Super User Commands

Introduction

This chapter contains detailed descriptions of the IPX/IGX/BPX Software Release 8.5 super user commands. The IPX/IGX/BPX super user command descriptions appear in alphabetical order. Access to these commands requires user-privilege level 0 (zero).

Caution  Use of these commands should be restricted to Cisco personnel and other qualified users, such as System Administrators. Do not distribute this information to casual users because improper use of some super user commands may lead to system malfunction or complete failure.

General Information

Table 1-1 lists the IPX/IGX/BPX level 0 (super user) commands in alphabetical order. The table also lists the nodes on which each command is available and whether you can include the command in a job. To access these commands, type in SuperUser at the login prompt. Enter the super user password and the password prompt. To exit a command at any point, press the Delete key.

The screen examples in this chapter are based on a network containing an IPX, IGX, or BPX or any combination of these nodes. For detailed descriptions of commands requiring a user-privilege level in the range 1-6, refer to the Cisco StrataCom Command Reference.

Command Help

The StrataView Plus workstation provides on-line help for all IPX/IGX/BPX commands. On-line help can be accessed through the StrataView Plus FrameViewer icon. On-line help provides an abbreviated version of the information in this document, including the command function, syntax, and attributes. Hypertext links allow you to navigate through the various commands.

Commands

The pages that follow contain the description of the super user commands in alphabetical order. Whenever applicable, the command description includes a description of the options and at least one example of a screen display for the command.

burnfwrev (Burn Firmware Image into Card(s)

The burnfwrev command burns a new firmware image into a specific card.

Attributes

Jobs: Yes Log: Yes Lock: Yes Node Type: IPX, IGX, BPX

Associated Commands

dspfwrev, getfwrev

Syntax

Function

This command is used to burn a firmware image into the memory of a specific card. Before you use burnfwrev, the firmware image must already reside in the controller card's memory. (Use getfwrev to load the image to the controller.).

A few seconds after you enter burnfwrev, the system displays a screen similar to the one in Figure 1-1, then the Burn Address column starts to indicate the addresses that are being "burned." When burnfwrev finishes, the status changes to "Complete."

After all cards at a node have been updated with burnfwrev, enter the following to clear the firmware image from the controller card's buffer area:

Use the dspfwrev command to display the firmware image status on the controller card at any time after burnfwrev has finished.

At the super user level (0), you can use burnfwrev only to change the revision level of a card's firmware. If the firmware revision would result in a new model number for the card, only a user with a higher privilege level can burn the firmware image. In this case, you would have to call the TAC to execute the command.

gamma            TRM       SuperUser        Rev: 8.5 Aug. 17 1997  14:28 PDT 
Firmware        Size        Status                                              
F.D.A           256 K       Burning into slot 19 (6 lives)                      
File            Address     Length      CRC           Burn Address              
0               800000      10          E986E939                                
1               800800      410         22996DDA                                
2               801000      2D40        B212147F                                
3               805E60      480         85CB29EA                                
4               80A630      70          57A938AE                                
5               80A6B0      20          4B9E8DDC                                
6               810000      10000       338E45F6                                
7               820000      4400        95990113                                
8               835000      1810        875771B2                                
9               8368A0      15D0        4C597B97                                
This Command: burnfwrev                                                         
Continue?

clrcderrs (Clear Detailed Card Errors)

The clrcderrs command clears the history of card failures (errors) associated with the specified slot.

Attributes

Jobs: Yes Log: Yes Lock: Yes Node Type: IPX, IGX, BPX

Associated Commands

dspcderrs, prtcderrs

Syntax

Function

This command clears the history of card failures associated with the specified slot. When you enter this command system responds with Slot Number or *. After you enter the command, the system asks you to confirm that it is OK to clear this data.

For example, to clear the data from the FRM card in slot 3, enter the command illustrated in Figure 1-2. This screen also illustrates the card's stored data.

pubsigx1       TN    StrataCom       IGX 32    8.5       Aug. 5 1997  18:48 GMT
FRM in Slot 3  : 172240 Rev ESJ     Failures Cleared: Date/Time Not Set
----------------------------------- Records Cleared:  Date/Time Not Set
Self Test          Threshold Counter: 0          Threshold Limit: 300
Total Pass: 495           Total Fail: 0              Total Abort: 2
First Pass: Date/Time Not Set          Last Pass: July 29 1997 19:36:48 GMT
First Fail:                            Last Fail:
Background Test    Threshold Counter: 0          Threshold Limit: 300
Total Pass: 29849         Total Fail: 0              Total Abort: 0
First Pass: Date/Time Not Set          Last Pass: Aug. 5 1997  18:46:34 GMT
First Fail:                            Last Fail:
Hardware Error     Total Events: 0     Threshold Counter: 0
First Event:                           Last Event:
This Command: clrcderrs 3
OK to clear (y/n)?

After replying 'y' (yes) to the confirmation prompt, the screen appears as in Figure 1-3.

pubsigx1       TN    StrataCom       IGX 32    8.5       Aug. 5 1997  18:55 GMT
FRM in Slot 3  : 172240 Rev ESJ     Failures Cleared: Date/Time Not Set
----------------------------------- Records Cleared:  Aug. 5 1997  18:55:02 GMT
Self Test          Threshold Counter: 0          Threshold Limit: 300
Total Pass: 0             Total Fail: 0              Total Abort: 0
First Pass:                            Last Pass:
First Fail:                            Last Fail:
Background Test    Threshold Counter: 0          Threshold Limit: 300
Total Pass: 0             Total Fail: 0              Total Abort: 0
First Pass:                            Last Pass:
First Fail:                            Last Fail:
Hardware Error     Total Events: 0     Threshold Counter: 0
First Event:                           Last Event:
Last Command: clrcderrs 3
Next Command:

clrcnf (Clear Configuration Memory)

The clrcnf command clears the configuration memory at the current node and resets the node.

Attributes

Jobs: No Log: No Lock: Yes Node Type: IPX, IGX, BPX

Associated Commands

loadcnf, runcnf, savecnf

Syntax

Function

The clcnf command erases most network configuration data. This configuration data includes connections, trunks, circuit lines, and so on, for the local node. You may need to use the clcnf command when you upgrade the network with a new software release or when you move a node. Before the command executes, a warning and a confirmation prompt. Figure 1-4 illustrates a typical screen.

This command should be used only on a node that has not yet been placed in service or when the network configuration has been previously saved so it can be quickly reloaded. The configuration can be saved in one of several ways:

• On a StrataView Plus terminal using the savecnf command. The node is then reloaded using the loadcnf command.

• On a standby controller card. Before entering the clrcnf command, remove the standby controller from its slot. The configuration data will be maintained in BRAM even though the power has been removed from the card.

Caution  Use clrcnf with extreme caution. Typically, you should use clrcnf only if the WANBU TAC has instructed you to do so. This command can make the node unreachable to the network.

*** Warning: ***                                                                
This command clears the configuration memory and resets the Node.               
This Command: clrcnf                                                            
Are you sure (y/n)?

clrfpevt (Clear FastPAD Event Reporting)

The clrfpevt command disables the reporting of FastPAD events.

Attributes

Jobs: No Log: Yes Lock: No Node Type: IPX, IGX

Associated Commands

setfpevt, dsplog

Syntax

Function

The reason for executing clrfpevt is to prevent the large number of logged events that accumulate when certain user-controlled disruptions occur. Without suspension of event-logging, the number of events caused by the disruption can cause the FastPAD to become unreachable. Remember to resume event logging by using the setfpevt command. Examples of these events are:

• FTM Y-cable switchover

• NPM/NPC switchover

• Adding a connection by using the addfrcons command

• Resetting the FastPAD (power cycling or by the resetfp command).

Example

clfpevt 9.3

Description

The example command halts event logging for the FastPAD connected to port 9.3.

sw152          TN    StrataCom       IGX 16    8.5 Nov. 26 1997 15:14 GMT 
 
Most recent log entries (most recent at top)
Class  Description                                             Date     Time    
Info   FP fp93 event: 9.3.B grp:0-0 code:12                    11/26/97 15:13:28
Info   FP fp93 event: 9.3.B grp:0-0 code:1                     11/26/97 15:13:28
Info   User StrataCom logged in (Local)                        11/26/97 14:28:40
Info   User StrataCom logged in (Local)                        11/26/97 12:56:49
Info   Invalid Login Attempt via LAN Port (Local)              11/26/97 12:56:46
Info   User StrataCom logged in (Local)                        11/26/97 11:31:51
Info   AD  9.2.3   dallas   COM OK (Kickoff)                   11/26/97 11:23:17
Info   AD  9.2.3   dallas   Unreachable                        11/26/97 10:59:32
Info   AD  9.2.3   dallas   COM OK (Kickoff)                   11/26/97 10:56:54
Info   FP fp93 event: 9.3.B grp:0-0 code:12                    11/25/97 18:16:45
Info   FP fp93 event: 9.3.B grp:0-0 code:1                     11/25/97 18:16:45
                                                                                
Last Command: dsplog
 
 
Next Command: 

cnfcdpparm (Configure CDP Card Parameters)

The cnfcdpparm command configures parameters for the CVM or CDP.

Attributes

Jobs: No Log: Yes Lock: Yes Node Type: IPX, IGX

Associated Commands

cnfchts, dchst, cnfecparm

Syntax

Function

The cnfcdpparm command lets you configure CDP or CVM parameters for Modem Detection (MDM), certain reserved debug parameters, and In Frame and Out of Frame (I Frm and O Frm) thresholds for DS0A-type T1 applications. (See the cnfln description for information on assigning % Fast Modem on a per-channel basis.) Table 1-2 lists the cnfcdpparm parameters. All CDPs or CVMs in the node are dynamically reconfigured according to the new parameters. When you enter the command, the system prompts for a parameter number, as Figure 1-5 illustrates.

Caution You should consult the Cisco TAC before changing any of these parameters.

pubsigx1       TN    StrataCom       IGX 32    8.5 Oct. 20 1997 18:06 PDT 
1   MDM Low  Pwr Thrsh      [3160] (H)  15  0 Frm 4.8 Thrsh (msecs) [ 500] (D)
2   MDM Stationary Coef.    [  14] (H)  16  I Frm 9.6 Thrsh (msecs) [ 500] (D)
3   MDM ZCR High Frq Thrsh  [  5A] (H)  17  O Frm 9.6 Thrsh (msecs) [ 500] (D)
4   MDM ZCR Low  Frq Thrsh  [  56] (H)
5   MDM Detect Failure Cnt  [   4] (H)
6   MDM Detect Window Min.  [  39] (H)
7   MDM Detect Silence Max. [  24] (H)
8   MDM Pkt Header          [   6] (D)
9   Null Timing Pkt Header  [   4] (D)
10  Debug Parm A            [   0] (H)
11  Debug Parm B            [   0] (H)
12  I Frm 2.4 Thrsh (msecs) [ 500] (D)
13  O Frm 2.4 Thrsh (msecs) [ 500] (D)
14  I Frm 4.8 Thrsh (msecs) [ 500] (D)
                                                                                
This Command: cnfcdpparm  
 
Which parameter do you wish to change:

cnfcftst (Configure Communication Fail Test Pattern)

The cnfcftst command changes the test pattern for communication failure testing.

Attributes

Jobs: No Log: Yes Lock: Yes Node Type: IPX, IGX, BPX

Associated Commands

dspcftst

Syntax

Function

The communication fail test pattern is used to periodically test for failure of nodes to communicate with each other. This test pattern is also used to recover from communication fail conditions. A communication fail is defined as a loss of controller communication over one or more trunks to a particular node. A communication fail differs from a communication break condition in that the node may be reachable over other paths. The communication fail test is used to test the failed trunk for proper controller traffic.

This command allows the user to configure the communication fail test pattern byte-by-byte. It defaults to a pattern of 4 bytes of 1s followed by 4 bytes of 0s. Varying the length of the test pattern makes the communications test more or less rigorous. Changing the characters determines the pattern sensitivity for strings of less than 14 bytes.

The dspcftst command displays the current communication test pattern. The parameters used for declaring and clearing communication fails are set by the cnfnodeparm command. Figure 1-6 illustrates a typical screen.

pubsigx1       TN    StrataCom       IGX 32    8.5       Feb 24 1997 21:17 GMT
Comm Fail Test Pattern
==> Byte  0: FF     Byte 12: 00     Byte 24: FF     Byte 36: 00     Byte 48: FF
    Byte  1: FF     Byte 13: 00     Byte 25: FF     Byte 37: 00     Byte 49: FF
    Byte  2: FF     Byte 14: 00     Byte 26: FF     Byte 38: 00     Byte 50: FF
    Byte  3: FF     Byte 15: 00     Byte 27: FF     Byte 39: 00     Byte 51: FF
    Byte  4: 00     Byte 16: FF     Byte 28: 00     Byte 40: FF     Byte 52: 00
    Byte  5: 00     Byte 17: FF     Byte 29: 00     Byte 41: FF     Byte 53: 00
    Byte  6: 00     Byte 18: FF     Byte 30: 00     Byte 42: FF     Byte 54: 00
    Byte  7: 00     Byte 19: FF     Byte 31: 00     Byte 43: FF     Byte 55: 00
    Byte  8: FF     Byte 20: 00     Byte 32: FF     Byte 44: 00     Byte 56: FF
    Byte  9: FF     Byte 21: 00     Byte 33: FF     Byte 45: 00     Byte 57: FF
    Byte 10: FF     Byte 22: 00     Byte 34: FF     Byte 46: 00     Byte 58: FF
    Byte 11: FF     Byte 23: 00     Byte 35: FF     Byte 47: 00     Byte 59: FF
This Command: cnfcftst
Enter Byte 0:

cnfchstats (Configure Channel Statistics Collection)

The cnfchstats command enables statistics collection for various channel parameters.

Attributes

Jobs: Yes Log: Yes Lock: Yes Node Type: BPX, IGX, IPX

Associated Commands

dspchstatcnf

Syntax

Function

This debug command enables statistics collecting for channel parameters. Table lists the statistics by type. Not all statistic types are available for all connections. Only valid statistics are displayed for you to select; inapplicable statistics appear in gray. If you are unsure of the size parameter to specify, select four bytes per sample.

The dspchstatcnf command displays the channel statistics configuration. Statistics are collected by and displayed on the StrataView Plus workstation. StrataView Plus allows statistics collection to be customized. A StrataView Plus-enabled channel statistic may be disabled by specifying the optional node name of the workstation as the last parameter on the command line.

cnfchts (Configure Channel Timestamp)

The cnfchts command configures a pre-aging parameter for data channels. Applicable cards are the SDP, LPD, LDM, and HDM. Applicable traffic is time-stamped data.

Attributes

Jobs: Yes Log: Yes Lock: Yes Node Type: IPX, IGX

Associated Commands

cnfcdpparm

Syntax

Function

This command configures the pre-age parameter for data channels. The pre-age parameter specifies the initial age of a time-stamped packet. With a non-zero pre-age, the packet has less time to wait at the destination before it reaches the Max Time Stamped Packet Age and is taken out of the ingress queue. (Data channels with the greater pre-age value are processed sooner.) However, if the pre-age value is too high because of queuing delays in the network, packets could be discarded because they appear too old at the destination.

The value you enter for Pre-Age should be a multiple of 250 microseconds (otherwise, the system rounds the value down to the nearest multiple of 250 microseconds.) The default value is 0. Acceptable values are in the range 0 to the Max Time Stamped Packet Age (set by the cnfsysparm command). After you finish entering this command, the screen as in the example. After you change a timestamp, the connection should be rerouted or restarted for the new value to take effect.

Example

pubsipx1       TN    StrataCom       IPX 16    8.5.00    Aug. 14 1997 03:50 GMT 
 
            Maximum EIA     %      DFM Pattern     DFM        PreAge
Channels    Update Rate    Util      Length       Status      (usec)  
3.1               2        100         8         Enabled        1000
3.2-4             2        100         8         Enabled           0
 
 
 
 
 
 
 
 
 
 
 
                                                                                
Last Command: cnfchts 3.1 1000
 
 
Next Command: 

cnfclnparm (Configure Circuit Line Parameter)

The cnfclnparm command configures the alarm integration time for circuit lines originating on a UVM, CDP or CVM and for T1/E1 Frame Relay circuits originating on an FRP, FRM, or UFM.

Attributes

Jobs: No Log: Yes Lock: Yes Node Type: IPX, IGX

Associated Commands

cnfclnsigparm, dchst

Syntax

Function

This command configures the circuit line alarm integration times for RED and YELLOW circuit line alarms. These integration times are specified in milliseconds and should be set to correspond to the local carrier's alarm integration times. Carrier integration times are typically 800 to 1500 ms. for RED Alarm and 1500 to 3000 ms. for YELLOW Alarm. The allowable range for these parameters are 60 to 3932100 ms. When you enter this command system responds with the screen in Figure 1-7.

D1.gamma         TRM       SuperUser        Rev: 8.5  Aug. 14 1997  14:27 PDT 
CLN 11 Parameters                                                               
 1  Red Alarm - In/Out  [  1000 /   2000] (Dec)                                 
 2  Yel Alarm - In/Out  [  1000 /   2000] (Dec)                                 
This Command: cnfclnparm 11                                                     
Which parameter do you wish to change:

cnfclnsigparm (Configure Circuit Line Signaling Parameters)

The cnfclnsigparm command configures signalling parameters for a UVM, CVM or CDP.

Attributes

Jobs: No Log: Yes Lock: Yes Node Type: IPX, IGX

Associated Commands

cnfclnparm, dspsig

Syntax

Function

The cnfclnsigparm command configures any of the UVM, CVM or CDP circuit line signalling parameters associated with the node. See Table for the parameters and their values.

When you enter this command system as follows, the system responds with the display as shown in Figure 1-8.

sw83           TN    StrataCom       IPX 16    8.5.   Aug. 1 1997  15:26 PST
1  CDP & CIP Heartbeat                    [   2] (sec)
2  CDP & CIP Sig. Polling Rate            [  10] (sec)
3  CDP & CIP Default Inband Sig Delay     [  96] (msec)
4  CDP & CIP Default Inband Playout Delay [ 200] (msec)
5  CDP & CIP Default Pulse Sig Delay      [  96] (msec)
6  CDP & CIP Default Pulse Playout Delay  [ 200] (msec)
7  CIP Number of Packet Slices            [   1]
8  CDP & CIP Packet Rate                  [ 200] (pkt/sec)
9  CDP & CIP Condition CCS Lines?         [  NO]
10 CIP Default Inband Min. Wink           [ 140] (msec)
11 CIP Default Pulse Min. Wink            [ 140] (msec)
This Command: cnfclnsigparm
Which parameter do you wish to change:

cnfclnstats (Configure Circuit Line Statistics)

The cnfclnstats command configures parameters for circuit line statistics collection.

Attributes

Jobs: Yes Log: Yes Lock: Yes Node Type: IPX, IGX

Associated Commands

dspchstats

Syntax

Function

This command configures circuit line statistics. The cnfclnstats command lets you customize statistics collection on each circuit line. It primarily applies to debugging and not standard network operation. Table lists the statistics by type. Figure 1-9 illustrates the display.

Not all statistic types are available for all lines. Valid statistics appear in full brightness while unavailable types appear in half brightness.

Figure 1-9 illustrates the screens displayed after entering cnfclnstats.

D2.ipx5        SV+   SuperUser       IPX 16     8.5    Aug. 14 1997  13:28 PDT 
Line Statistic Types                                                            
 1) Bipolar Violations                                                          
 2) Frames Slips                                                                
 3) Out of Frames                                                               
 4) Losses of Signal                                                            
This Command: cnfclnstats 10                                                    
Statistic Type:                                                                 

cnfcmparm (Configure Connection Management Parameters)

The cnfcmparm command configures various connection management parameters for the node.

Attributes

Jobs: Yes Log: Yes Lock: Yes Node Type: IPX, IGX, BPX

Associated Commands

dsprrst, cnftlparm

Syntax

Function

This command configures parameters that affect Adaptive Voice, Rerouting, and Courtesy Up/Down. These parameters are used only at the local node. Table 1-6 lists the parameters, their descriptions, and their default values.

Example

The example shows the two screens required to display all cnfcmparm parameters.

sw66           TN    StrataCom       BPX 15    8.5 Aug. 28 1997 19:49 GMT 
 
1  Normalization Interval    [    2] (D)
2  Max Number To Normalize   [    5] (D)
3  Normalization Logging     [   No]
4  Settling Interval         [    4] (D)
5  Minimum Open Space        [ 1000] (D)
6  Normalization Priority    [ Load]
7  Load Sample Period        [    4] (D)
8  Maximum Routing Bundle    [   24] (D)
9  Reroute Timer             [    0] (secs)
10 Reset Timer on Line Fail  [  Yes]
11 Max Down/Up Per Pass      [   50] (D)
12 Down/Up Timer             [30000] (msecs)
13 Max Route Errs per cycle  [   50] (D)
14 Time between Rrt cycles   [    5] (mins)
15 Max. Rrt Err cycles       [   10] (D)
                                                                                
This Command: cnfcmparm
 
 
Continue? y
sw66           TN    StrataCom       BPX 15    8.5 Aug. 28 1997 19:50 GMT 
 
16 Routing pause timer       [    0] (msecs)
17 Max msgs sent per update  [   10] (D)
18 Send SVC urgent msg       [   No]
19 Max SVC Retry             [    0] (D)
20 Wait for TBL Updates      [   70] (100 msecs)
21 Max Derouting Bndl (0=all)[  500] (D)
22 # of reroute groups used  [   50] (D)
23 Starting size of RR grps  [    0] (CLU)
24 Increment between RR grps [  100] (CLU)
 
 
                                                                                
This Command: cnfcmparm  
 
 
Enter parameter index: 

cnfdiagparm (Configure Diagnostic Test Parameter)

The cnfdiagparm command sets various diagnostic test parameters for the nodes.

Attributes

Jobs: No Log: Yes Lock: Yes Node Type: IPX, IGX, BPX

Associated Commands

cnftstparm

Syntax

See Table 1-7.

Function

This command sets several parameters that affect the three IPX/IGX/BPX automatic diagnostic tests. Use this command to set test parameters on the internal system clock. Table lists the parameters, their descriptions, and their default values.

When you enter this command, the system responds with the screen illustrated in Figure 1-11.

D2.att7      SV        SuperUser      IPX 16    8.5     Aug. 13 1997 00:21 GMT
                                                                                
1. Vdp Test Frequency (seconds)       [50]                                      
2. LDP tstport delay                  [10]                                      
3. System clock drift (8.192 MHz)  +- [480]                                     
4. UEC-B's PLL railing (8.192 MHz) +- [2720]                                    
5. NPC's PLL minimum (8.192 MHz)    - [92000]                                   
6. NPC's PLL maximum (8.192 Mhz)    + [508000]                                  
7. Clock Test Window                  [10]                                      
8. Clock Test Max Error in Window     [4]                                       
9. Clock Fault Isolation Window       [10]                                      
10. Clock Fault Max Error in Window   [3]                                       
11. Clock Test Frequency (msec)       [200]                                     
12. Clock Test Switch Delay (msec)    [3000]                                    
13. Card Reset Threshold              [255]                                     
14. Card Reset Increment              [0]                                       
                                                                                
                                                                                
This Command: cnfdiagparm                                                       
                                                                                
                                                                                
Enter index of value to be changed:    
                                                                     

cnfdlparm (Configure Download Parameters)

The cnfdlparm command sets various software and firmware downloader parameters.

Attributes

Jobs: No Log: Yes Lock: Yes Node Type: IPX, IGX, BPX

Associated Commands

dspdnld

Syntax

Function

This command sets parameters that affect the SW/FW download protocol. It is primarily a debug command. It is included only for the possibility that some future software or firmware revision may need to be adjusted for optimizing the downloading process. See Table for descriptions of the downloading parameters.

Caution  You should not change downloader parameters except under specific direction from the Technical Assistance Center (TAC). Contact the TAC through Customer Engineering.

Parameters

When you enter cnfdlparm, the system displays an indexed list of parameters. Table 1-8 describes these parameters, and Figure 1-12 illustrates the cnfdlparm screen.

When you enter this command the system responds with the screen illustrated in Figure 1-12.

pubsbpx1       VT    StrataCom       BPX 15    8.5       May  24 1997 23:18 GMT
1  Rmt Blk Freq (msec)     [    100]    16 FW Dnld Msgs/Block(dec) [      4]
2  Rmt Blk Size (hex)      [    400]    17 Flash Write TO(msec)    [  16000]
3  Lcl Blk Freq (msec)     [    100]    18 Flash Erase TO(msec)    [    100]
4  Lcl Blk Size (hex)      [    400]    19 Erase Verify TO(msec)   [  16000]
5  Image Req Freq (msec)   [  10000]    20 Standby Flash TO(sec)   [    300]
6  Dnld Req Freq (msec)    [  10000]    21 Lcl Flash Init TO(msec) [   1000]
7  Session Timeout (msec)  [  30000]    22 Flsh Write Blk Sz (hex) [  10000]
8  Request Hop Limit (dec) [      1]    23 Flsh Verfy Blk Sz (hex) [    400]
9  Crc Throttle Freq (dec) [   5000]    24 Chips Per Write/Erase   [      1]
10 Crc Block Size (hex)    [    400]
11 Rev Change Wait(dec)    [      0]
12 CCs Switch Wait(dec)    [   1000]
13 Lcl Response TO(msec)   [   5000]
14 Rmt Response TO(msec)   [  20000]
15 FW Dnld Block TO(msec)  [     50]
This Command: cnfdlparm
Which parameter do you wish to change:

cnfecparm (Configure Echo Canceller Parameters)

The cnfecparm command configures the CDP or CVM integrated echo canceller (IEC) parameters for specified voice circuit line.

Attributes

Jobs: Yes Log: Yes Lock: Yes Node Type: IPX, IGX

Associated Commands

cnfchec, dspecparm

Syntax

Function

The cnfecparm command configures the UVM, CVM or CDP integrated echo canceller (IEC). It configures IEC parameters associated with all voice channels for the specified circuit line. Setting these parameters allows you to optimize the IEC performance. Table lists the parameters you can modify. The dspecparm command description lists the defaults and provides a sample display. Also, refer to the cnfchec command in the Cisco StrataCom Command Reference for configuring per-channel parameters.

When you enter this command the system responds with the screen illustrated in Figure 1-13.

sw83           TN    StrataCom       IPX 16    8.5    Aug. 1 1997  15:35 PST
IEC Line 7 Parameters
1  CDP IEC Echo Return Loss High (.1 dBs)  [            60] (D)
2  CDP IEC Echo Return Loss Low  (.1 dBs)  [            30] (D)
3  CDP IEC Tone Disabler Type              [         G.164]
4  CDP IEC Non-Linear Processing           [Center Clipper]
5  CDP IEC Non-Linear Processing Threshold [            18] (D)
6  CDP IEC Noise Injection                 [       Enabled]
7  CDP IEC Voice Template                  [           USA]
This Command: cnfecparm 7
Which parameter do you wish to change:

Attributes

Jobs: Yes Log: Yes Lock: Yes Node Type: IPX, IGX

Associated Commands

None

Syntax

Function

This command configures the FastPAD communication parameters. When you enter this command, the system responds as shown in Figure 1-14.

cc7            VT    StrataCom       IPX 32    8.5     Aug. 30 1997 10:05 PST
Last Command: cnffpcom 31.2 2 2 3
Next Command:

cnffpcon (Configure FastPAD Connection Parameters)

The cnffpcon command configures the FastPAD connection parameters.

Attributes

Jobs: Yes Log: Yes Lock: Yes Node Type: IPX, IGX

Associated Commands

addcon, dspcon, dncon, upcon

Syntax

Function

This command configures connection parameters. When you enter this command, the system responds as shown in Figure 1-15.

cc7            VT    StrataCom       IPX 32    8.5     Aug. 30 1997 10:10 PST
Conn:  31.2.B.1   ca12        9.1.B.1     9.6
   MIR       CIR    VC Q Depth      PIR      Cmax   ECN QThresh    QIR    FST
11.6/11.6 11.6/11.6  2048/2048   11.6/11.6   10/10   1024/1024  11.6/11.6  n
% Util: 100/100
Owner: LOCAL  Restriction: NONE  COS: 0                     Status: New Conn
Group: NONE  Priority: N/A  TestRTD: 0 msec
Path:   cc7       19-- 6.2cc1      6.3-- 2.2ca13     1.3--  13ca12
Pref:   Not Configured
cc7       FTC:   OK                    ca12      FTC:   OK
          FTI:   OK                              FTI:   OK
          FastPAD: OK                            FastPAD: OK
This Command: cnffpcon 31.2.B.1 ca12 9.1.B.1
Enter FRP parameters (mir/oe_mir * ...):

cnffpddelay (Configure FastPAD Delay)

The cnffpddelay command configures thresholds for severe congestion (Sc) and mild congestion (Mc) on the FastPAD.

Attributes

Jobs: No Log: Lock: Node Type: IPX, IGX

Associated Commands

none

Syntax

Function

Use this command to set up the delay on the FTC port and subport to which the FastPAD is connected. See Figure 1-16 for a sample screen.

pubsigx1       TN    StrataCom       IGX 32    8.5       Aug. 20 1997 14:07 GMT
Port:          8.1.7.2[FAILED  ]              Configured Clock:   256.0 Kbps
Rcv Clocking:  EXTERNAL                       Measured Clock:           N/A
Xmt Clocking:  EXTERNAL
Data Coding: NRZ
Interface:   V.35
Signalling Protocol      STRATA LMI       Interface Control Template
T391 Link Intg Timer             10
T392 Polling Verif Timer         15           Lead       State
N391 Full Status Poll Cycle      6             CTS        ON
N392 Error Threshold             3             DSR        ON
Monitored Events Count           4             DCD        ON
Severe Congestion (Sc) 64000 (512000)
Mild Congestion (Mc) 57600 (460800)
This Command: cnffpddelay 8.1.7.2
Sc[64000]:

cnffpdpvc (Configure FastPAD PVC)

The cnffppvc command configures the FastPAD bc/bc PVC parameters.

Attributes

Jobs: No Log: Lock: Node Type: IPX, IGX

Associated Commands

none

Syntax

cnffpmap (Configure FastPAD Map Table)

The cnffpmap command configures the FastPAD map table.

Attributes

Jobs: Yes Log: Yes Lock: Yes Node Type: IPX, IGX

Associated Commands

cpyfpmap

Syntax

Function

This command configures FastPAD map table. The map table contains the dialing plan for the FastPAD. When you enter this command, the system responds with the screen shown in Figure 1-17:

cc7            VT    StrataCom       IPX 32    8.5     Aug. 30 1997 10:14 PST
Index  #   DLCI Slot  Index  #   DLCI Slot  Index  #   DLCI Slot  Jump:
[000] 9915 0991  05   [014] FFFF 1023  15   [028] FFFF 1023  15
[001] 0182 0018  02   [015] FFFF 1023  15   [029] FFFF 1023  15
[002] 0528 0052  08   [016] FFFF 1023  15   [030] FFFF 1023  15
[003] 0186 0018  06   [017] FFFF 1023  15   [031] FFFF 1023  15
[004] 0188 0018  08   [018] FFFF 1023  15   [032] FFFF 1023  15
[005] 0524 0052  04   [019] FFFF 1023  15   [033] FFFF 1023  15
[006] 0526 0052  06   [020] FFFF 1023  15   [034] FFFF 1023  15
[007] 0528 0052  08   [021] FFFF 1023  15   [035] FFFF 1023  15
[008] 0528 1023  09   [022] FFFF 1023  15   [036] FFFF 1023  15
[009] FFFF 1023  15   [023] FFFF 1023  15   [037] FFFF 1023  15
[010] FFFF 1023  15   [024] FFFF 1023  15   [038] FFFF 1023  15
[011] FFFF 1023  15   [025] FFFF 1023  15   [039] FFFF 1023  15
[012] FFFF 1023  15   [026] FFFF 1023  15   [040] FFFF 1023  15
[013] FFFF 1023  15   [027] FFFF 1023  15   [041] FFFF 1023  15
This Command: cnffpmap 31.2
Next Command: 

cnffpport (Configure FastPAD Port)

The cnffpport command configures the FastPAD port parameters.

Attributes

Jobs: No Log: Yes Lock: Yes Node Type: IPX, IGX

Associated Commands

dspftcport, dnftcport, upftcport

Syntax

Function

This command configures port parameters for the FastPAD port. When you enter this command, the system responds as in the screen example shown in Figure 1-18.

cc7            VT    StrataCom       IPX 32    8.5     Aug. 30 1997 10:16 PST
                          FastPad Port Configuration
                      Index: 0x0000 Location: 0x30E84C40
     Port in Use   : 01      Port Type     : 02      Conn Exist    : 01
     Phy Port Code : 00      Port Code     : 00      Abs Rate      : 07
                              Data Parameters
[01] Mode          : 00 [02] Baud Rate     : 06 [03] Underrun Fill : 7E
[04] Clock Stop FC : 00 [05] Transmit Clock: 00 [06] Local CTS     : 01
[07] Local CTS Dly : 00 [08] Local DSR     : 01 [09] Local DCD     : 01
[10] Hunt Group Mem: 01 [11] Dest Switch Nm: 01 [12] Dest Port Nm  : 03
[13] Dest Slot/Chnl: 00 [14] Call Timer    : 05 [15] Enable Channel: 01
[16] Initiate Calls: 01 [17] Allocate BW   : 00 [18] Intrframe Fill: 00
[19] DPLL Mode     : 00 [20] Set DE on Data: 00 [21] Async In Timer: 05
[22] Checksum      : 00 [23] Sync Pattern  : 0000
This Command: cnffpport 31.2.B.1
Enter parameter number to change (DEL to quit):

cnffpsys (Configure FastPAD System Parameters)

The cnffpsys command configures the FastPAD system parameters.

Attributes

Jobs: No Log: Yes Lock: Yes Node Type: IPX, IGX

Associated Commands

dspftcport, dnftcport, upftcport

Syntax

Function

This command configures system parameters for the FastPAD port. When you enter this command, the system responds with the screen shown in Figure 1-19:

cc7            VT    StrataCom       IPX 32    8.5     Aug. 30 1997 10:17 PST
                             FastPad Configuration
                      Index: 0x0000 Location: 0x30E9D0B2
     FPD in Use    : 01      Conn State    : 01      FPD Name      : cc7FP
     Alarm Status  : 00      Switched Conn : 01      FPD Index     : 05
     IPX Slot Nm   : 1F      FTC Port Nm   : 01      Link Int      : 01
     Link Rate     : 0C      Card Dsc Index: 00      Avail SwVoice : 00
     Sfail/Nack    : 00/00   TmOut/OutOfSeq: 00/00   Unknown/Q len : 00/00
                             System Parameters
[04] Ring Freq     : 00 [05] Spd Dial Digit: 04 [06] Country Code  : 0100
[07] Line Mgmt Ptcl: 02 [08] Local Swtch Nm: 0C [09] Local Port Nm : 51
[10] Inquire Poll  : 05 [11] Full Stat Poll: 05 [12] Min Frame Size: 22
[13] Max Frame Size: 43 [14] Jitter Buf Sz : 00 [15] User Lockout  : 01
                               Link Parameters
[16] Clock         : 00 [17] Rate          : 0C [18] Bandwidth     : 8000
[19] Data Card Slot: FF [20] Data Card Chnl: 00 [21] Bundled DLCI  : 1000
This Command: cnffpsys 31.2
Enter parameter number to change (DEL to quit)

cnffstparm (Configure ForeSight Node Parameter)

The cnffstparm command configures the ForeSight parameters for Frame Relay ports.

Attributes

Jobs: No Log: Yes Lock: Yes Node Type: IPX, IGX, BPX

Associated Commands

cnffrcon

Syntax

No line or port number need be entered.

Function

This command configures the ForeSight parameters for Frame Relay ports. This command only has an effect if the Frame Relay ForeSight option is enabled. The parameter values set by this command apply to all Frame Relay connections enabled with ForeSight. Therefore, these parameters must be configured on each node in the network that has ForeSight connections. (The cnffrcon command enables ForeSight on a connection.) Table 1-10 lists the parameters. Figure 1-20 and Figure 1-21 illustrate IPX and BPX command menus.

sw83           TN    StrataCom       IPX 16    8.5    Aug. 1 1997  15:41 PST
1  FRP/FTC Increase Rate   [   10] (%)
2  FRP/FTC Decrease Rate   [   87] (%)
3  FRP Fast Decrease Rate  [   50] (%)
4  RTD Measurement Time    [    5] (secs)
5  Default RTD             [  100] (msecs)
6  Minimum RTD             [   40] (msecs)
7  Maximum RTD             [  250] (msecs)
8  FECN for congested mins [   50] (%)
9  QIR Time-out            [   10] (secs)
10 Max TstDelay Retries    [  2] (dec)
This Command: cnffstparm
Enter parameter index:

sw66           TN    StrataCom       BPX 15    8.5 Aug. 28 1997 23:50 GMT 
 
1  FST Increase Rate       [   10] (%)  
2  FST Decrease Rate       [   93] (%)  
3  FST Fast Decrease Rate  [   50] (%)  
4  RTD Measurement Time    [    5] (secs)
5  Default RTD             [  100] (msecs)
6  Minimum RTD             [   40] (msecs)
7  Maximum RTD             [  250] (msecs)
8  FECN for congested mins [   50] (%)  
9  QIR Time-out            [  244] (secs)
10 Max TstDelay Retries    [  2] (dec)
 
 
 
 
 
                                                                                
Last Command: cnffstparm
 
 
Next Command: 

cnflan (Configure LAN)

The cnflan command configures node communication parameters.

Attributes

Jobs: No Log: Yes Lock: Yes Node Type: IPX, IGX, BPX

Associated Commands

upln, dnln, cnfln

Syntax

Function

This command configures node communication parameters, so the node can communicate with a StrataView Plus terminal over an Ethernet LAN using TCP/IP protocol. The parameters all contain address information about the Ethernet TCP/IP network that connects the StrataView Plus station to an IPX, IGX, or BPX node. The values must conform to those of the network. The network administrator can supply the parameters. Refer to the screen in Figure 1-22 .

beta           TRM   YourID:1        IPX 32  8.5     Aug. 15 1997 14:44 MST 
                                                                                
                                                                                
Active IP Address:                     192.0.0.0                                
IP Subnet Mask:                        255.255.255.0                            
TCP Service Port:                      5120                                     
Default Gateway IP Address:            None                                     
                                                                                
Maximum LAN Transmit Unit:             1500                                     
Ethernet Address:                      00.E0.07.00.00.00                        
                                                                                
LAN is not available on the PCC                                                 
                                                                                
                                                                                
                                                                                
                                                                                
                                                                                
                                                                                
Last Command: cnflan
                                                                                
                                                                                
Next Command:       

cnflnparm (Configure ATM Line Card Parameter)

The cnflnparm command configures several parameters for ATM lines originating on the BPX.

Attributes

Jobs: No Log: Yes Lock: Yes Node Type: BPX

Associated Commands

upln, dnln, cnfln

Syntax

Function

This command configures the circuit line alarm integration times for RED and YELLOW circuit line alarms. These integration times are specified in milliseconds and should be set to correspond to the local carrier's alarm integration times. Carrier integration times are typically 800 ms. to 1500 ms for RED Alarm and 1500 to 3000 milliseconds for YELLOW Alarm. The allowable range for these parameters are 60 to 3932100 milliseconds.

You can also set the queue depth for the two queues associated with the ASI-0 card, the constant bit rate (CBR) queue and the Variable Bit Rate (VBR) queue. The queue depths may be increased to 16,000 bytes per queue.

When you enter this command system responds with the screen in Figure 1-23. The cnflnparm command is quite similar to the cnfln command.

sw83           TN    StrataCom       IPX 16    8.5    Aug. 1 1997  15:45 PST
CLN 7 Parameters
 1  Red Alarm - In/Out  [  1000 /   2000] (Dec)
 2  Yel Alarm - In/Out  [  1000 /   2000] (Dec)
This Command: cnflnparm 7
Which parameter do you wish to change:

cnflnsigparm (Configure Line Signalling Parameters)

The cnflnsigparm command configures the line signalling parameters.

Attributes

Jobs: No Log: Yes Lock: Yes Node Type: IPX, IGX

Associated Commands

cnflnparm, cnflnstats, dsplnstatcnf, dsplnstathist, upln, dnln, cnfln

Syntax

Function

The cnflnsigparm command configures the line signalling parameters associated with a line. When you enter cnflnsigparm, the screen displays the parameters, as shown in Figure 1-24:

cc2            LAN   StrataCom       IPX 32    8.5     Aug. 30 1997 11:16 PST
1  CDP & CIP Heartbeat                    [   2] (sec)
2  CDP & CIP Sig. Polling Rate            [  10] (sec)
3  CDP & CIP Default Inband Sig Delay     [  96] (msec)
4  CDP & CIP Default Inband Playout Delay [ 200] (msec)
5  CDP & CIP Default Pulse Sig Delay      [  96] (msec)
6  CDP & CIP Default Pulse Playout Delay  [ 200] (msec)
7  CIP Number of Packet Slices            [   1]
8  CDP & CIP Packet Rate                  [ 200] (pkt/sec)
9  CDP & CIP Condition CCS Lines?         [ YES]
10 CIP Default Inband Min. Wink           [ 140] (msec)
11 CIP Default Pulse Min. Wink            [ 140] (msec)
This Command: cnflnsigparm
Which parameter do you wish to change

cnflnstats (Configure Line Statistics Collection)

The cnflnstats command configures statistics collection for the specified line.

Attributes

Jobs: Yes Log: Yes Lock: Yes Node Type: IPX, IGX, BPX

Associated Commands

dsplnstatcnf, dsplnstathist

Syntax

Function

This command configures parameters for line statistic collection. Primarily, cnflnstats is a debug tool and should not be necessary for regular use. It lets you customize statistics collected on each line. Table 1-11 lists the statistics by type.

Not all statistic types are available for all lines. Only valid statistics are displayed for the user to select from, the others appear in gray.

Figure 1-25 illustrates the screen displayed after entering cnflnstats.

cc2            LAN   StrataCom       IPX 32    8.5     Aug. 30 1997 11:20 PST
Line Statistic Types
 1) Bipolar Violations
 2) Frames Slips
 3) Out of Frames
 4) Losses of Signal
 5) Frames Bit Errors
 6) CRC Errors
 7) Out of Multi-Frames
 8) All Ones in Timeslot 16
Last Command: cnflnstats 15 6 255 e
Next Command:

cnfmxbutil (Configure MUXBUS Utilization)

The cnfmxbutil command configures the MUXBUS or CELLBUS utilization factor for each FRP or FRM, respectively.

Attributes

Jobs: No Log: Yes Lock: Yes Node Type: IPX, IGX

Associated Commands

none

Syntax

Function

The cnfmxbutil command lets you configure the MUXBUS or CELLBUS utilization factor for each FRP or FRM in the node on a slot-by-slot basis. (System software automatically allocates a certain amount of bandwidth for each FRP or FRM in a node. Since the maximum data rate for an FRP or FRM is 2 Mbps, this bandwidth is also the maximum amount of the bus reserved for an FRP or FRM.)

In many applications, each of the four FRP or FRM ports is configured for a large number of 56 or 64 Kbps connections. System software totals the bandwidth required for all the connections, multiplies the total by 121% to reserve extra bandwidth for overhead, then subtracts this amount from the total available bus bandwidth.

However, statistically full utilization is not often required on ports with a large number of connections, so the reserved bus bandwidth may be further reduced. In a node with a T3 or E3 ATM trunk card, much of the bus bandwidth may be assigned to the ATM trunk, so you should exercise caution when allocating the remaining bus bandwidth.

See Figure 1-26 for a sample screen. The screen displays "N/A" for a slot where no FRP or FRM exists. Once the slot is selected, the system displays the message "Enter Utilization Factor." The range is 1-250%. The default is 121%. The extra 21% for the default is for the overhead for encapsulating the Frame Relay frame into the FastPackets or ATM cells.

gamma     SV+     SuperUser      IPX32     Rev:  8.5      Aug. 14 1997  14:27 PDT 
                                                                               
                                                          
                                                                                
 
      Slot  1: N/A      Slot 9:  N/A     Slot 17: 121%     Slot 25: N/A
      Slot  2: N/A      Slot 10: N/A     Slot 18: 121%     Slot 26: N/A
      Slot  3: N/A      Slot 11: N/A     Slot 19: N/A      Slot 27: N/A
      Slot  4: N/A      Slot 12: N/A     Slot 20: N/A      Slot 28: N/A 
      Slot  5: N/A      Slot 13: N/A     Slot 21: N/A      Slot 29: N/A 
      Slot  6: N/A      Slot 14: N/A     Slot 22: N/A      Slot 30: N/A
      Slot  7: N/A      Slot 15: N/A     Slot 23: N/A      Slot 31: N/A 
      Slot  8: N/A      Slot 16: N/A     Slot 24: N/A      Slot 32: N/A
This Command: cnfmxbutil                                                          
Enter Slot:

cnfnodeparm (Configure Node Parameter)

Sets a variety of general parameters for the nodes in a network.

Attributes

Jobs: No Log: Yes Lock: Yes Node Type: IPX, IGX, BPX

Associated Commands

none

Syntax

Function

The cnfnodeparm command lets you change some of the node's system parameters. The parameters you can set with cnfnodeparm are not closely related. Table 1-11 and Table 1-12 describe the parameters for the IPX/IGX and BPX nodes, respectively. After each table, an applicable set of cnfnodeparm screens appears. The defaults for the parameters are selected by Cisco engineering to operate under normal network conditions. With few exceptions, you should change them only with the guidance of the Cisco TAC.

Figure 1-27 shows the available parameters on an IPX or IGX node.

pubsipx1       TN    StrataCom       IPX 16    8.5 May  9 1997  09:30 GMT 
 
1  Update Initial Delay   [ 5000] (D)   16 CC Redundancy Cnfged   [    Y] (Y/N)
2  Update Per-Node Delay  [30000] (D)   17 MT3 Pass Through Relay [    Y] (Y/N)
3  Comm-Break Test Delay  [30000] (D)   18 Nw Pkt Tx Rate (pps)   [  500] (D)
4  Comm-Break Test Offset [   10] (D)   19 Stats Memory (x 10KB)  [   61] (D)
5  Network Timeout Period [ 1700] (D)   20 Standby Update Timer   [    1] (D)
6  Network Inter-p Period [ 4000] (D)   21 Stby Updts Per Pass    [   30] (D)
7  NW Sliding Window Size [    1] (D)   22 Gateway ID Timer       [   30] (D)
8  Num Normal Timeouts    [    7] (D)   23 GLCON Alloc Timer      [   30] (D)
9  Num Inter-p Timeouts   [    3] (D)   24 Comm Fail Delay        [   60] (D)
10 Num Satellite Timeouts [    6] (D)   25 Nw Hdlr Timer (msec)   [  100] (D)
11 Num Blind Timeouts     [    4] (D)   26 CBUS Delay (msec)      [   20] (D)
12 Num CB Msg Timeouts    [    2] (D)   27 SNMP Event logging     [    Y] (Y/N)
13 Comm Fail Interval     [10000] (D)   28 TFTP Grant Delay (sec) [    1] (D)
14 Comm Fail Multiplier   [    3] (D)   29 TFTP ACK Timeout (sec) [   10] (D)
15 Temperature Threshold  [   50] (D)   30 TFTP Write Retries     [    3] (D)
                                                                                
This Command: cnfnodeparm
 
 
Continue? y
pubsipx1       TN    StrataCom       IPX 16    8.5 May  9 1997  09:31 GMT 
 
31 FRP Link Status Alarm  [    Y] (Y/N)
32 Job Lock Timeout       [    0] (D)
33 Max Via LCONs          [ 5000] (D)
34 Max Blind Segment Size [ 3570] (D)
35 Max Nib Xmit Msgs      [ 1000] (D)
36 Max Stby Update Q Sz   [ 5000] (D)
 
 
 
 
                                                                                
This Command: cnfnodeparm  
 
 
Enter parameter index: 

Figure 1-28 shows the available parameters on a BPX node.

sw45           TN    StrataCom       BPX 15    8.5 Aug. 27 1997 18:25 PDT 
 
1  Update Initial Delay   [ 5000] (D)   16 Stats Memory (x 10KB)  [   61] (D)   
2  Update Per-Node Delay  [30000] (D)   17 Standby Update Timer   [   10] (D)   
3  Comm-Break Test Delay  [30000] (D)   18 Stby Updts Per Pass    [   50] (D)   
4  Comm-Break Test Offset [   10] (D)   19 Gateway ID Timer       [   30] (D)   
5  Network Timeout Period [ 1700] (D)   20 GLCON Alloc Timer      [   30] (D)   
6  Network Inter-p Period [ 4000] (D)   21 Comm Fail Delay        [   60] (D)   
7  NW Sliding Window Size [    1] (D)   22 Nw Hdlr Timer (msec)   [   50] (D)   
8  Num Normal Timeouts    [    7] (D)   23 SAR CC Transmit Rate   [  560] (D)   
9  Num Inter-p Timeouts   [    3] (D)   24 SAR High Transmit Rate [  280] (D)   
10 Num Satellite Timeouts [    6] (D)   25 SAR Low Transmit Rate  [   56] (D)   
11 Num Blind Timeouts     [    4] (D)   26 SAR VRAM Cngestn Limit [ 7680] (D)   
12 Num CB Msg Timeouts    [    5] (D)   27 SAR VRAM Cell Discard  [  256] (D)   
13 Comm Fail Interval     [10000] (D)   28 ASM Card Cnfged        [    Y] (Y/N)
14 Comm Fail Multiplier   [    3] (D)   29 TFTP Grant Delay (sec) [    1] (D)   
15 CC Redundancy Cnfged   [    N] (Y/N) 30 TFTP ACK Timeout (sec) [   10] (D)   
                                                                                
This Command: cnfnodeparm
 
 
Continue? y
sw45           TN    StrataCom       BPX 15    8.5 Aug. 27 1997 18:26 PDT 
 
31 TFTP Write Retries     [    3] (D)   
32 SNMP Event logging     [    Y] (Y/N)
33 Job Lock Timeout       [   60] (D)   
34 Max Via LCONs          [50000] (D)   
35 Max Blind Segment Size [ 3570] (D)   
36 Max XmtMemBlks per NIB [ 3000] (D)   
37 Max Stby Update Q Sz   [ 5000] (D)   
 
 
 
 
 
 
 
 
                                                                                
This Command: cnfnodeparm  
 
 
Enter parameter index: 

cnfnwip (Configure Network IP Address)

The cnfnwip command configures an IP address and subnet mask for the node.

Attributes

Jobs: No Log: Yes Lock: Yes Node Type: IPX, IGX, BPX

Associated Commands

none

Syntax

An example of this command is:

cnfnwip 199.35.96.217 255.255.255.0

where 199.35.96.217 is the IP address, and 255.255.255.0 is the subnet mask.

Function

The network IP address and subnet mask support statistics collection for StrataView Plus. The cnfnwip command defines the IP address the system uses to pass messages between StrataView Plus and the node. The Statistics Master process in StrataView Plus Network collects statistics. The Statistics Manager requests and receives statistics using TFTP Get and Put messages. These TFTP messages pass between the node and the Statistics Master using IP Relay. (See the cnfstatmast description for details on setting the Statistics Master address.) For an example of the cnfnwip command, refer to the screen in Figure 1-29.

axiom       TN    Bootzilla       IGX 32    8.5       Aug. 5 1997  18:25 GMT
Active Network IP Address:             169.134.90.106
Active Network IP Subnet Mask:         255.255.255.0
Last Command: cnfnwip 169.134.90.106 255.255.255.0
Next Command:

cnfportstats (Configure Frame Relay Port Statistics Collection)

The cnfportstats command configures parameters for Frame Relay ports.

Attributes

Jobs: Yes Log: Yes Lock: Yes Node Type: IPX, IGX, BPX

Associated Commands

none

Syntax

Function

The cnfportstats command configures Frame Relay port parameters. The primarily purpose of this command is debugging. Table 1-14 lists the configurable statistics. Not all statistic types are apply to all ports. Refer to Figure 1-30 and Figure 1-31 for examples.

Figure 1-31 shows that the selected statistic is 33--the number of transmitted bytes while the ingress LMI is showing a failed condition. After the port number and statistic number (33) on the command line, the remaining parameters are the interval, enable for this statistic, number of samples, and so on.

pubsigx1       TN    StrataCom       IGX 32    8.5       Aug. 5 1997  17:21 GMT
Port Statistic Types
 1) Frames Received                 14) LMI UNI Status Update Count
 2) Frames Transmitted              15) LMI Invalid Status Enquiries
 3) Bytes Received                  16) LMI UNI Link Timeout Errors
 4) Bytes Transmitted               17) LMI UNI Keepalive Sequence Errors
 5) Frames Transmitted with FECN 18) Receive Frames Undefined DLCI Count
 6) Frames Transmitted with BECN    19) DE Frames Dropped
 7) Receive Frame CRC Errors        20) LMI NNI Status Enquiries
 8) Invalid Format Receive Frames   21) LMI NNI Status Receive Count
 9) Receive Frame Alignment Errors  22) LMI NNI Status Update Count
10) Illegal Length Receive Frames   23) LMI NNI Link Timeout Errors
11) Number of DMA Overruns          24) LMI NNI Keepalive Sequence Errors
12) LMI UNI Status Enquiries        25) CLLM Frames Transmitted
13) LMI UNI Status Transmit Count   26) CLLM Bytes Transmitted
This Command: cnfportstats 3.1
Continue?

pubsigx1       TN    StrataCom       IGX 32    8.5       Aug. 5 1997  17:24 GMT
Port Statistic Types
27) CLLM Frames Received
28) CLLM Bytes Received
29) CLLM Failures
30) Tx Frames Discarded - Queue Overflow
31) Tx Bytes Discarded - Queue Overflow
32) Tx Frames while Ingress LMI Failure
33) Tx Bytes while Ingress LMI Failure
Last Command: cnfportstats 3.1 33 2 e 2 4 y
Next Command:

cnfrobparm (Configure Robust Alarms Parameters)

The cnfrobparm command sets parameters associated with the Robust Alarms feature.

Attributes

Jobs: No Log: No Lock: Yes Node Type: IPX, IGX, BPX

Associated Commands

none

Syntax

Function

This command sets Robust Alarms parameters. Robust Alarms is a protocol for node-to-Network Management System (NMS) communications. When a node has statistics or alarm information for the NMS, it requires a confirmation from the NMS of database update. Table 1-14 lists the parameters. Figure 1-32 illustrates the command.

D1.a34         TRM   SuperUser       IPX 16    8.5     Aug. 14 1997 15:02 PDT 
                                                                                
                           Robust Parameters 
                                                                                
1  Robust State wakeup timer (sec) ..................................				10 
2  Robust update timer (sec) ........................................				10 
3  Robust acknowledge timeout (sec) .................................600
4  Robust acknowledge reset timeout (sec) ...........................60
                                                                                
                                                                                
                                                                                
                                                                                
                                                                                
                                                                                
                                                                                
                                                                                
                                                                                
                                                                                
This Command: cnfrobparm                                                        
                                                                                
                                                                                
Which parameter do you wish to change:                                          
                                                                                

cnfslotstats (Configure Slot Statistics Collection)

The cnfslotstats command configures the collection of statistics for the selected node slot.

Attributes

Jobs: Yes Log: Yes Lock: Yes Node Type: BPX

Associated Commands

dspsloterrs

Syntax

Function

This command sets the collection interval for each of the BPX node slot statistics. The default is for no statistics to be collected. The collection interval range is 1 minute-255 minutes (4 1/4 hours).

Table 1-15 lists the nine statistics associated with each slot in the BPX node. Figure 1-33 illustrates the command screen. This command is primarily a troubleshooting tool for use when hardware errors are experienced that may not be detected by the individual care self-test routines. An associated display command (dspsloterrs) is available for all users.

sw81           TN    StrataCom       BPX 15    8.5    Aug. 1 1997  15:42 PST
Card Statistics Types
 1) Standby PRBS Errors
 2) Rx Invalid Port Errs
 3) PollA Parity Errors
 4) PollB Parity Errors
 5) Bad Grant Errors
 6) Tx Bip 16 Errors
 7) Rx Bip 16 Errors
 8) Bframe parity Errors
 9) SIU phase Errors
10) Rx FIFO Sync Errors
11) Poll Clk Errors
12) CK 192 Errors
This Command: cnfslotstats 8

cnftcpparm (Configure TCP Parameters)

The cnftcpparm command configures the TCP parameter.

Attributes

Jobs: Yes Log: Yes Lock: Yes Node Type: IPX, IGX, BPX

Associated Commands

dsptcpparm

Syntax

Function

This command specifies the number of times per second that the BCC checks the IP addressees for attention requests. Figure 1-34 illustrates the system response when you enter cnftcpparm:

sw81           TN    StrataCom       BPX 15    8.5    Aug. 1 1997  15:46 PST
NWIP Bandwidth Throttle (Kbytes/sec):  32
This Command: cnftcpparm
Enter NWIP Bandwidth Throttle (Kbytes/sec):

cnftermfunc

Configures port functions for the IPX, IGX, or BPX control and auxiliary ports. The IPX and IGX nodes support two EIA/TIA-232 asynchronous serial ports on the SCC and SCM, respectively. The BPX node supports two EIA/TIA-232 asynchronous serial ports on the LMBCC. In all cases, the top port is the CONTROL TERMINAL port, and the lower port is the AUX PORT. The CONTROL TERMINAL port can connect to a control terminal, StrataView Plus, a direct dial-in modem, or any external EIA/TIA-232 device. The AUX PORT can connect to a printer, an auto-dial modem to call a control center, or an external EIA/TIA-232 device.

The interface specified for the port must match the equipment physically attached to the port. The baud rate and other data transmission parameters for the port are set with the cnfterm command. If either port is configured as an external device window, enter the window command to begin a session with the external device.

If the auxiliary port is configured as an autodial modem, designate a "network ID" and a "phone number". Configuring the auxiliary port for an autodial modem enables the following to occur: When a change in alarm status happens anywhere in the network, the autodial modem attached to the auxiliary port dials the specified "phone number." If the call goes to the TAC, the alarm is logged under the specified "network ID." With this log, Cisco engineers are automatically notified of any problems that occur in the network.

Full Name

Configure terminal port functions

Syntax

cnftermfunc <a/c> <index> [escape_string | (Network_ID Dial_String)]

Related Commands

cnfterm, cnfprt, dsptermfunc

Attributes

Example 1

cnftermfunc

Description

Configure an IPX, IGX, or BPX node control or auxiliary port.

System Response

Without an argument on the command line, the switch displays a list of parameters. Figure 1-35 shows the screen on an IPX node.

beta           TRM   YourID:1        IPX 32  8.5    Mar. 15 1997 14:46 MST 
                                                                                
                                                                                
Control port		Auxiliary port                           
1.VT100/StrataView		1.Okidata 182 Printer
2.VT100	       	2.Okidata 182 Printer with LOG 
3.External Device Window		3.Alarm Message Collector               
4.External Device Window                
5.Autodial Modem                        
6.VT100                                 
                                                                                
                                                                                
                                                                                
                                                                                
Last Command: cnftermfunc                                                       
                                                                                
                                                                                
Next Command:                                                                                        
                                                                                

Example 2

cnftermfunc a Intrepid 18007674479

Description

Configure an auxiliary port. The port configuration screen appears with "Autodial Modem" highlighted to indicate that this interface has been chosen for the auxiliary port. When an alarm occurs on the network, the modem dials 18007674479 to reach the TAC. The alarm is logged on a Cisco computer under the name "Intrepid."

cnftlparm (Configure Trunk-Based Loading Parameters)

The cnftlparm command configures the trunk based loading (TBL) parameters.

Attributes

Jobs: No Log: Yes Lock: Yes Node Type: IPX, IGX, BPX

Associated Commands

cnfcmparm

Syntax

Parameters

Table 1-20 describes the cnftlparm parameters.

Function

The cnftlparm command lets you control the rate of update messages in conjunction with trunk-based loading. For descriptions of the trunk-based loading parameters, refer to Table 1-20.

Figure 1-36 shows the screen for cnftlparm.

sw66           TN    StrataCom       BPX 15    8.5 Aug. 27 1997 22:31 GMT 
 
1  Enable                   [  Yes]
2  Normal Interval          [  150] (100msecs)   
3  Fast Interval            [   50] (100msecs)   
4  Low Threshold            [   50] (D)   
5  High Threshold           [   90] (D)   
6  Min Percent Chg, Mid 1   [   10] (D)   
7  Min Percent Chg, Mid 2   [    6] (D)   
8  Min Percent Chg, Mid 3   [    3] (D)   
9  Min Percent Chg, Upper   [    2] (D)   
10 Background Updt Count    [    0] (D)   
11 Update Algorithm         [    0] (D)   
 
 
 
 
                                                                                
This Command: cnftlparm  
 
 
Enter parameter index: 

cnftrkparm (Configure Trunk Card Parameter)

The cnftrkparm command sets specified trunk parameters for the following front cards:

• ALM/B

• AIT

• BTM

• NTC

• NTM

• BNI

• BXM

Attributes

Jobs: No Log: Yes Lock: Yes Node Type: IPX, IGX, BPX

Associated Commands

dsptrkstathist, dsptrkstatcnf

Syntax

Function

Use the cnftrkparm command to optimize a network for particular traffic mixes. This command configures any of the trunk-specific parameters associated with a trunk card. It applies to either a FastPacket trunk or an ATM trunk. For ATM trunks, cnftrkparm applies to both physical and virtual trunks. Spacer queues indicated for the CLP and EFCN thresholds pertain to AIT and BTM cards in an IPX node or IGX node, respectively.

This command can also reconfigure trunk queue depths to meet the CEPT requirement for a maximum end-to-end delay of 10 milliseconds. For this purpose, enter the following:

cnftrkparm <trunk number> <parameter index> <parameter value>

where: trunk number specifies the trunk.
parameter index is 2 (which corresponds to the NTS queue).
parameter value is 7 (which is the maximum allowable queue depth).

When the system receives this command and a trunk number, it displays the configurable parameters with an index number for each. The parameters vary with the trunk type, as the subsequent figures and tables show. Table 1-21, Table 1-22, and Table 1-23 list the parameters for trunks carrying FastPackets and ATM cells on different platforms as well as virtual trunks. Figure 1-37, Figure 1-38, Figure 1-39, and Figure 1-40 show the response when you specify a FastPacket line or trunk on a variety of platforms. A table follows one or two screen examples.

sw83           TN    StrataCom       IPX 16    8.5       Aug. 23 1997 15:58 PST
PLN 13 Parameters:
 1 Yel Alm-In/Out (D) [   600/   600]      18 Red Alm-In/Out (D) [  2500/ 15000]
 2 Rx Max Age - Voice    (D)   [ N/A]      19 Tx Max Age - Voice    (D)   [  20]
 3 Rx EFCN  - BdataB     (D)   [ N/A]      20 Tx EFCN    - BdataB   (D)   [  30]
 4 Gateway Efficiency    (D)   [ N/A]
 5 EFCN     - Rx Space   (D)   [ N/A]      Tx Age Step2 (D)     Tx Age Step  (D)
 6 Low CLP  - Rx_Space   (%)   [ N/A]      21 BDataA [ 128]     23 BDataA [ 128]
 7 High CLP - Rx_Space   (%)   [ N/A]      22 BDataB [ 128]     24 BDataB [ 128]
Rx High CLP  (%)     Rx Low CLP   (%)      Tx High CLP  (%)     Tx Low CLP   (%)
 8 BDataA [ N/A]     10 BDataA [ N/A]      25 BDataA [ 100]     27 BDataA [ 100]
 9 BDataB [ N/A]     11 BdataB [ N/A]      26 BDataB [  75]     28 BDataB [  25]
Receive Queue Depth               (D)      Transmit Queue Depth              (D)
12 Voice  [ N/A]     15 BDataA [ N/A]      29 Voice  [  22]     32 BDataA [ 301]
13 Non TS [ N/A]     16 BDataB [ N/A]      30 Non TS [ 114]     33 BDataB [ 301]
14 TS     [ N/A]     17 HighPri[ N/A]      31 TS     [2616]     34 HighPri[ 100]
Last Command: cnftrkparm 13
Next Command:

pubsbpx1       TN    StrataCom       BPX 15    8.5 July 15 1997 09:37 GMT 
 
TRK 1.1 Parameters
 1 Q Depth - Voice     [  242] (Dec)    15 Q Depth  - CBR      [  600] (Dec)
 2 Q Depth - Non-TS    [  360] (Dec)    16 Q Depth  - VBR      [ 1000] (Dec)
 3 Q Depth - TS        [ 1000] (Dec)    17 Q Depth  - ABR      [ 9070] (Dec)
 4 Q Depth - BData A   [ 1000] (Dec)    18 Low  CLP - CBR      [ 100] (%)
 5 Q Depth - BData B   [ 8000] (Dec)    19 High CLP - CBR      [ 100] (%)
 6 Q Depth - High Pri  [ 1000] (Dec)    20 Low  CLP - VBR      [ 100] (%)
 7 Max Age - Voice     [   20] (Dec)    21 High CLP - VBR      [ 100] (%)
 8 Red Alm - I/O (Dec) [  2500 / 15000] 22 Low  CLP - ABR      [  25] (%)
 9 Yel Alm - I/O (Dec) [  2500 / 15000] 23 High CLP - ABR      [  75] (%)
10 Low  CLP - BData A  [ 100] (%)       24 EFCN     - ABR      [  30] (Dec)
11 High CLP - BData A  [ 100] (%)       25 SVC Queue Pool Size [  144] (Dec)
12 Low  CLP - BData B  [  25] (%)
13 High CLP - BData B  [  75] (%)
14 EFCN     - BData B  [  30] (Dec)
                                                                                
This Command: cnftrkparm 1.1  
 
 
Which parameter do you wish to change: 

sw97           TRM   StrataCom       BPX 15    8.5 Apr. 30 1997 13:14 GMT 
 
TRK 13.1 Parameters
Trunk Type:        NNI
 1 Q Depth - Voice 	[3000] (Dec) 	15 Q Depth  - CBR      [  1200] (Dec)
 2 Q Depth - Non-TS    [  3000] (Dec)   16 Q Depth  - VBR      [ 10000] (Dec)
 3 Q Depth - TS        [ 1000] (Dec)    17 Q Depth  - ABR      [ 30000] (Dec)
 4 Q Depth - BData A   [ 20000] (Dec)   18 Low  CLP - CBR      [ 100] (%)
 5 Q Depth - BData B   [ 20000] (Dec)   19 High CLP - CBR      [ 100] (%)
 6 Q Depth - High Pri  [ 1000] (Dec)    20 Low  CLP - VBR      [ 100] (%)
 7 Max Age - Voice     [   20] (Dec)    21 High CLP - VBR      [ 100] (%)
 8 Red Alm - I/O (Dec) [  2500 / 15000] 22 Low  CLP - ABR      [  25] (%)
 9 Yel Alm - I/O (Dec) [  2500 / 15000] 23 High CLP - ABR      [  75] (%)
10 Low  CLP - BData A  [ 100] (%)       24 EFCN     - ABR      [  30] (Dec)
11 High CLP - BData A  [ 100] (%) 	25 SVC Queue Pool Size [  144] (Dec)
12 Low  CLP - BData B  [  25] (%)
13 High CLP - BData B  [  75] (%)
14 EFCN     - BData B  [  30] (Dec)
                                                                                
Last Command: cnftrkparm 13.1
 
 
Next Command:

sw97           TN    StrataCom       BPX 15    8.5       Aug. 9 1997  10:11 GMT
TRK 1.1.1 Parameters
 8 Red Alm - I/O (Dec) [  2500 /  10000]
 9 Yel Alm - I/O (Dec) [  2500 /  10000]
15 Q Depth  - CBR      [ 2678] (Dec)
18 Low  CLP - CBR      [ 100] (%)
19 High CLP - CBR      [ 100] (%)
This Command: cnftrkparm 1.1.1
Which parameter do you wish to change:

cnftrkstats (Configure Trunk Statistics Collection)

The cnftrkstats command configures collection of statistics for a selected trunk.

Attributes

Jobs: Yes Log: Yes Lock: Yes Node Type: IPX, IGX, BPX

Associated Commands

dsptrkstatcnf, dsptrkstathist

Syntax

Function

The cnftrkstats command is primarily a debug command. It configures the collection of statistics for a physical or virtual trunk. After displaying all statistic types for the trunk, the system prompts for "statistic type." Enter the index number associated with the statistic.

Not all types of statistics are available for all lines. Unavailable selections appear in half-tone. Table 1-24 lists the types of statistics that are configurable for FastPacket T1 trunks and ATM T3 trunks. The subsequent figures show the screens associated with T1 packet trunks and T3 ATM trunks.

Figure 1-41 is the only screen for T1 trunks.

sw83           TN    StrataCom       IPX 16    8.5       Aug. 1 1997  14:42 PST

Line Statistic Types
 1) Bipolar Violations                  18) Voice Packets Transmitted
 3) Out of Frames                       19) TS Packets Transmitted
 4) Losses of Signal                    20) NTS Packets Transmitted
 5) Frames Bit Errors                   21) CC Packets Transmitted
 6) CRC Errors                          22) BDA Packets Transmitted
 9) Packet Out of Frames                23) BDB Packets Transmitted
10) Packet CRC Errors                   24) Total Packets Transmitted
12) Tx Voice Packets Dropped            25) BDA CLP Packets Dropped
13) Tx TS Packets Dropped               26) BDB CLP Packets Dropped
14) Tx NTS Packets Dropped              27) BDA EFCN Pkts Transmitted
15) Tx CC Packets Dropped               28) BDB EFCN Pkts Transmitted
16) Tx BDA Packets Dropped              149) Bdata A CLP Packets Tx to Line
17) Tx BDB Packets Dropped              150) Bdata B CLP Packets Tx to Line
Last Command: cnftrkstats 13
Next Command:

The following screens, shown in Figure 1-42 through Figure 1-48, pertain to an ATM trunk (AIT card) on an IPX node. Other trunk types and cards have other parameters. To see the list of these, enter the command and continue from page to page without entering an index number.

sw83           TN    StrataCom       IPX 16    8.5       Aug. 1 1997  14:45 PST
Line Statistic Types
 3) Out of Frames                       22) BDA Packets Transmitted
 4) Losses of Signal                    23) BDB Packets Transmitted
10) Packet CRC Errors                   24) Total Packets Transmitted
12) Tx Voice Packets Dropped            25) BDA CLP Packets Dropped
13) Tx TS Packets Dropped               26) BDB CLP Packets Dropped
14) Tx NTS Packets Dropped              27) BDA EFCN Pkts Transmitted
15) Tx CC Packets Dropped               28) BDB EFCN Pkts Transmitted
16) Tx BDA Packets Dropped              29) Line Code Violations
17) Tx BDB Packets Dropped              30) Line Errored Seconds
18) Voice Packets Transmitted           31) Line Severely Err Secs
19) TS Packets Transmitted              32) Line Parity Errors
20) NTS Packets Transmitted             33) Errored Seconds - Line
21) CC Packets Transmitted              34) Severely Err Secs - Line
This Command: cnftrkstats 11
Continue?

sw83           TN    StrataCom       IPX 16    8.5       Aug. 1 1997  14:46 PST
Line Statistic Types
35) Path Parity Errors                  48) Tx Voice Cells Drpd
36) Errored Secs - Path                 49) Tx TimeStamped Cells Drpd
37) Severely Err Secs - Path            50) Tx NTS Cells Dropped
38) Severely Err Frame Secs             51) Tx Hi-Pri Cells Drpd
39) AIS Signal Seconds                  52) Tx BData A Cells Drpd
40) Unavail. Seconds                    53) Tx BData B Cells Drpd
41) BIP-8 Code Violations               54) Voice Cells Tx to line
42) Cell Framing Errored Seconds        55) TimeStamped Cells Tx to ln
43) Cell Framing Sev. Err Secs.         56) NTS Cells Tx to line
44) Cell Framing Sec. Err Frame Secs    57) Hi-Pri Cells Tx to line
45) Cell Framing Unavail. Secs.         58) BData A Cells Tx to line
46) ATM Cell Header HEC Errs            59) BData B Cells Tx to line
47) Pkts. Rx from Muxbus                60) Half Full cells Tx to ln
This Command: cnftrkstats 11
Continue?

sw83           TN    StrataCom       IPX 16    8.5      Aug. 1 1997  14:47 PST
Line Statistic Types
61) Full cells Tx to ln                 74) Rx Hi-pri Pkts Dropped
62) Total Cells Tx to line              75) Rx BDA Pkts Dropped
63) Tx Bdata A CLP Cells Drpd           76) Rx BDB Pkts Dropped
64) Tx Bdata B CLP Cells Drpd           77) Voice pkts Tx to Muxbus
65) Bdata A EFCN Cells Tx ln            78) TS pkts Tx to Muxbus
66) Bdata B EFCN Cells Tx ln            79) NTS pkts Tx to Muxbus
67) Half Full Cells Rx from ln          80) Hi-pri pkts Tx to Muxbus
68) Full Cells Rx from line             81) Bdata A pkts Tx to Muxbus
69) Total Cells Rx from line            82) Bdata B pkts Tx to Muxbus
70) Total pkts Rx from line             83) Rx Bdata A CLP pkts drpd
71) Rx Voice Pkts Dropped               84) Rx Bdata B CLP pkts drpd
72) Rx TS Pkts Dropped                  85) Bdata A EFCN Pkts Tx muxbus
73) Rx NTS Pkts Dropped                 86) Bdata B EFCN Pkts Tx muxbus
This Command: cnftrkstats 11
Continue?

sw83           TN    StrataCom       IPX 16    8.5     Aug. 1 1997  14:48 PST
Line Statistic Types
87) Total Pkts Tx to muxbus             100) Rx Spacer 2 Pkts dropped
88) Rx voice cells drpd                 101) Rx Spacer 3 Pkts dropped
89) Rx TimeStamped Cells drpd           102) Rx Spacer 4 Pkts dropped
90) Rx NTS Cells dropped                103) Rx Spacer 5 Pkts dropped
91) Rx Hi-pri Cells dropped             104) Rx Spacer 6 Pkts dropped
92) Rx Bdata A Cells dropped            105) Rx Spacer 7 Pkts dropped
93) Rx Bdata B Cells dropped            106) Rx Spacer 8 Pkts dropped
94) Rx Bdata A CLP cells drpd           107) Rx Spacer 9 Pkts dropped
95) Rx Bdata B CLP cells drpd           108) Rx Spacer 10 Pkts dropped
96) Rx Spacer CLP Pkts drpd             109) Rx Spacer 11 Pkts dropped
97) Spacer EFCN Pkts Tx to Muxbus       110) Rx Spacer 12 Pkts dropped
98) Frame Sync Errors                   111) Rx Spacer 13 Pkts dropped
99) Rx Spacer 1 Pkts dropped            112) Rx Spacer 14 Pkts dropped
This Command: cnftrkstats 11

sw83           TN    StrataCom       IPX 16    8.5      Aug. 1 1997  14:49 PST
Line Statistic Types
113) Rx Spacer 15 Pkts dropped          126) Spacer 10 Pkts Tx to Muxbus
114) Rx Spacer 16 Pkts dropped          127) Spacer 11 Pkts Tx to Muxbus
115) Rx Spacer Pkts drpd                128) Spacer 12 Pkts Tx to Muxbus
116) Spacer 0 Pkts Tx to Muxbus         129) Spacer 13 Pkts Tx to Muxbus
117) Spacer 1 Pkts Tx to Muxbus         130) Spacer 14 Pkts Tx to Muxbus
118) Spacer 2 Pkts Tx to Muxbus         131) Spacer 15 Pkts Tx to Muxbus
119) Spacer 3 Pkts Tx to Muxbus         132) Spacer 16 Pkts Tx to Muxbus
120) Spacer 4 Pkts Tx to Muxbus         133) Rx Voice QSE Cells Tx
121) Spacer 5 Pkts Tx to Muxbus         134) Rx Time Stamped QSE Cells Tx
122) Spacer 6 Pkts Tx to Muxbus         135) Rx NTS QSE Cells Tx
123) Spacer 7 Pkts Tx to Muxbus         136) Rx Hi Priority QSE Cells Tx
124) Spacer 8 Pkts Tx to Muxbus         137) Rx BData A QSE Cells Tx
125) Spacer 9 Pkts Tx to Muxbus         138) Rx Bdata B QSE Cells Tx
This Command: cnftrkstats 11

sw83           TN    StrataCom       IPX 16    8.5       Aug. 1 1997  15:02 PST
Line Statistic Types
139) Rx BData A EFCN QSE Cells Tx       152) Cell Framing Yel Transitions
140) Rx BData B EFCN QSE Cells Tx       153) AIS Transition Count
141) FEBE Counts                        161) CGW Packets Rx From IPX Net
142) FERR Counts (M or F bit)           162) CGW Cells Tx to Line
143) Cell Framing FEBE Err Secs         163) CGW Frms Relayed to Line
144) Cell Framing FEBE Sev. Err. Secs.  164) CGW Aborted Frames Tx to Line
145) Cell Framing FEBE Counts           165) CGW Dscd Pkts From Abted Frms
146) Cell Framing FE Counts             166) CGW 0-Lngth Frms Rx from Line
147) ATM CRC Errored Seconds            167) CGW Packets Tx to IPX Net
148) ATM CRC Severely Err. Secs.        168) CGW Cells Rx from Line
149) Bdata A CLP Packets Tx to Line     169) CGW Frms Relayed from Line
150) Bdata B CLP Packets Tx to Line     170) CGW Aborted Frms Rx From Line
151) Yellow Alarm Transition Count      171) CGW Dscd Cells From Abted Frms
This Command: cnftrkstats 11

sw83           TN    StrataCom       IPX 16    8.5       Aug. 1 1997  14:51 PST
Line Statistic Types
172) CGW Bd CRC32 Frms Rx from Line     185) OAM Valid OAM Cells Rx
173) CGW Bd Lngth Frms Rx from Line     186) OAM Loopback Cells Rx
174) CGW Bd CRC16 Frms Rx from IPX      187) OAM AIS Cells Rx
175) CGW Bd Length Frms Rx from IPX     188) OAM FERF Cells Rx
176) CGW 0-Length Frms Rx from IPX      189) OAM RTD Cells Rx
177) OAM Valid OAM Cells Tx             190) OAM RA Cells Rx
178) OAM Loopback Cells Tx              191) OAM Invalid OAM Cells Rx
179) OAM AIS Cells Tx                   192) OAM CC Cells Rx
180) OAM FERF Cells Tx
181) OAM RTD Cells Tx
182) OAM RA Cells Tx
183) OAM Invalid Supv Packets Rx
184) OAM CC Cells Tx
This Command: cnftrkstats 11

cnftstparm (Configure Card Self Test Parameters)

The cnftstparm command sets parameters for the internal diagnostic self tests that can be performed for each card type in the node.

Attributes

Jobs: Yes Log: Yes Lock: Yes Node Type: IPX, IGX, BPX

Associated Commands

cnfdiagparm, dspcderrs, prtcderrs, tststats

Syntax

Function

This command sets internal diagnostic, self-test parameters. Upon command entry, the system displays a two-page screen illustrating each of the various card types equipped in the node along with their self test parameters. Each card has two tests: a diagnostic self-test and a background test. The self-test affects the normal operation of the card. The background test can execute while the card is carrying traffic.

The following is a list of the configurable test parameters for each card type:

• Frequency For Test Execution (sec)

• Enable/Disable Self Test (e or d)

• Self Test Failure Increment

• Self Test Failure Threshold

• Timeout For Self Test (sec)

• Enable/Disable Background Test (e or d)

• Background Test Failure Increment

• Background Test Failure Threshold

After cnftstparm is entered, Figure 1-49 shows the first page of the display.

sw45           TN    StrataCom       BPX 15    8.5 Aug. 27 1997 16:04 PDT 
 
Card    Test   - - - - - - Self Test - - - - - - -   - - Background Test - - -
Type    Freq   Enable        Inc   Thresh  Timeout   Enable        Inc   Thresh
----    -----  --------  -------  -------  -------   --------  -------  -------
BCC        90  Enabled       100      300      300   N/A           100      300
ASM       300  Disabled      100      300       60   N/A           100      300
BNI-T3    300  Enabled       100      300      150   N/A           100      300
BNI-E3    300  Enabled       100      300      150   N/A           100      300
ASI-E3    900  Enabled       100      300      800   Enabled       100      300
ASI-T3    900  Enabled       100      300      800   Enabled       100      300
ASI-155   900  Enabled       100      300      800   Enabled       100      300
BNI-155   300  Enabled       100      300      150   N/A           100      300
BXM      2000  Disabled      100      300     1800   Enabled       100      300
 
 
 
                                                                                
Last Command: cnftstparm
 
 
Next Command: 

cnfuiparm (Configure User Interface Parameters)

The cnfuiparm command sets various control terminal user interface parameters.

Attributes

Jobs: No Log: Yes Lock: Yes Node Type: IPX, IGX, BPX

Associated Commands

cnfnodeparm

Syntax

Function

This command lets you set user interface parameters for the control terminal on the local node. It may be necessary to change these parameters in special circumstances, such as when you need to observe a screen for a long period of time or when modem password protection makes logging in difficult. Table 1-25 lists the user interface parameters. Figure 1-50 illustrates the associated display.

sw83 TN    StrataCom       IPX 16    8.5      Aug. 1 1997  17:01 PST
1. Logout Time ........... No Timeout
2. VT Logout Time ........ 4 minutes
3. Prompt Time ........... 60 seconds
4. Command Time .......... 3 minutes
5. UID Privilege Level ... 6
6. Input Character Echo .. Enabled
7. Screen Update Time .... 2 seconds
This Command: cnfuiparm
Enter parameter index:

cnfuvmchparm

Configures default parameters for a channel or range of channels on a UVM. The parameters are:

• Voice codec unit (VCU) level

• PCM interface unit (PIU) level

• VAD threshold

• Modem threshold

See Table 1-26 for an explanation of the preceding UVM channel parameters.

Full Name

Configure UVM channel parameters

Syntax

cnfuvmchparm <channel(s)> <value>

Related Commands

none

Attributes

Example 1

cnfuvmchparm 7.1.1

Description

Configure the parameters for channels 1-23 on port 1 of the UVM in slot 7.

System Response

sw109          VT    StrataCom       IGX 16    8.5 Aug. 26 1997 17:25 PST 
 
From        Parameter: 
             VCU   PIU  VAD   mdm
7.1.1        lvl   lvl  thld  thld   5     6     7     8     9     10    11
7.1.1-23      6     6      40  40     0     0     0     0     0     0     0
7.2.1-23      6     6      40  40     0     0     0     0     0     0     0
 
 
 
 
 
 
 
 
 
 
                                                                                
This Command: cnfuvmchparm 7.1. 
 
 
Enter VCU Noise Level/-10dB [0-15]: 

cnfvchparm (Configure Voice Channel Parameter)

The cnfvchparm command modifies CDP or CVM voice channel parameters.

Attributes

Jobs: Yes Log: Yes Lock: Yes Node Type: IPX, IGX

Associated Commands

cnfcdpparm, dspchan

Syntax

Function

The cnfvchparm command specifies voice card parameters for:

• Voice Activity Detection (VAD)

• Background noise injection

• VF channel loss

• Echo suppression

• Modem detection

Table 1-27 lists the voice parameters you can specify with cnfvchparm. Table 1-28 lists some calculated examples for a sample delay for VAD and non-VAD connections.

Different versions of firmware for the CDP and CVM present different ways of specifying the level of background noise you can select to cover awkward periods of silence at the ends of voice connections. For cards with Model A firmware, you specify the actual level in dBm (deciBels) or dBrnC0. For Model A cards, you can specify the noise levels with a granularity of 0.1 dBm or dBrnC0. For cards with Model B firmware, you enter a number that maps to a noise level. Table 1-29 lists the numbers that correspond to the levels of injected background noise for Model B firmware.

The screen displays in Example 1 and Example 2 illustrate cnfvchparm applied to a Model A CDP and a Model B CDP, respectively. The display for Model A cards shows the deciBel level of the injected noise. The display for the Model B shows the number that corresponds to a deciBel (or dBrnC0) level of background noise.

After you enter cnfvchparm, the system displays "Enter channel(s)." After you enter the parameters, the system requests confirmation by displaying "Reconfigure active CDP channels? (y/n)."

Without the cnfvchparm command, the other ways to re-configure channels are:

• By switching cards

• By deleting then re-adding connections

Example 1 cnfvchparm for Model A

sw110          TN    StrataCom       IGX 16    8.5 Aug. 6 1997  17:43 PDT
CDP Models All                               None               All
UVM Models All                               None               All
           Sample Delay  Bkgnd               Echo Suppression   V.25    Xmit
From 14.1  VAD  Non-VAD  Noise  HPF  Float   Function    Loss   Detect  Delay
14.1-15    A8   01       67     ON   ON      ON          ON     64K     5
14.17-24   A8   01       67     ON   ON      ON          ON     64K     5
This Command: cnfvchparm 14.1-6 A8 1 67 e e e e
V.25 Modem detect, 'd' - disable, '32' - 32K upgrade, '64' - 64K upgrade:

Example 2 cnfvchparm for Model B

sw83 TN    StrataCom       IPX 16    8.5      Aug. 1 1997  17:01 PST
CDP Models All                               None               All
Sample Delay  	Bkgnd 	Echo Suppression	V.25    Xmit
From 11.1  VAD  Non-VAD  Noise  HPF  Float Function Loss Detect  Delay 
11.1-15    A8   01       2      ON   ON      ON		ON	ON		5
11.17-31   A8   01       2      ON   ON      ON		ON	ON	5
This Command: cnfvchparm
Next Command:

cpyfpmap (Copy FastPAD Map Table)

The cpyfpmap command copies the FastPAD map table from one FastPAD port to another.

Attributes

Jobs: No Log: No Lock: Yes Node Type: IPX, IGX

Associated Commands

cnffpmap

Syntax

Function

This command copies a FastPAD map table from one FastPAD port to another FastPAD port. When you enter this command, the system responds as shown in Figure 1-51.

cc7            VT StrataCom       IPX 32    8.5     Aug. 30 1997 10:05 PST
Last Command: 31.2  cc5  31.1
Next Command:

dchst (Display Channel Status)

The dchst command displays CDP or CVM card parameters.

Attributes

Jobs: No Log: No Lock: Yes Node Type: IPX, IGX

Associated Commands

cnfcdpparm

Syntax

Function

This command displays state information for a CDP or CVM channel used for a specific connection. The interval parameter specifies the refresh time for the data. It defaults to 5 seconds. The Transmit and Receive dBm0 for both CDP or CVM indicate the input (towards the circuit line) and output power (from the circuit line) levels for the channel. Modem state indicates whether modem-detect is on or off.

Table 1-30 lists the parameters for the CDP or CVM card. Figure 1-52 illustrates the system display for a CDP or CVM.

alpha            TRM       SuperUser        Rev: 8.5  Aug. 14 1997 16:30 PST
CDP state display for channel 11.1                                    Snapshot 
Transmit dBm0: 
Receive dBm0:
Register 0  =
Register 1  =  
Register 2  =
Register 3  =
Register 4  =
Register 5  =
Register 6  =
Last Command: dchst 11.1 
Next Command:

diagbus (Diagnose Failed Bus)

The diagbus command is used to diagnose a failed IPX MUXBUS.

Attributes

Jobs: No Log: Yes Lock: Yes Node Type: IPX, IGX

Associated Commands

none

Syntax

Function

This command runs detailed diagnostics to isolate MUXBUS problems to a failed card or bus. It is used when a minor alarm is indicated and displaying the alarm (dspalms) screen indicates the message "bus needs diagnosis."

This command can only be run locally with a terminal connected directly to the CONTROL port or remotely from a modem connection. It can not be executed through a VT (virtual terminal) command or when the node's CONTROL port is configured for StrataView mode.

Caution This command may cause a major disruption in service on all lines and connections and should only be run at a time when this can be tolerated.

Performing this test can result in a major disruption in the operation of the node. It should not be performed except as a last resort. To fully isolate the failure may require manual removal of cards, including controller cards etc. For this reason, the command may not be executed over a Virtual Terminal connection.

If the test is successful, and no problems found, the system displays:

Both buses are OK

Otherwise, the system displays various messages to the operator for additional steps to perform in isolating the problem. These messages depend on the results of the diagnostics testing.

drtop (Display Route Op Table)

The drtop command displays the routing table from the local node to each connected remote node.

Attributes

Jobs: No Log: No Lock: No Node Type: IPX, IGX, BPX

Associated Commands

dsptrkcons

Syntax

Function

The drtop command displays the routing table from the local node to each remote node to which it connects. It shows how NPC/B.C. traffic is routed to other nodes in the network. Use drtop to find which trunks are used to send control cells/packets to other nodes.

The display includes remote node name, number of hops to the remote node, the trunk(s) used, and number of satellite hops if any, and the number of unused DS0s (open space) if any on the route. Figure 1-53 illustrates the display.

pubsipx2       VT    StrataCom       IPX 32    8.5      Aug. 2 1997  02:27 GMT
Node Number   Node Name     Hops To  Via Trk  SAT Hops  No HP Hops  Open Space
1             D1.pubsbpx1      2       6         0         0           3
2             D1.pubsigx1      3       6         0         0           3
3             D1.pubsipx2      0       0         0         0           0
5             D1.pubsipx1      1       6         0         0           24
7             D1.pubsipx3      2       6         0         0           24
Last Command: drtop
Next Command:

dspasich (Display ASI Channel Routing Entry)

The dspasich command displays the ATM channel routing entries for an ASI card.

Attributes

Jobs: No Log: No Lock: Yes Node Type: BPX

Associated Commands

None

Syntax

Function

This command displays the routing entries for an ASI card shown in Figure 1-54.

pubsbpx1       VT    StrataCom       BPX 15    8.5       May  24 1997 21:09 GMT
ASI Channel Configuration Query & Display
Slot.port.lcn:5.1.1
Status:       Added        BF hdr: 4145 9002 8012 0501 8640 0000 2DEB
[00] BF tp:   4      [11] VCI:   00000064 [22] UPC CDV: 0      [33] FST up:  0
[01] Pri SDA: 5      [12] Con tp:  VC     [23] UPC CIR: 500    [34] FST dn:  0
[02] Dst Prt: 1      [13] Rmt tp:  ASI    [24] UPC CBS: 1000   [35] FST fdn: 0
[03] Dst lcn: 2      [14] Srv tp:  VBR    [25] UPC IBS: 0      [36] FST rmx: 0
[04] BCF tp:  0      [15] Gen AIS: N      [26] UPC MFS: 200    [37] Q max:64000
[05] Qbin#:   12     [16] Mcst:    0      [27] CLP enb: Y      [38] EFCI: 100
[06] BF VPI:  64     [17] Mc grp:  1      [28] FST enb: N      [39] CLP hi: 100
[07] BF VCI:  0      [18] & msk: 0000000F [29] FST MIR: 500    [40] CLP lo: 100
[08] Pl Cls:  0      [19] | msk: 06400640 [30] FST PIR: 500    [41] BCM:    N
[09] Rmt lp:  N      [20] Prt QBN: 2      [31] FST QIR: 500    [42] Inhibit:N
[10] VPI:   00000064 [21] UPC GCR: 0      [32] QIR TO:  0      [43] UPC enb:Y
Last Command: dspasich 5.1 1 N
Next Command:

dspbuses (Display Bus Status)

Displays the available MUXBUS or CELLBUS bandwidth. The display does not dynamically receive updates and is therefore a snapshot. The dspbuses command lists the dedicated and pooled bandwidth units as well as the status of the available MUXBUS.

Attributes

Jobs: No Log: No Lock: No Node Type: IPX, IGX, BPX

Associated Commands

cnfbus

Syntax

Function

This command displays the available MUXBUS bandwidth. The display is not updated and is referred to as a snapshot. The command lists the dedicated and pooled bandwidth units as well as the status of the available MUXBUS or CELLBUS. Figure 1-55 illustrates the dspbuses display on a BPX node. Figure 1-56 illustrates the dspbuses display on an IGX node

bpx1       TN    StrataCom       BPX 15    8.5 July 2 1997  13:22 GMT 
 
                               Bus Status
 
 
Bus A (slot 7): Active - OK
 
Bus B (slot 8): Standby - OK
 
 
 
 
                                                                                
Last Command: dspbuses
 
 
Next Command: 

pubsbpx1       TN    StrataCom       BPX 15    8.4.0j    July 2 1997  13:22 GMT 
 
                               Bus Status
 
 
Bus A (slot 7): Active - OK
 
Bus B (slot 8): Standby - OK
 
 
 
 
 
 
 
 
 
                                                                                
Last Command: dspbuses
 
 
Next Command: 

dspcardstats (Display BXM Card Statistics)

The dspcardstats command displays the collected BXM card statistics for the selected node slot.

Attributes

Jobs: Yes Log: Yes Lock: Yes Node Type: BPX

Associated Commands

cnfslotstats

Syntax

Function

This command displays all card statistics for an active BXM card in the current node. Refer to Figure 1-57 illustrates screen displayed after entering the dspcardstats command.

sw59           TN    StrataCom       BPX 15    8.5 Date/Time Not Set
ASI-T3 12       Status: Clear - Slot OK                 Clrd: Date/Time Not Set
Type      Count ETS   Status    Type          
utopia-2 discard count        0     0
utopia-2 misalign count       0     0
atm fr. pyld parity err     	0      0
bfr hdr parity err     	0     0
null bfrm header err     	0     0
brame hoq req t/o     	0     0
poll bus parity err     	0     0
bfr queue parity err     	0     0
bfr bip16 parity err     	0     0
mc addr tbl parity err     	0     0
eap arfd pndg err     	0     0
                                                                                                                                                   
This Command: dspcardstats 12 
Continue?

dspcderrs (Display Card Errors)

The dspcderrs command displays detailed card failure information resulting from card diagnostics testing at the local node.

Attributes

Jobs: No Log: No Lock: No Node Type: IPX, IGX, BPX

Associated Commands

clrcderrs, prtcderrs

Syntax

Function

This command displays a history of card failures associated with a specified slot. If no argument is specified, a summary is displayed, indicating which slots have failures recorded against them. The command displays the results of the self tests and background tests as well as the total hardware errors.

To clear the card error counters, use the clrcderrs command. To obtain a hard copy of the report, use the prtcderrs command. Figure 1-58 illustrates the command display.

sw83           TN    StrataCom       IPX 16    8.5      Aug. 1 1997  17:56 PST
AIT in Slot 11 : 176767 Rev AEF     Failures Cleared: Aug. 19 1997 11:25:29 PST
----------------------------------- Records Cleared:  Aug. 20 1997 13:14:03 PST
Self Test          Threshold Counter: 0          Threshold Limit: 300
Total Pass: 0             Total Fail: 0              Total Abort: 0
First Pass:                            Last Pass:
First Fail:                            Last Fail:
Hardware Error     Total Events: 0     Threshold Counter: 0
First Event:                           Last Event:
Last Command: dspcderrs 11
Next Command:

dspcftst (Display Comm. Fail Test Pattern)

The dspcftst command displays the test pattern used for the communications fail test.

Attributes

Jobs: No Log: No Lock: No Node Type: IPX, IGX, BPX

Associated Commands

cnfcftst

Syntax

Function

This command displays the test pattern used to test the controller communication path to a node that does not respond to normal controller traffic. The test pattern defaults to an alternating 8-byte sequence of 00 and FF. Refer to cnfcftst command for other patterns and how to reconfigure this pattern. Figure 1-59 illustrates the command display.

sw83           TN    StrataCom       IPX 16    8.5      Aug. 1 1997  17:57 PST
Comm Fail Test Pattern.
    Byte  0: FF     Byte 12: 00     Byte 24: FF     Byte 36: 00     Byte 48: FF
    Byte  1: FF     Byte 13: 00     Byte 25: FF     Byte 37: 00     Byte 49: FF
    Byte  2: FF     Byte 14: 00     Byte 26: FF     Byte 38: 00     Byte 50: FF
    Byte  3: FF     Byte 15: 00     Byte 27: FF     Byte 39: 00     Byte 51: FF
    Byte  4: 00     Byte 16: FF     Byte 28: 00     Byte 40: FF     Byte 52: 00
    Byte  5: 00     Byte 17: FF     Byte 29: 00     Byte 41: FF     Byte 53: 00
    Byte  6: 00     Byte 18: FF     Byte 30: 00     Byte 42: FF     Byte 54: 00
    Byte  7: 00     Byte 19: FF     Byte 31: 00     Byte 43: FF     Byte 55: 00
    Byte  8: FF     Byte 20: 00     Byte 32: FF     Byte 44: 00     Byte 56: FF
    Byte  9: FF     Byte 21: 00     Byte 33: FF     Byte 45: 00     Byte 57: FF
    Byte 10: FF     Byte 22: 00     Byte 34: FF     Byte 46: 00     Byte 58: FF
    Byte 11: FF     Byte 23: 00     Byte 35: FF     Byte 47: 00     Byte 59: FF
Last Command: dspcftst
Next Command:

dspchan (Display Channel Configuration)

The dspchan command displays the configuration of various IPX or IGX voice channels.

Attributes

Jobs: No Log: No Lock: No Node Type: IPX, IGX

Associated Commands

cnfcdpparm

Syntax

Function

This command displays the configuration of IPX or IGX voice channels. It is primarily a debug command and allows inspection of the data structure defining a channel. Parameters for voice and signalling processing on a CDP or CVM voice channel are displayed by this command. Table 1-31 lists the parameters. Many of these parameters are also displayed elsewhere. Figure 1-60 illustrates the command display.

sw83           TN    StrataCom       IPX 16    8.5     Aug. 1 1997  18:06 PST
Channel Data Base for CDP card  7  chan. 000000 at address 30BF29EC
VC Index      -1                 Onhk C         4
In Loss       0                  Onhk D         4
Out Loss      0                  Dial Type      0
Chan Type     1                  TX A bit       1
Sig. Intg     96                 TX B bit       1
Xmt. dlay     5                  TX C bit       0
Smpl dlay     1                  TX D bit       1
Bk noise      67                 RX A bit       1
DSI smple     168                RX B bit       1
Chan Util     40                 RX C bit       0
Onhk A        3                  RX D bit       1
Onhk B        3                  Signalling     TSP MODE
This Command: dspchan 7.1
Continue?

sw83           TN    StrataCom       IPX 16    8.5      Aug. 1 1997  18:07 PST
Channel Data Base for CDP card  7  chan. 000000 at address 30BF29EC
Echo supr     1                  TX A Qual      3
Hi Pass F     1                  TX B Qual      3
Float         1                  TX C Qual      3
es loss       1                  TX D Qual      3
Fmodem        64                 RX A Qual      3
ADV           1                  RX B Qual      3
Cond ID       0                  RX C Qual      3
Wink Puls     20                 RX D Qual      3
END OF UNI CNFG
This Command: dspchan 7.1
Continue?

sw83           TN    StrataCom       IPX 16    8.5.     Aug. 1 1997  18:07 PST
Channel Data Base for CDP card  7  chan. 000000 at address 30BF29EC
TX CODE       3                  iec cancel     0
RX CODE       3                  iec nlp        1
TX SIG        0                  iec converg.   1
RX SIG        0                  iec erl lvl    1
CLR CHN       0                  iec Hregs.     1
SIG RATE      0                  iec tone dsbl  1
PLY MSBhx     1                  adpcm flag     0
PLY LSBhx     90
In use        0
DPU           -
Last Command: dspchan 7.1
Next Command:

dspchstatcnf (Display Statistics Enabled for a Channel)

The dspchstatcnf command displays the configuration of enabled statistics for a channel.

Attributes

Jobs: No Log: Yes Lock: Yes Node Type: IPX, IGX

Associated Commands

cnfchstats, dspchstathist

Syntax

Function

The dspchstatcnf command displays the enabled interval statistics for a channel. It is intended to help debug problems with statistics gathering. The command output is a list of the connection statistics as set by the cnfchstats command, by StrataView Plus, or by IPX or IGX features. Figure 1-61 illustrates a typical example.

The Owner column identifies who or what set the statistic. If the Owner column shows "Automatic," the node's features set the statistic. If the node name appears under Owner, StrataView Plus set the statistic. If the user name appears under Owner, the cnfchstats command executed from the command line interface set the statistic.

pubsbpx1       VT    StrataCom       BPX 15    8.5       May  24 1997 23:13 GMT
Statistics Enabled on Channel 5.1.100.100
    Statistic                            Samples Interval Size Peaks  Owner
    ------------------------------------ ------- -------- ---- -----  ----------
41) AAL5 Cells Discarded for VCQ Full          1       30    4  NONE  TFTP
42) Average VCq Depth in Cells                 1       30    4  NONE  TFTP
43) Cells lost due to Rsrc Overflow            1       30    4  NONE  TFTP
44) Cells discarded for SBIN full              1       30    4  NONE  TFTP
45) Cells Transmitted with EFCI(Port)          1       30    4  NONE  TFTP
46) Cells Transmitted(Port)                    1       30    4  NONE  TFTP
47) Cells Received from Network                1       30    4  NONE  TFTP
48) Cells discarded for QBIN full              1       30    4  NONE  TFTP
49) Cells discarded when QBIN>CLP              1       30    4  NONE  TFTP
50) Cells Transmitted with CLP (Port) 		1       30    4  NONE  TFTP
51) BCM Cells Received(Port)                   1       30    4  NONE  TFTP
This Command: dspchstatcnf 5.1.100.100
Continue?

dspchstathist (Display Statistics History for a Channel)

The dspchstathist command displays a history of statistics configured as enabled for a channel.

Attributes

Jobs: No Log: Yes Lock: Yes Node Type: IPX, IGX, BPX

Associated Commands

cnfchstats, dspchstatcnf

Syntax

Function

This command displays a history of the enabled statistics for a selected channel. It is intended for debugging problems with statistics gathering. It displays the data for the last five occurrences of the channel statistic. The channel statistic is selected from the list displayed when this command is first entered.

Use the dspchstatcnf to display the statistics enabled on the selected channel. Record the statistics types enabled, the collection interval, and owner; you will need this information to obtain the statistics history. Use cnfchstats to enable a statistic if it is not already enabled. Figure 1-62 illustrates a display for channel 6.1 packets transmitted (1 second interval) history.

gamma            TRM       SuperUser        Rev:  8.5  Aug. 14 1997 13:53 PDT 
Packets Transmitted on Channel 6.1                                           
Interval: 1 Minute(s), Data Size: 4 Byte(s), NO Peaks, Owner: Automatic 
0   -       1699
-1   -       1698
-2   -       1698
-3   -       1699
-4   -       1698
-5   -       1698
-6   -       1698
-7   -       1699
-8   -       1697
-9   -       1699
Last Command: dspchstathist 6.1 7 1 AUTO
Next Command:

dspchstats (Display All Enabled Statistics For A Channel)

The dspchstats command displays all statistics configured as enabled for a selected channel.

Attributes

Jobs: No Log: Yes Lock: Yes Node Type: IPX, IGX, BPX

Associated Commands

cnfchstats, dspchstatcnf

Syntax

Function

This command displays the enabled statistics for the selected channel. It is intended for debugging problems with statistics gathering. It displays the data for the last five occurrences of the channel statistic. The channel statistic is selected from the list displayed when this command is first entered.

Use the dspchstats command to display the statistics enabled on the selected channel. Record the statistics types enabled, the collection interval, and owner; you will need this information to obtain the statistics history. Use cnfchstats to enable a statistic if it is not already enabled. Figure 1-63 illustrates a display for channel on port 3, slot 1, with VPI and VCI both set to 1.

Channel Statistics for 3.1.1.1     Cleared: Date/Time Not Set   (\)  Snapshot
PCR: 500 cps            Collection Time: 0 day(s) 00:03:47      Corrupted: NO
   Traffic      Cells      Avg CPS   %util  
From Port   :  11855761    52008     10401  
To Network  :    114332    501       100  
From Network:    114303    501       100  
To Port     :    114303    0         501  
                                                                                
Last Command: dspchstats 3.1.1.1.1
Next Command: 

dspclnstatcnf (Display Circuit Line Statistics Configuration)

The dspclnstatcnf command displays statistics configured as enabled for a selected circuit line.

Attributes

Jobs: No Log: Yes Lock: Yes Node Type: IPX, IGX

Associated Commands

cnfclnstats

Syntax

<line> Specifies the circuit line in the format slot or slot.line. If the card has only one line, you can enter just the slot.

Function

This command displays the circuit line statistics as enabled by the cnfclnstats command, by StrataView Plus, or by IPX or IGX features. See Figure 1-64 for an example display.

The Owner column shows what set the statistic. If the owner is "Automatic," the statistic was derived from the features. If the node name appears under Owner, the statistic came from StrataView Plus. If "User" is under Owner, the source of the statistic was the cnfchstats command.

sw83           TN    StrataCom       IPX 16    8.5      Aug. 1 1997  18:14 PST
Statistics Enabled on Circuit Line 7
Statistic                            Samples  Interval  Size  Peaks  Owner
-----------------------------------  -------  --------  ----  -----  ----------
Frames Slips                              60         0     4   NONE  IPX
Out of Frames                             60         0     4   NONE  IPX
Losses of Signal                          60         0     4   NONE  IPX
Frames Bit Errors                         60         0     4   NONE  IPX
CRC Errors                                60         0     4   NONE  IPX
Out of Multi-Frames                       60         0     4   NONE  IPX
All Ones in Timeslot 16                   60         0     4   NONE  IPX
Last Command: dspclnstatcnf 7
Next Command:

dspclnstathist (Display Statistics History for a Circuit Line)

The dspclnstathist command displays a history of statistics enabled for a circuit line.

Attributes

Jobs: No Log: Yes Lock: Yes Node Type: IPX, IGX

Associated Commands

cnfclnstats, dspclnstatcnf

Syntax

Function

This command displays the last five occurrences of the circuit line statistic. The circuit line statistic is selected from the list displayed when you first enter this command. Use the dspclnstatcnf to display the statistics enabled for the selected channel. Use cnfclnstats to enable a statistic.

Figure 1-65 illustrates a display for T1 circuit line 14 bipolar violations (60 second interval) history.

gamma            TRM       SuperUser        Rev:  8.5  Aug. 14 1997 14:00 PDT 
Bipolar Violations on Circuit Line 14
Interval: 60 Minute(s), Data Size: 4 Byte(s), 10 S Peaks, Owner: Automatic
 0   -          0(0)
-1   -          0(0)
-2   -          0(0)
-3   -          0(0)
-4   -          0(0)
Last Command: dspclnstathist 14 1 60 AUTO 
Next Command:

dspcnf (Display Configuration Save/Restore Status)

The dspcnf command displays the status for the configuration save/restore processes on all nodes in the network.

Attributes

Jobs: No Log: No Lock: No Node Type: IPX, IGX, BPX

Associated Commands

savecnf, loadcnf, runcnf

Syntax

Function

This command displays the status for the configuration save/restore process. The display lists the various nodes, the backup ID name of the saved configuration, the time and date saved, and the StrataView Plus terminal it is saved on. See Figure 1-66 for an example.

If the status displays "Reserved for Firmware," a firmware image is being maintained in memory after being loaded. Use the getfwrev 0.0 command to clear the firmware image. Likewise, if a configuration image is displayed, clear the old configuration image using savecnf clear or loadcnf clear.

sw83           TN    StrataCom       IPX 16    8.5     Aug. 24 1997  18:21 PST
Node     Backup ID Revision Date/Time (GMT)   Status
-------- --------- -------- ----------------- ---------------------------------
sw78     mark      8.5.00 02/22/97 16:36:26 Unreachable
sw81     mark      8.5.00 02/22/97 16:36:26 Unreachable
sw84     mark      8.5.00 02/22/97 16:36:26 Save on SV+ at sw78 complete
sw79     mark      8.5.00 02/22/97 16:36:26 Save on SV+ at sw78 complete
sw86     mark      8.5.00 02/22/97 16:36:26 Unreachable
sw83     mark      8.5.00 02/22/97 16:36:26 Save on SV+ at sw78 complete
Last Command: dspcnf
Next Command:

dspdnld (Display Download)

The dspdnld command displays the status of a download to a nodes.

Attributes

Jobs: No Log: Yes Lock: No Node Type: IPX, IGX, BPX

Associated Commands

loadrev, getfwrev

Syntax

Function

This command displays the status of any software or firmware download operation from StrataView Plus to the node controller card. You should be connected to the node being downloaded either directly or via virtual terminal connection. The display download command shows:

• download destination--node currently being downloaded.

• download type--destination of the downloaded image, standby RAM or active or standby ROM, or firmware.

• download source--where the image to be downloaded is currently stored, StrataView or StrataView Plus, standby controller, active or standby controller, or remote node.

• download image--where the image is located, ROM or RAM.

This command can be used to check how far along the download has progressed. Figure 1-67 illustrates the command screen. Blocks of data already downloaded appear highlighted; the remaining blocks are appear dim. If there was no download initiated when this command is entered, the blocks of data will appear as all zeros.

sw83           TN    StrataCom       IPX 16    8.5      Aug. 1 1997  18:23 PST
dl_dest:  Active CC                    dl_source: Active CC
dl_type:  None                         dl_image:  ROM       (NPC)
30010800  30020800  30030800  30040800  30050800  30060800  30070800  30080800
30090800  300A0800  300B0800  300C0800  300D0800  300E0800  300F0800  30100800
30110800  30120800  30130800  30140800  30150800  30160800  30170800  30180800
30190800  301A0800  301B0800  301C0800  301D0800  301E0800  301F0800  30200800
30210800  30220800  30230800  30240800  30250800  30260800  30270800  30280800
30290800  302A0800  302B0800  302C0800  302D0800  302E0800  302E3E7C
Last Command: dspdnld
Next Command:

dspdutl (Display Data Channel Utilization)

The dsputl command displays the percentage utilization for data connections.

Attributes

Jobs: No Log: No Lock: No Node Type: IPX, IGX

Associated Commands

dsputl

Syntax

Function

This command displays the percentage utilization for the data connections starting at the back slot (bslot) number specified. All data connections for the node are displayed (maximum of 32).

The percentage is calculated by dividing the number of packets transmitted over the total number of packets allocated to the specified channel. Only transmit packet rates are used. If percentage utilization exceeds configured utilization the channel appears in reverse video.

Figure 1-68 illustrates a display where there is very low utilization (2%) on three of the four ports and no utilization of the forth port. The clear option clears all slots. Use dsputl to display utilization for voice channels.

sw150          TN    StrataCom       IGX 16    8.5    Aug. 1 1997  20:07 GMT
Percentage utilization        Last Cleared: Date/Time Not Set         Snapshot
From
Slot  1  2  3  4  5  6  7  8    Slot  1  2  3  4  5  6  7  8
13    6 99 99
Last Command: dspdutl 13
Next Command:

dspecparm (Display Echo Canceller Parameters)

The dspecparm command displays statistics configured as enabled for a selected CDP echo canceller.

Attributes

Jobs: No Log: Yes Lock: No Node Type: IPX, IGX

Associated Commands

cnfecparm

Syntax

Function

This command displays the Integrated Echo Canceller card parameters associated with the specified circuit line. These parameters are set using the cnfecparm command. Table 1-32 lists the parameter options. Figure 1-69 illustrates a typical display.

sw83           TN    StrataCom       IPX 16    8.5.     Aug. 1 1997  18:34 PST
IEC Line 7 Parameters
1  CDP IEC Echo Return Loss High (.1 dBs)  [            60] (D)
2  CDP IEC Echo Return Loss Low  (.1 dBs)  [            30] (D)
3  CDP IEC Tone Disabler Type              [         G.164]
4  CDP IEC Non-Linear Processing           [Center Clipper]
5  CDP IEC Non-Linear Processing Threshold [            18] (D)
6  CDP IEC Noise Injection                 [       Enabled]
7  CDP IEC Voice Template                  [           USA]
Last Command: dspecparm 7
Next Command:
IPX SU/0036_

dspfpdsc (Display FastPAD Card Descriptor)

The dspfpdsc command displays FastPAD card descriptor information.

Attributes

Jobs: No Log: No Lock: No Node Type: IPX, IGX, BPX

Associated Commands

dspfp, dspfps

Syntax

Function

This command displays FastPAD card descriptor information including:

• Card in use

• Card state

• FastPAD configuration index

• FastPAD port index

Figure 1-70 illustrates the system response.

cc7            VT    StrataCom       IPX 32    8.5     Aug. 30 1997 11:08 PST
                    FastPad Card Descriptor Configuration
    Card in Use   :  01     Card State    :  03     FPD CNFG indx :  00
                              Port Index Array
                              FastPad Port Indx
          0    1    2    3    4    5    6    7    8    9    A    B
         0000 0001 0002 0003 0004 0005 0006 FFFF FFFF FFFF FFFF FFFF
Last Command: dspfpdsc 31.2.B
Next Command:

dspfwrev (Display Firmware Revision)

The dspfwrev command displays the status of card firmware revision image loaded in the controller card's RAM.

Attributes

Jobs: No Log: No Lock: No Node Type: IPX, IGX, BPX

Associated Commands

getfwrev, burnfwrev

Syntax

Function

This command displays the revision level and an indication of the length of the firmware in the controller card. It may require two screens to display all the parameters. Figure 1-71 illustrates the screen display. This command can be used during firmware download to get an idea of how far along the downloading process has progressed. The blocks already downloaded appear normal. Blocks that are yet to be downloaded appear shaded.

If no getfwrev command was issued, nothing displays. If "Configuration image present" displays, use the loadcnf clear command to clear this status.

gamma            TRM       SuperUser        Rev:  8.5  Aug. 14 1997  14:28 PDT
Firmware        Size        Status
F.D.A           256 K       Complete
File            Address     Length      CRC           Burn Address
File            Address     Length      CRC           Burn Address
1               800800      410         22996DDA
1               800800      410         22996DDA
3               805E60      480         85CB29EA
4               80A630      70          57A938AE
4               80A630      70          57A938AE
6               810000      10000       338E45F6
7               820000      4400        95990113
8               835000      1810        875771B2
9               8368A0      15D0        4C597B97
This Command: dspfwrev
Continue?
gamma            TRM       SuperUser        Rev:  8.5  Aug. 14 1997  14:29 PDT 
Firmware        Size        Status
F.D.A           256 K       Complete
File            Address     Length      CRC           Burn Address
10              838000      20F0        0F4898D2
11              83A100      1E20        175F4B39
12              83C000      2FC0        F39B0302
13              83F000      1B0         E755FE4E
14              83FFFE      2           A1F4726D
Last Command: dspfwrev 
Next Command:

dsplnstatcnf (Display Statistics Enabled for a Line)

The dsplnstatcnf command displays statistics configured as enabled for a selected line.

Attributes

Jobs: No Log: Yes Lock: Yes Node Type: IPX, IGX

Associated Commands

cnflnstats

Syntax

Function

This command displays the line statistics as enabled by the cnflnstats command, by StrataView Plus, or by node features. Figure 1-72 illustrates an example display.

The Owner column identifies who or what set the statistic. If the Owner column shows "Automatic," the node's features set the statistic. If the node name appears under Owner, StrataView Plus set the statistic. If the user name appears under Owner, the cnfchstats command executed from the command line interface set the statistic.

cc2            LAN   StrataCom       IPX 32    8.5     Aug. 30 1997 11:38 PST
Statistics Enabled on Circuit Line 15
Statistic                            Samples  Interval  Size  Peaks  Owner
-----------------------------------  -------  --------  ----  -----  ----------
Bipolar Violations                        60         0     4   NONE  IPX
Frames Slips                              60         0     4   NONE  IPX
Out of Frames                             60         0     4   NONE  IPX
Losses of Signal                          60         0     4   NONE  IPX
Frames Bit Errors                         60         0     4   NONE  IPX
CRC Errors                                60         0     4   NONE  IPX
Out of Multi-Frames                       60         0     4   NONE  IPX
All Ones in Timeslot 16                   60         0     4   NONE  IPX
Last Command: dsplnstatcnf 15
Next Command:

dsplnstathist (Display Statistics Data for a Line)

The dsplnstathist command displays a history of statistics configured as enabled for a selected line.

Attributes

Jobs: No Log: Yes Lock: Yes Node Type: IPX, IGX

Associated Commands

cnflnstats, dsplnstatcnf

Syntax

Function

This command displays the last five occurrences of the line statistic. The line statistic is selected from the list displayed when this command is first entered. Use the dsplnstatcnf to display the statistics enabled on the selected channel. Use cnflnstats to enable a statistic.

Figure 1-73 illustrates an example display.

cc2            LAN   StrataCom       IPX 32    8.5     Aug. 30 1997 11:40 PST
Command history
12: cnftcpparm
11: cnftcpparm 32
10: cnfnwip 192.38.38.2
 9: cnfnwip 192.38.38.2 255.255.255.0
 8: help cnft
 7: dspasich
 6: dspasich
 5: dspasich
 4: dspbuses
 3: dsplnstatcnf 15
 2: dsplnstathist 15 5 40
 1: dsplnstathist 15 5 40 IPX
Last Command: dsplnstathist 15 5 40 IPX
Next Command:

dspplnmcons (Display Packet Line Connection Counts)

The dspplnmcons command displays the number of packet line connections by master node.

Attributes

Jobs: No Log: No Lock: No Node Type: IPX, IGX

Associated Commands

none

Syntax

Function

Displays the number of connections attached to each master node on a specified line. See Figure 1-74, below.

TN    StrataCom       IPX 16    8.5    Aug. 25 1997 18:31 PST
Connection Counts For PLN 11
Mst Node  Conns    Mst Node  Conns    Mst Node  Conns    Mst Node  Conns
sw81      48       sw83      400      sw84      48       sw79      500
sw86      100
Last Command: dspplnmcons 11

dspportstatcnf (Display Statistics Enabled For A FR Port)

The dspportstatcnf command displays statistics configured as enabled for a selected Frame Relay port.

Attributes

Jobs: No Log: Yes Lock: Yes Node Type: IPX, IGX

Associated Commands

cnfportstats

Syntax

Function

This command displays the enabling of Frame Relay port statistics. These are the statistics set by the cnfportstats command, by StrataView Plus, or by node features. See Figure 1-75 for an example.

The owner column shows what set the statistic. If "Automatic", it is set by features, if node name it was is set by StrataView Plus, if user it was set with the cnfportstats command.

gamma            SV+       YourID           Rev:  8.5  Aug. 14 1997 13:47 PDT 
Statistics Enabled on Port 8.1
Statistic                             Samples  Interval  Size  Peaks  Owner
------------------------------------  -------  --------  ----  -----  ----------
Frames Received                             5        60     4    1 M  beta
Frames Received                             5        60     4    1 M  beta
Bytes Received                              5        60     4    1 M  beta
Last Command: dspportstatcnf 8.1

dspportstathist (Display Statistics History For A FR Port)

The dspportstathist command displays a history of statistics configured as enabled for a selected Frame Relay port.

Attributes

Jobs: No Log: Yes Lock: Yes Type: IPX, IGX

Associated Commands

cnfportstats, dspportstatcnf

Syntax

Function

This command displays the data for the last five occurrences of the port statistic. The port statistic is selected from the list displayed when this command is first entered. Use the dspportstatcnf to display the statistics enabled on the selected port. Use cnfportstats to enable a statistic.

Figure 1-76 illustrates a display for FR port 8.2 DE Frames Dropped (1 second interval) history.

D.1 gamma        TRM       SuperUser        Rev:  8.5 Aug. 14 1997 14:15 PDT 
DE Frames Dropped on Port 8.2
Interval: 1 Minute(s), Data Size: 4 Byte(s), NO Peaks, Owner: IPX User
 0   -          0
-1   -          0
-2   -          0
-3   -          0
Last Command: dspportstathist 8.2 19 1 USER
Next Command:

dsprevs (Display Revisions)

The dsprevs command displays the system software revision loaded and running on all nodes in the network.

Attributes

Jobs: No Log: No Lock: No Node Type: IPX, IGX, BPX

Associated Commands

runrev, loadrev, forcerev

Syntax

Function

This command displays the configuration and status of the primary and secondary software revisions for all nodes in the network. The primary revision is the software that is running the node. The secondary revision is the software that is available in memory but not being run. Table 1-33 lists the various status messages. Figure 1-77 and Figure 1-78 illustrate a typical display.

sw83           TN    StrataCom       IPX 16    8.5      Aug. 1 1997  19:03 PST
                   ------ Primary ------         ----- Secondary -----
NodeName           Status       Revision         Status       Revision
sw78               Running      8.5.00
sw81               Running      8.5.00
sw84               Running      8.5.ay
sw79               Running      8.5.1f
sw86               Running      8.5.00
sw83               Running      8.5.1f
Last Command: dsprevs
Next Command:

D1.jea         TRM   StrataCom       BPX 15     8.5    Aug. 14 1997 12:20 PDT
Robust Communications Statistics since : Date/Time Not Set 
Updts msg xmit:      0
Updts msg ackd:      0
Updts ack tout:      0
LCBs freed:          0
Updts ack reset:     0
Last Command: dsprobparm
Next Command:

dsprobst (Display Robust Statistics)

The dsprobst command displays the statistics associated with the Robust Alarms feature.

Attributes

Jobs: No Log: No Lock: No Node Type: IPX, IGX, BPX

Associated Commands

cnfrobparm

Syntax

Function

This command displays the statistics associated with the Robust Alarms messages between the node and StrataView Plus NMS. The optional "clear" argument clears the statistics buffers. Figure 1-79 illustrates a sample display screen.

cc2            LAN   StrataCom       IPX 32    8.5 Aug. 30 1997 11:40 PST
Command history
12: cnftcparm
11: cnftcpparm 32
10: cnfnwip 192.38.38.2
 9: cnfnwip 192.38.38.2 255.255.255.0
 8: help cnft
 7: dspasich
 6: dspasich
 5: dspasich
 4: dspbuses
 3: dsplnstatcnf 15
 2: dsplnstathist 15 5 40
 1: dsplnstathist 15 5 40 IPX
Last Command: dsplnstathist 15 5 40 IPX
Statistic not enabled for specified object
Next Command:

dsprrst (Display Reroute Statistics)

The dsprrst command displays the connection rerouting statistics for the network.

Attributes

Jobs: No Log: No Lock: No Node Type: IPX, IGX, BPX

Associated Commands

rrtcon, drtop

Syntax

Function

This command displays the statistics related to connection rerouting resulting from failed trunks. These statistics may be useful in determining the performance of the reroute algorithm. Use the "clear" option to clear the counters before accumulating the statistics. Table 1-34 lists the applicable reroute statistics. Figure 1-80 illustrates a typical display.

sw91           TN    StrataCom       IPX 8     8.5    Aug. 1 1997  20:56 GMT
          Connection Routing Statistics LOC_DOMAIN
Number of Completed Routes:         0  Blocked by other st machines:      273
Number of Failed Routes:            0  Timeouts waiting for ACK/NACK:       0
Number of Collisions:               0  Number of Routes Not found:          0
Max # of Consec Collisions:         0  # of Rrts with rrt_req bit set:      0
Max Secs To Select Route:       0.000  Address of Forced Rrt Counts: 30CDC386
Max Secs To Perform Route:      0.000  Max routes checked in search:        0
Max Bundle Size Routed:             0  Max good rts checked in search:      0
Avg Secs To Select Route:       0.000  # nibs rmvd out from under us:     118
Avg Secs To Perform Route       0.000  # our lns rmvd from under us:        0
Avg Secs To Route a Conn:       0.000  # lns rmvd from under us:           66
Avg Bundle Size Routed:             0  Number of conid conflicts:           0
% of Collisions/Rrt Attempt:        0% Number of LCON deroutes:             0
Max Secs To NOT find Route:     0.005  Number of NW_LCON deroutes:          0
Times conns deletd while rtng:      0  Number of GLCON lcl deroutes:        0
Last Command: dsprrst
Next Command:

dspsig (Display Signalling)

The dspsig command displays the current signalling state received at the node from the specified voice channel.

Attributes

Jobs: No Log: No Lock: No Node Type: IPX, IGX

Associated Commands

cnfclnsigparm, cnfrcvsig, dspclnsigparm

Syntax

Function

This command displays the current signalling state received at the node from the specified voice channel. The status of the transmit and receive A and B signalling bits (for DS1 trunks) or A, B, C and D signalling bits (for E1 trunks) are displayed as a 0 or 1. The status of the bits (0 or 1) depends on the signalling type utilized on the connection displayed. The transmit direction of transmission is towards the remote node; the receive direction is towards the local circuit line.

The dspsig command can be used to verify the connection signalling type. Figure 1-81 illustrates a typical screen. If you compare the A/B bit states on-hook and off-hook with those shown in the dspchcnf command, you will note that the node passes signalling straight through. The signalling definition is only important for monitoring the on-hook/off-hook state and setting conditioning patterns.

sw83           TN    StrataCom       IPX 16    8.5      Aug. 1 1997  19:25 PST
                                Signalling Information
From 7.1    TXAbit  TXBbit  TXCbit  TXDbit  RXAbit RXBbit RXCbit RXDbit no_serv
7.1-15      1       1       0       1       1      1      0      1
7.17-31     1       1       0       1       1      1      0      1
Last Command: dspsig 7.1
Next Command:

dspslot (Display Slot)

The dspslot command displays system information associated with a specific card in the node.

Attributes

Jobs: No Log: No Lock: No Node Type: IPX, IGX, BPX

Associated Commands

none

Syntax

Function

This command displays system information associated with a specific card in the node. The information can help you debug card failures. When a card failure is reported to the Cisco TAC, the TAC engineer records the parameters for the associated card displayed by using dspslot.

The information displayed by the dspslot command is unique to the card and is used primarily by the controller card to supervise background system tasks. Table 1-35 lists the card parameters. Figure 1-82 illustrates a typical display--an FRP in this case.

Use this command to add information on a failed card when you return it. Print the screen or otherwise record the information and return it with the faulty card to Cisco.

sw83           TN    StrataCom       IPX 16    8.5      Aug. 1 1997  19:27 PST
Card Data Base for FRP card in slot 6  at address 30BD820C
  Logical Card        6                     Test in Prog        0
  Verify DB Flag      0                     Slft Res Abort      0
  Info Ptr            30B88C2C              Slft Abort          0
  Last Event          TEST_FREE             Last Test           BKGD_TEST
  Fail Inter          0                     FRP Test Fail       0
  Selftest Fail       0                     FRP Test Fail I     0
  Selftest Inter      0                     FRP Port Test Fail  0
  Selftest Timeout    0                     FRP Port Capacity   31
  Con Test Fail       0                     FRP Line Capable    1
  Red LED Flag        0                     FRP V35 Capable     0
  Restart Reason      Not maintained        FRP X21 Capable     0
  Selftest Results                          FRP NNI/CLLM Cap    1
                                            FRP CGW/ATFR Cap    1
Last Command: dspslot 6
Next Command:

dspslotstatcnf (Display Statistics Enabled for a BXM Card Slot)

The dspslotstatcnf command displays statistics configured as enabled for a selected slot where a BXM card resides.

Attributes

Jobs: No Log: Yes Lock: Yes Node Type: BPX

Associated Commands

cnfslotstats

Syntax

Function

This command displays the enabled BXM card slot statistics. These statistics set by the cnfslotstats command, by StrataView Plus, or by node features.

The "Owner" column shows what set the statistic, as follows:

• If the column shows "Automatic," it was set by features.

• If the column shows the node name, it was is set by StrataView Plus.

• If the column shows the name of the user, it was set with the cnfslotstats command.

dspslotstathist (Display Statistics History for a BXM Card)

The dspslotstathist command displays a history of statistics enabled for a BXM card slot.

Attributes

Jobs: No Log: Yes Lock: Yes Type: BPX

Associated Commands

cnfslotstats, dspslotstatcnf

Syntax

Function

This command displays the data for the last five occurrences of the slot statistic. The statistic is selected from the list displayed when this command is first entered. Use the dspslotstatcnf to display the statistics enabled on the selected slot. Use cnfslotstats to enable a statistic.

dspstatmem (Display Statistics Memory Use)

The dspstatmem command displays memory usage for statistics collection.

Attributes

Jobs: No Log: Yes Lock: No Node Type: IPX, IGX, BPX

Associated Commands

none

Syntax

Function

This command displays memory usage for statistics collection. It is intended for debugging statistics collection problems, not everyday use. The command shows the amount of controller card memory allocated by the user to statistics display (defaults to 650 Kbytes).

The memory occupied by USER is used for user-enabled statistics. Figure 1-83 illustrates a typical screen. The memory occupied by USER figure is that used by the StrataView Plus user. Memory occupied by AUTO is that used by node features.

sw83           TN    StrataCom       IPX 16    8.5      Aug. 1 1997  19:29 PST
User Configured Statistics Memory (In bytes)  = 624640
Memory Occupied by USER (In bytes) = 0
Memory Occupied by AUTO (In bytes) = 21584
Last Command: dspstatmem
Next Command:

dsptcpparm (Display TCP Parameters)

The dspftcpparm command displays the TCP bandwidth throttle parameter.

Attributes

Jobs: No Log: No Lock: No Node Type: IPX, IGX, BPX

Associated Commands

cnftcpparm

Syntax

Function

This command displays the TCP bandwidth throttle parameter. Figure 1-84 shows a typical display.

cc2            LAN   StrataCom       IPX 32    8.5     Aug. 30 1997 11:42 PST
NWIP Bandwidth Throttle (Kbytes/sec):  32
Last Command: dsptcpparm
Next Command:

dsptrkcons (Display Trunk Connection Counts)

The dsptrkcons command displays the number of connections routed over the specified trunk. This command applies to physical and virtual trunks.

Attributes

Jobs: No Log: No Lock: No Node Type: IPX, IGX, BPX

Associated Commands

dsptrkmcons, dspplnmcons

Syntax

Function

This command displays the total number of connections being carried by the specified trunk. The connections are summed for each terminating node in the network and lists the connection count for the transmit direction (out of the node).

This command is useful in determining the source of dropped packets in cases where the specified trunk is oversubscribed. Use the dsptrks command to list the trunks that originate at each node. Next, use the dsptrkcons to determine the number of connections (the more connections per trunk the greater the possibility of over-subscription). Then use the dsprts command to identify any through nodes (where the trunk is not terminated). Finally, look at the utilization factor for each of these lines using the dsputl and dspdutl commands. Figure 1-85 illustrates the dsptrkcons command display.

batman         TN    StrataCom       BPX 15    8.5       Aug. 9 1997  15:57 GMT
Connection Counts For TRK 5.1
Src Node  Conns    Src Node  Conns    Src Node  Conns    Src Node  Conns
batman    1765
Last Command: dsptrkcons 5.1
Next Command:

dsptrkmcons (Display Trunk Connection Counts by Master Node)

The dsptrkmcons command displays the number of connections routed over the specified trunk (BNI) by the master node.

Attributes

Jobs: No Log: Lock: Node Type: IPX, IGX, BPX

Associated Commands

dsptrkcons

Syntax

Function

This command displays the total number of connections being carried by the specified trunk. Rather than showing the remote end of the connection, the display lists the connection and the node that owns that connections.

This command is useful in determining the source of dropped packets in cases where the specified trunk is oversubscribed. First, use the dsptrkmcons command to list the trunks that originate at each node (the more connections per trunk, the greater the possibility of over-subscription). Next, use the dsprts command to identify any through-nodes (on which the trunk is not terminated). Finally, look at the utilization for each of these lines by using the dsputl and dspdutl commands. Figure 1-86 illustrates the dsptrkmcons command display.

sw81           TN    StrataCom       BPX 15    8.5    Aug. 26 1997 13:16 PST
Connection Counts For TRK 6.1
Mst Node  Conns    Mst Node  Conns    Mst Node  Conns    Mst Node  Conns
sw86      26
Last Command: dsptrkmcons 6.1
Next Command:

dsptrkstatcnf (Display Statistics Enabled For A Trunk)

The dsptrkstatcnf command displays the enabled statistics a physical or virtual trunk.

Attributes

Jobs: No Log: Yes Lock: Yes Node Type: IPX, IGX, BPX

Associated Commands

cnftrkstats

Syntax

Function

This command displays the statistics enabled for a trunk. It is intended for debugging statistics collection problems. It displays the trunk statistics set by the cnftrkstats command, by StrataView Plus, or by node features. Figure 1-87 shows example statistics for a T3 ATM trunk. The Owner column shows the source of the specification. If the Owner column shows "AUTO," the node's features determined the statistics. If the Owner column shows the name of the node, StrataView Plus determined the statistics. If the Owner column shows "USER," the cnftrkstats command was used to configure the statistics. The display may take up to four screens to display completely depending on statistics displayed.

sw81           TN    StrataCom       BPX 15    8.5 Oct. 22 1997 23:47 PST 
 
Statistics Enabled on Trunk 1.1
 
     Statistic                            Samples Interval Size Peaks Owner
     ------------------------------------ ------- -------- ---- ----- ----------
  3) Out of Frames                             60        0    4  NONE AUTO
  4) Loss of Signal                            60        0    4  NONE AUTO
 29) Line Code Violation                       60        0    4  NONE AUTO
 32) Line Parity Errors                        60        0    4  NONE AUTO
 35) Path Parity Errors                        60        0    4  NONE AUTO
 41) BIP-8 Errors                              60        0    4  NONE AUTO
 46) HCS Errors                                60        0    4  NONE AUTO
 48) Tx Voice Overflow Drpd Cells              60        0    4  NONE AUTO
 49) Tx TS Overflow Drpd Cells                 60        0    4  NONE AUTO
 50) Tx NTS Overflow Drpd Cells                60        0    4  NONE AUTO
 51) Tx Hi-Pri Overflow Drpd Cells             60        0    4  NONE AUTO
                                                                                
This Command: dsptrkstatcnf 1.1
 
 
Continue? y
sw81           TN    StrataCom       BPX 15    9.1.f7    Oct. 22 1997 23:48 PST 
 
Statistics Enabled on Trunk 1.1
 
     Statistic                            Samples Interval Size Peaks Owner
     ------------------------------------ ------- -------- ---- ----- ----------
 52) Tx BData A Overflow Drpd Cells            60        0    4  NONE AUTO
 53) Tx BData B Overflow Drpd Cells            60        0    4  NONE AUTO
 98) Frame Sync Errors                         60        0    4  NONE AUTO
167) Tx CBR Overflow Drpd Cells                60        0    4  NONE AUTO
168) Tx VBR Overflow Drpd Cells                60        0    4  NONE AUTO
169) Tx ABR Overflow Drpd Cells                60        0    4  NONE AUTO
 
 
 
 
 
                                                                                
Last Command: dsptrkstatcnf 1.1
 
 
Next Command: 

dsptrkstathist (Display Statistics History for a Trunk)

The dsptrkstathist command displays a history of configured statistics for a physical or virtual trunk.

Attributes

Jobs: No Log: Yes Lock: Yes Node Type: IPX, IGX, BPX

Associated Commands

cnftrkstats, dsptrkstatcnf

Syntax

Function

The dsptrkstathist command is a statistics debugging command. It displays the data for the last five occurrences of the selected statistic. The available trunk statistics appear on screen upon entry of the dsptrkstathist command. (The cnftrkstats command enables individual statistics. The dsptrkstatcnf command displays the enabled statistics for a trunk.) Figure 1-88 displays a statistic history for virtual trunk 1.1.1. The statistic is TX ABR Overflow Dropped Cells. This is statistic number 169, which execution of dsptrkstatcnf shows as enabled for this trunk. (If a disabled statistic is selected, a message stating this appears above the command line prompt.) The entered bucket interval is 0 minutes, which means that only the preceding 60 seconds worth of gathered data for number 169 appears.

sw97           TN    StrataCom       BPX 15    8.5       Aug. 9 1997  12:42 GMT
Tx ABR Overflow Drpd Cells on Trunk 1.1.1
Interval: 10 Second(s), Data Size: 4 Byte(s), NO Peaks, Owner: IPX
 0   -          0                       -11  -          0
-1   -          0                       -12  -          0
-2   -          0                       -13  -          0
-3   -          0                       -14  -          0
-4   -          0                       -15  -          0
-5   -          0                       -16  -          0
-6   -          0                       -17  -          0
-7   -          0                       -18  -          0
-8   -          0                       -19  -          0
-9   -          0                       -20  -          0
-10  -          0                       -21  -          0
This Command: dsptrkstathist 1.1.1 169 0 BPX
Continue?

dsputl (Display Utilization)

The dsputl command displays the utilization factor for all voice connections on a circuit line.

Attributes

Jobs: No Log: No Lock: Yes Node Type: IPX, IGX

Associated Commands

dspdutl

Syntax

Function

This command displays the actual percentage utilization for all voice connections on a single circuit line specified by the back slot (bslot) number. The percentage is calculated by dividing the number of packets transmitted over the total number of packets allocated to the specified channel. Only transmit packet rates are used. If percentage of actual utilization exceeds the configured utilization the channel appears in reverse video.

Figure 1-89 illustrates a typical display. In this example, the connections from 11.1 to 11.11 use VAD and the connections from 11.12 to 11.17 do not. The connections using VAD do not use any network bandwidth (0 utilization) until the connection is used. The other connections utilize the full bandwidth (100% utilization) even though they may be idle.

Use the dspdutl command to display utilization for data channels.

gamma            TRM       SuperUser        Rev:  8.5  Aug. 14 1997  16:36 PDT 
Percentage utilization        Last Cleared: Date/Time Not Set         Snapshot
CLN    1  2  3  4  5  6  7  8  9 10 11 12 13 14 15
11     0  0  0  0  0  0  0  0  0  0  0  0 99 99 99
CLN   16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 
11       99
Last Command: dsputl 11
Next Command:

forcerev (Force Revision)

The forcerev command forces a software revision to be sent down a trunk to a remote node.

Attributes

Jobs: No Log: Yes Lock: Yes Node Type: IPX, IGX, BPX

Associated Commands

dsprevs, loadrev

Syntax

Function

This command sends a change revision message blindly down the specified trunk from the local node to the remote node. This allows primary revisions to be changed regardless of communication breaks and unreachable nodes. Usage of this command should only be necessary if a problem results in inconsistent revisions throughout a network.

Figure 1-90 illustrates an example screen. If the local node does not have the SW revision specified, the system will display "Unavailable X.X" as indicated. Use the getfwrev command to load the desired software revision into the node. Use the dsprevs command to display the revisions available on each node in the network.

Caution Use this command only when requested by the Cisco TAC and under TAC supervision.

alpha            TRM       SuperUser        Rev:  8.5  Aug. 14 1997  13:42 PDT 
                   ------ Primary ------         ----- Secondary -----          
NodeName           Status       Revision         Status       Revision          
NodeName           Status       Revision         Status       Revision          
gamma              Running       8.5                                          
Last Command: forcerev 10 s 7.2
Next Command:

getfwrev (Get Firmware Revision)

The getfwrev command gets and loads a firmware image from StrataView, StrataView Plus, or a remote node into the specified node(s).

Attributes

Jobs: Yes Log: Yes Lock: Yes Node Type: IPX, IGX, BPX

Associated Commands

burnfwrev, dspfwrev, dspdnld

Syntax

Function

This command gets and loads a firmware revision image into the specified node's NPC memory. This firmware image can then be downloaded to specific interface cards within the node with the burnfwrev command. The firmware image must be already loaded into the StrataView or StrataView + terminal before using this command.

When the command is first entered, the status is temporarily "Unavailable" while the node attempts to locate the source of the firmware image. Once the download begins, a list of all of the files that make up the image is displayed and as the downloading progresses, the address of the file is updated.

• getfwrev a.b.cd *--loads firmware revision a.b.cd at all reachable nodes

• getfwrev a.b.cd nodename--loads firmware revision a.b.cd at one node only (nodename specifies the node).

• getfwrev 0.0.--clears a firmware revision image from NPC memory. Should be issued after every firmware download to clear the NPC memory.

Caution  This command is not to be confused with loadrev. It loads system software, not firmware.

loadcnf (Load Configuration)

The loadcnf command loads a configuration image from StrataView Plus to a node.

Attributes

Jobs: Yes Log: Yes Lock: Yes Node Type: IPX, IGX, BPX, IPX/AF

Associated Commands

dspcnf, runcnf, savecnf

Syntax

Function

This command causes a saved network configuration file to be downloaded from StrataView Plus to one node or all nodes. (See savecnf.) The configuration image downloaded is temporarily stored in a buffer area in a node's controller card memory. The process runs in the background and may take several minutes if the configuration file is large. Although loaded, the configuration is not yet restored. The configuration is restored to the controller card's BRAM memory using the runcnf command.

After loading and restoring a network configuration, the control card buffer area used for this purpose should be cleared so it is available for other downloading processes, such as that of firmware. To clear the buffer area, execute loadcnf with the clear parameter specified instead of backup_id. Specify the buffer of an individual node with node_name or all nodes with *. For the purpose of clearing the buffer area, do not specify the source_SV_node parameter.

To execute this command on an IPX/AF or IGX/AF interface shelf, telnet to the shelf or use a control terminal attached to the shelf.

loadrev (Load Revision)

The loadrev command loads a secondary system software revision image from StrataView or StrataView Plus into a node.

Attributes

Jobs: No Log: Yes Lock: Yes Node Type: IPX, IGX, BPX

Associated Commands

runrev, dsprevs, cnfdlparm

Syntax

Function

This command loads the secondary revision system software for the specified nodes. The secondary revision system software is the code that is loaded onto a controller card but is not being run. Use the runrev command after loading of a revision is complete to make the secondary revision the primary revision. The previous primary revision then becomes the secondary.

Examples of this command:

• loadrev a.b.cd *--loads revision a.b.cd at all reachable nodes.

• loadrev a.b.cd nodename--loads revision a.b.cd at nodename only

• loadrev 0.0.--clears a software revision image from controller memory. This command should be issued after every software download to clear the controller memory.

After entering the command, system responds with: "Enter Rev Number:" The dsprevs command is used to observe the software revisions that are currently loaded into the controller memory. The dspdnld command is used to display a running picture of the status of the download procedure once it has commenced.

Caution  Do not confuse loadrev with getfwrev. The getfwrev command loads firmware, not system software.

prtcderrs (Print Card Errors)

The prtcderrs command prints out detailed card failure information.

Attributes

Jobs: Yes Log: No Lock: Yes Node Type: IPX, IGX, BPX

Associated Commands

clrcderrs, dspcderrs

Syntax

Function

Prints a history of card failures associated with a specified slot on the network printer. If no argument is specified, a summary is printed, indicating the slots that have failures recorded against them. Refer to dspcderrs command for an example of a typical card error record that might be printed.

rrtcon (Reroute Connection)

The rrtcon command is used to manually reroute one or more connections.

Attributes

Jobs: Yes Log: Yes Lock: Yes Node Type: IPX, IGX, BPX

Associated Commands

drtop

Syntax

Function

This command forces a group, channel or range of channels to be rerouted. If a free-routing connection is rerouted by the system for whatever reason, it will not automatically return to its original route when the trouble clears. This may leave the connection on a path that is not the most direct or cost effective.

This command can be used to force a reroute that will likely put the connection back to its original route if available. Over time, many routes may need to be rerouted back to their original paths. In this case, use the "*" to reroute all connections.

To use this command you must first vt to the node that owns the connection (local node). If not at the local node, the system displays "This node is not owner of the connection(s)."

There is no provision for specifying a route. The node determines the connection route according to the same rules that are used when adding a new connection. If no network bandwidth is available for rerouting the connection, the node marks the connection as failed.

Caution  Using this command on a connection that is in service should be done with some discretion because the reroute interrupts service for as long as it takes to reroute the connection.

rststats (Reset Statistics Collection TIme)

The rststats command resets the statistics collection time for the tststats command.

Attributes

Jobs: Yes Log: No Lock: Yes Node Type: IPX, IGX

Associated Commands

tststats

Syntax

Function

This command resets the collection time for the tststats command. The tststats command displays a test statistics summary. Before there will be any meaningful statistics, the tstcon command must be performed on one or more network connections. Refer to the Cisco StrataCom Command Reference for information on the tstcon command. Figure 1-91 illustrates the system response.

alpha32        LAN   StrataCom       IPX 32    8.5     Aug. 30 1997 13:35 PST
Command history
12:
11:
10:
 9:
 8:
 7:
 6:
 5:
 4:
 3:
 2:
 1: rststats
This Command: rststats
Warning: This command clears all statistics
Continue?

runcnf (Run Configuration)

The runcnf command restores a network configuration image at one or all nodes.

Attributes

Jobs: No Log: Yes Lock: Yes Node Type: IPX, IGX, BPX, IPX/AF, IGX/AF

Associated Commands

savecnf, loadcnf, clrcnf

Syntax

Function

This command restores the specified configuration to the controller card's BRAM memory and overwrites the current configuration. Once restored, the specified node (or all nodes) rebuilds with the restored configuration image. To execute this command on an IPX/AF or IGX/AF interface shelf, telnet to the shelf or use a control terminal attached to the shelf.

This command is usually run after a previous configuration has been lost. If doubts exist about the state of the configuration at other nodes in the network, load the configuration into all nodes by specifying "*" for the node name. The new configuration must have previously been loaded into the controller buffer area with the loadcnf command.

Caution All network nodes must be run with the same configuration.

The system may display two warnings in response to the runcnf command:

A. When single node specified:

• Warning--node_name not reachable. Continue? Y/N.

• Warning--node_name does not have the specified configuration. Continue? Y/N.

B. When all nodes specified:

• Warning--all nodes not reachable. Continue? Y/N.

• Warning--all nodes do not have the specified configuration. Continue? Y/N.

If a single node is not reachable, responding with a "Y" does not affect the operation of the network. If node(s) do not all have the specified configuration or all are unreachable, it is not recommended that you continue until after the problem is resolved.

runrev (Run Revision)

The runrev command runs a specific revision of the system software revision at a node.

Attributes

Jobs: No Log: Yes Lock: Yes Node Type: IPX, IGX, BPX

Associated Commands

dsprevs, loadrev, cnfdlparm

Syntax

Function

This command sets the primary revision for the specified nodes. The primary software revision is the one that is actively controlling node operation. A non-active secondary revision that does not match the primary revision may also be loaded in the controller. To set the primary software revision, enter:

• runrev a.b.cd *--to run revision a.b.cd at all reachable nodes.

  or
  

• runrev a.b.cd nodename--to run revision a.b.cd at a single node (nodename) only.

After entering the command, system responds with "Enter Rev Number." Use the dsprevs command to determine which rev(s), primary and secondary, are available on the node. The runrev command will be ignored if the required revision is not present on the node.

You may need to load the new revision onto the StrataView Plus terminal and then use loadrev command to download the new software image into the standby controller before you issue the runrev command. If you enter a revision number that does not exist at the node, the system displays the message

"Warning--the node does not have the specified revision. Continue? Y/N"

Caution All network nodes must run with the same software revision to ensure normal network operation.

If you respond with "no," the system takes you back to the main StrataView Plus prompt and gives you an opportunity to change the revision number and re-attempt the operation.

savecnf (Save Configuration)

The savecnf command saves a configuration image on a StrataView Plus workstation disk.

Attributes

Jobs: Yes Log: Yes Lock: Yes Node Type: IPX, IGX, BPX, IPX/AF, IGX/AF

Associated Commands

loadcnf, runcnf, clrcnf

Syntax

Function

The savecnf command has two possible applications. It saves all the configurations for the nodes in a routing network, or it saves the configuration of one IPX/AF or IGX/AF interface shelf to a specific StrataView Plus workstation. Once saved, you can restore the configuration to BRAM by using the loadcnf and runcnf commands. You should execute savecnf in the following situations:

• After making any configuration changes in a network

• Before upgrading to a new system software release

Execution on a Routing Node

In a routing network, savecnf saves a configuration image for one node or all routing nodes (node_name = *) on the StrataView Plus workstation specified by dest_SV_node.

Execution on an IPX/AF or IGX/AF Interface Shelf

To execute savecnf on an IPX/AF or IGX/AF, either telnet to the shelf or use a control terminal attached to it: savecnf saves a configuration image of only the current shelf. The image is stored on the workstation with the IP address in the parameter dest_SV_ip. (In a routing network, dest_SV_ip is not necessary.) Note that node_name and dest_SV_node must both be the name of the shelf. The IP address of the destination StrataView Plus workstation uniquely identifies where to store the configuration image.

setfpevt (Set FastPAD Event Reporting)

The setfpevt command enables the reporting of FastPAD events.

Attributes

Jobs: No Log: Yes Lock: Yes Node Type: IPX, IGX

Associated Commands

clrfpevt, dsplog

Syntax

Function

Executing setfpevt restarts FastPAD event logging after you have stopped logging by using clrfpevt.

The reason for executing clrfpevt is to prevent the large number of logged events that accumulate when certain user-controlled disruptions occur. Without suspension of event-logging, the number of events caused by the disruption can cause the FastPAD to become unreachable. Examples of these events are:

• FTM Y-cable switchover

• NPM/NPC switchovers

• Adding a connection by using the addfrcons command

• Resetting the FastPAD (power cycling or by the resetfp command).

Example

setfpevt 9.3

Description

The example command resumes event logging for the FastPAD connected to port 9.3.

sw152          TN    StrataCom       IGX 16    8.5 Nov. 26 1997 15:14 GMT 
 
Most recent log entries (most recent at top)
Class  Description                                             Date     Time    
Info   FP fp93 event: 9.3.B grp:0-0 code:12                    11/26/97 15:13:28
Info   FP fp93 event: 9.3.B grp:0-0 code:1                     11/26/97 15:13:28
Info   User StrataCom logged in (Local)                        11/26/97 14:28:40
Info   User StrataCom logged in (Local)                        11/26/97 12:56:49
Info   Invalid Login Attempt via LAN Port (Local)              11/26/97 12:56:46
Info   User StrataCom logged in (Local)                        11/26/97 11:31:51
Info   AD  9.2.3   dallas   COM OK (Kickoff)                   11/26/97 11:23:17
Info   AD  9.2.3   dallas   Unreachable                        11/26/97 10:59:32
Info   AD  9.2.3   dallas   COM OK (Kickoff)                   11/26/97 10:56:54
Info   FP fp93 event: 9.3.B grp:0-0 code:12                    11/25/97 18:16:45
Info   FP fp93 event: 9.3.B grp:0-0 code:1                     11/25/97 18:16:45
                                                                                
Last Command: dsplog
 
 
Next Command: 

tststats (Test Statistics)

The tststats command displays a summary of the test statistics that result from performing a tstcon command on various network connections.

Attributes

Jobs: No Log: No Lock: No Node Type: IPX, IGX, BPX

Associated Commands

tstcon

Syntax

Function

Before tststats displays any meaningful statistics, the tstcon command must run on one or more network connections. Refer to the Cisco StrataCom Command Reference for information on the tstcon command. The following are displayed for voice, data, and Frame Relay connections.

• Tests Completed, Passed, Failed, and Aborted

• Failure data per failed connection (applies only to voice connections):

• Slot.channel--indicates which connection has failed.

• Good reads--indicates number of good reads on the test failure.

• Bad reads--indicates number of bad reads on the test failure.

Figure 1-92 illustrates a typical test statistics display.

sw150          TN    StrataCom       IGX 16    8.5      Aug. 1 1997  21:54 GMT
Connection Test results since: Date/Time Not Set
Type      Total      Passed      Failed      Aborted
Voice      0          0           0           0
Data       0          0           0           0
Fr Relay   0          0           0           0
Last Command: tststats
Next Command: