64k    1      NoSignalling   10   15    6    3    4   No
  7.2.5    Add/  64k    1      NoSignalling   10   15    6    3    4   No
  7.2.6    Add/  64k    1      NoSignalling   10   15    6    3    4   No
  7.2.7    Add/  64k    1      NoSignalling   10   15    6    3    4   No
  7.2.8    Add/  64k    1      NoSignalling   10   15    6    3    4   No
  7.2.9    Add/  64k    1      NoSignalling   10   15    6    3    4   No
  7.2.10   Add/  64k    1      NoSignalling   10   15    6    3    4   No
  7.2.11   Add/  64k    1      NoSignalling   10   15    6    3    4   No
  7.2.12   Add/  64k    1      NoSignalling   10   15    6    3    4   No
  7.2.13   Add/  64k    1      NoSignalling   10   15    6    3    4   No
  7.2.14   Add/  64k    1      NoSignalling   10   15    6    3    4   No
  7.2.15   Add/  64k    1      NoSignalling   10   15    6    3    4   No
  7.2.16   Add/  64k    1      NoSignalling   10   15    6    3    4   No
  7.2.17   Add/  64k    1      NoSignalling   10   15    6    3    4   No
  7.2.18   Add/  64k    1      NoSignalling   10   15    6    3    4   No
  7.2.19   Add/  64k    1      NoSignalling   10   15    6    3    4   No

dspsarcnt

The dspsarcnt command displays the Segmentation and Reassembly (SAR) counters for the current card.

Full Name

Display SAR counters

Syntax

dspsarcnt <ChanNum>

where ChanNum is:

For FRSM, 16-271
For ASC, 16-1024
For AUSM, 16-271

Cards on which the command executes

ASC, FRSM, AUSM, CESM

Attributes

Log: No State: Any Privilege: 1-6

Example 1 Description

dspsarcnt 22

Display SAR count on the current FRSM, channel 22.

System Response

                          SarShelfNum:         1
                          SarSlotNum:          13
                          SarChanNum:          22
                                Tx                      Rx
                          ---------------       ---------------
  Total Cells:            11227853              11529804
  Total CellsCLP:         0                     0
  Total CellsAIS:         498805                0
  Total CellsFERF:        0                     302222
  Total CellsEnd2EndLpBk: 0                     0
  Total CellsSegmentLpBk: 0                     0
  RcvCellsDiscOAM:                              0
Syntax : dspsarcnt "chan_num"
         channel number -- value ranging from 16 to 271
        possible errors are :
        a) illegal/invalid parameters
        b) channel doesn't exist

Example 2 Description

dspsarcnt 98

Display SAR count for channel 98 on the current card (an AUSM).

System Response

                          SarShelfNum:         1
                          SarSlotNum:          4
                          SarChanNum:          98
                                Tx                      Rx
                          ---------------       ---------------
  Total Cells:            141357                0
  Total CellsCLP:         0                     0
  Total CellsAIS:         0                     0
  Total CellsFERF:        0                     0
  Total CellsEnd2EndLpBk: 0                     0
  Total CellsSegmentLpBk: 0                     0
  RcvCellsDiscOAM:                              0
Type <CR> to continue, Q<CR> to stop:
                          SarShelfNum:         1
                          SarSlotNum:          4
                          SarChanNum:          114
                                Tx                      Rx
                          ---------------       ---------------
  Total Cells:            283600                296016
  Total CellsCLP:         0                     0
  Total CellsAIS:         0                     0
  Total CellsFERF:        0                     0
  Total CellsEnd2EndLpBk: 0                     0
  Total CellsSegmentLpBk: 0                     0
  RcvCellsDiscOAM:                              0
Type <CR> to continue, Q<CR> to stop:
Q

dspshelfalm

The dspshelfalm command displays the shelf alarms for the AXIS. If no alarm number is specified, the status of every alarm is displayed. See the example for the number for each alarm.

In the dspshelfalm display, the State column shows whether the alarm has been asserted. "Normal" means that no alarm has been asserted. If an alarm were asserted, State would show "Above Normal" or "Below Normal". The presence of the word "missing" in the State column means that the input is missing or ignored. The content of the Severity column indicates what the severity of the alarm would be if the alarm were asserted.

Full Name

Display shelf alarms

Syntax

dspshelfalm [alarm number]

Related Commands

none

Cards on which the command executes

ASC

Attributes

Log: No State: Active Privilege: 1-6

Example 1 Description

dspshelfalm

Display the status of all the shelf alarms.

System Response

 Alarm     Type     Unit Thresh Severity Measurable Val State
 ----- ------------ ---- ------ -------- ---------- --- -----
   1   Temperature    1  50      Minor      Yes    40  Normal
   2   Power Supply   1  0       Minor      No     0   missing
   3   Power Supply   2  0       Minor      No     0   missing
   4   DC Level       1  42-54   Minor      Yes    0   missing
   5   DC Level       2  42-54   Minor      Yes    47  Normal
   6   Fan Unit       1  2000    Minor      Yes    0   missing
   7   Fan Unit       2  2000    Minor      Yes    0   missing
   8   Fan Unit       3  2000    Minor      Yes    0   missing
   9   Fan Unit       4  2000    Minor      Yes    0   missing
   10  Fan Unit       5  2000    Minor      Yes    0   missing
   11  Fan Unit       6  2000    Minor      Yes    0   missing
  ASMNumOfValidEntries: 11
  ASMShelfAlarmState:   2

dspslotlnk

The dspslotlnk command displays SRM-3T3 link information for a specified slot.

Full Name

Display slot link

Syntax

dspslotlnk <slot number>

where:

slot number for which the links are to be displayed

Related Commands

delslotlnk

Cards on which the command executes

SRM-3T3

Attributes

Log: No State: Active Privilege: 1

System Response

SlotLine	T3Line	T1
7.1	1	1
7.2	1	2
7.3	1	3
7.4	1	4

dspsmcnf

The dspsmcnf command displays configuration enables for the service modules in the system. The output displays the following for each service module slot:

Whether a card is present and a configuration exists
Whether rate control is on or off
Whether the card is channelized
The number of the MIB version

Full Name

Display service module configuration.

Syntax

dspsmcnf

Related Commands

clrsmcnf

Cards on which the command executes

ASC

Attributes

Log: Yes State: Any Privilege: 1-6

Example 1 Description

dspsmcnf

System Response

axis3.1.3.ASC.a > dspsmcnf
         slot #     Config       Config       Rate        Channelized      MIB
                  Card Type      exist       Control                     Version
         ------   ---------      ------      -------      -----------     ------
            5        --            No          Off            Off            0
            6        --            No          Off            Off            0
            7     FRSM-4T1        Yes          Off            Off            5
            8        --            No          Off            Off            0
            9        --            No          Off            Off            0
           10        --            No          Off            Off            0
           11     FRSM-4E1        Yes           On             On            5
           12     FRSM-4T1        Yes           On             On            5
           13     FRSM-4T1        Yes           On             On            5
           14     AUSM-4T1        Yes           On             Off           4
axis3.1.3.ASC.a >

dspsrmclksrc

The cnfsrmclksrc command displays the SRM 3T3 clock source for a specified T3 line.

Full Name

Display SRM clock source

Syntax

dspsrmclksrc -ds3<T3 line number>

where:

the SRM-3T3 T3 line number (range 1-3)

Related Commands

cnfsrmclksrc

Cards on which the command executes

SRM-3T3

Attributes

Log: No State: Active Privilege: 1

System Response:

T3Line	lineXmtClockSource
1.1	backplane clock from BNM
1.2	backplane clock from BNM
1.3	backplane clock from BNM

dsptrapmgr

The dsptrapmgr command displays a list of all the SNMP Managers that receive traps.

Full Name

Display trap managers

Syntax

dsptrapmgr

Related Commands

cnftrapmgr

Cards on which the command executes

ASC

Attributes

Log: No State: Any Privilege: 1-6

Example 1 Description

dsptrapmgr

System Response

     ipAddress     PortNum  RowStatus   ReadTrapFlag  NextTrapSeqNum
  ---------------  -------  ----------  ------------  --------------
  192.168.3.251      2500       Add           Off       571
  192.168.3.254      2500       Add           Off       631
  LastTrapSeqNum:  631
  NumOfValidEntries:  2

dspds3ln

This command displays the parameters of the DS3 line

Full Name

Display DS3 line

Syntax

dspds3ln "line_num"

where:

"line_num"

value of 1 is accepted for IMATM-T3T1/E3E1

Example: dspds3ln "1"

Related Commands

dspds3lns

Cards on which the command executes

IM-ATM

Attributes

Log: Yes State: Active Privilege: 1-2

Example: dspds3ln "1"

LineNum:	1
LineType:	dsx3CbitParity
LineCoding:	dsx3B3ZS
LineLength:	< 450 ft.
LineOOFCriteria:	3 Out of 8
LineAIScBitsCheck:	Ignor C-bit
LineLoopbackCommand:	NoLoop
LineRcvFEACValidation:	4 Out of 5

Attributes

Log: No State: Active Privilege: 1-6

Example 1 Description

dspusers

Display the users configured for this shelf. The users in this example are Raoul and Duke.

System Response

    User Id      level
  StrataCom      -2
    Service      -1
  SuperUser       0
      raoul       3
       duke       1

Example 1 Description

Help

Display the commands available on the current card. In this case, the card is an ASC.

System Response

dsptrapmgr
clrmsgcnt
clrsarcnt
dspadrxlat
cnfalm
dspalmcnf
cnfcnt
clrbnmcnt
cnfifip
dspifip
cnftime
cnfdate
cnfname
cnfclksrc
dspclksrc
dspshelfalm
dspbnmcnt
dspcd
dspsarcnt
dspmsgcnt
dspalm
dspalms
dspalmcnt
dspln
dsplns
dspcds

modbert

The modbert command modifies the shelf for bit error rate testing.

Full Name

Modify Bit Error Rate Test

Syntax

modbert

Related Commands

dspbert, cnfbert, delbert

Cards on which the command executes

ASC

myid

Displays the login name of the current user.

Full Name

My ID

Syntax

myid

Related Commands

none

Cards on which the command executes

ASC, FRSM, AUSM

Attributes

Log: No State: Any Privilege: 1-6

Example 1 Description

myid

Display the login name of the current user.

System Response

StrataCat

resetcd

The resetcd command resets the hardware or failure history on the current ASC. Without a slot number, the command resets only the ASC. With a slot number, resetcd resets the card in the specified slot.

Full Name

Reset card

Syntax

resetcd [slot number]

Related Commands

none

Cards on which the command executes

ASC

Attributes

Log: Yes State: Active Privilege: 1-3

switchcc

The switchcc command switches control of the AXIS from the active ASC/BNM core card group to the standby ASC/BNM. The ASC in slot 3 is associated with the BNM in slot 1. The ASC in slot 4 is associated with the BNM in slot 2. If the standby cards are not available, the command is not executed.

FRSM, AUSM, CESM

Attributes

Log: No State: Active Privilege: 1-4

Example 1 Description

tstdelay 16

Test the delay for a round trip to and from the network on channel 16.

System Response

axis61.1.10.AUSM.a > tstdelay 16
TestDelay in progress.
TestDelay Passed with 2 ms.
axis61.1.10.AUSM.a >

upport

The upport command ups a port. No messages appear on screen unless an error occurs.

Full Name

Up port

Syntax

upport <PortNum>

where:

PortNum = 1-4

Related Commands

dnport

Cards on which the command executes

AUSM

Attributes

Log: Yes State: Active Privilege: 1

users

Lists the users logged into the current card. The screen display shows the means through which each user logged into the shelf, the slot number of the current card, and the login name of the users.

Full Name

Users

Syntax

users

Related Commands

none

Cards on which the command executes

ASC

Attributes

Log: No State: Any Privilege: 1-6

Example 1 Description

users

Display the users logged into the current ASC.

System Response

 Port    SlotNum    user ID
Telnet      4       StrataCat

version

The version command displays different types of version-related information, such as firmware version, operating system kernel version, the date of the software build, and so on (refer to screen examples).

Full Name

display versions

Syntax

version

Related Commands

none

Cards on which the command executes

ASC, FRSM, AUSM, CESM, IM-ATM

Attributes

Log: No State: Any Privilege: 1-6

Example 1 Description

version
Display version information on the current card (ASC).
***** StrataCom Inc. AXIS ASC Card *****
Firmware Version           =     shenlee
Backup Boot version        =     model-B BT_2.1.2
ASCFRSM Xilinx file        =     asc025.h
ASCBNM Xilinx file         =     bnm_newIte
ASCBNM Altera file         =     bnm155
SRM-T1E1 Xilinx file       =     srm038.h
SRM-3T3 Encoder file       =     encoder42_004.ttf
SRM-3T3 Encoder-2 file     =     encoder80_001.ttf
SRM-3T3 Decoder file       =     decoder42_004.ttf
SRM-3T3 Clock file         =     clkctrl_37.ttf
SRM-3T3 I-Cube file        =     ic320.h
VxWorks (for StrataCom) Version 5.1.1-R3000
Kernel: WIND version 2.4
Made on Thu Mar 20 16:53:19 PST 1997
Boot line:
ln (0.0)

System Response

axis3.1.3.ASC.a > version

***** Stratacom Inc. AXIS ASC Card *****2
Firmware Version	=	shenlee
Backup Boot version	=	model-B BT_2.1.2
ASCFRSM Xilinx file	=	asc025.h
ASCBNM Xilinx file	=	bnm_newIte
ASCBNM Altera file	=	bnm155
SRM-T1E1 Xilinx file	=	srm038.h
SRM-3T3 Encoder file	=	encoder42_004.ttf
SRM-3T3 Encoder-2 file	=	encoder80_001.ttf
SRM-3T3 Decoder file	=	decoder42_004.ttf
SRM-3T3 Clock file	=	clkctrl_37.ttf
SRM-3T3 I-Cube file	=	ic320.h
VxWorks (for STRATACOM) version 5.1.1-R3000.
Kernel: WIND version 2.4.
Made on Wed Feb 14 16:06:24 PST 1996.
Boot line:
sl(0,0)

axis3.1.3.ASC.a >

Example 2 Description

version

Display version information on the current card (FRSM).

System Response

axis3.1.11.FRSM.a > version
***** Stratacom Inc. AXIS FRSM Card *****
    Firmware Version    = eqa2.0.1g
    Backup Boot version = model-B BT_2.0.0
    ASCFRSM Xilinx file = frsm025.h
VxWorks (for STRATACOM) version 5.1.1-R3000.
Kernel: WIND version 2.4.
Made on Wed Feb 14 16:15:08 PST 1996.
Boot line:
axis3.1.11.FRSM.a >

Example 3 Description

version

Display version information on the current card (AUSM).

System Response

axis3.1.14.AUSM.a > version
***** StrataCom Inc. AXIS AUSM Card *****
    Firmware Version    = model-A 2.0.00
    Backup Boot version = model-A BT_eqa2.0.1
    AUSM Xilinx file = ausmfract.h
VxWorks (for STRATACOM) version 5.1.1-R3000.
Kernel: WIND version 2.4.
Made on Fri Feb 9 18:59:08 PST 1996.
Boot line:
axis3.1.14.AUSM.a >

Table of Contents