|
|
This appendix lists the pinouts for the cables you can use with Cisco 1600 series routers, and includes the following pinouts:
Table D-1 lists the pinouts for the 10BaseT port.
Table D-1 : 10BaseT Port Pinouts
| 8 Pin1 | Description |
|---|---|
| 1 | TX+ |
| 2 | TX-- |
| 3 | RX+ |
| 6 | RX-- |
Table D-2 lists the pinouts for a straight-through 10BaseT cable, which is used to connect the router to an Ethernet hub.
Table D-2 : Straight-Through 10BaseT Cable (RJ-45 to RJ-45)
| RJ-45
Pin |
Signal | Direction | RJ-45
Pin |
|---|---|---|---|
| 1 | TX+ | ---> | 1 |
| 2 | TX-- | ---> | 2 |
| 3 | RX+ | <--- | 3 |
| 4 | -- | -- | 4 |
| 5 | -- | -- | 5 |
| 6 | RX-- | <--- | 6 |
| 7 | -- | -- | 7 |
| 8 | -- | -- | 8 |
The EIA/TIA-232 console port is configured as data terminal equipment (DTE) and uses an RJ-45 connector. A console cable kit is provided with your router to connect a console (an ASCII terminal or PC running terminal emulation software) to the console port. The console cable kit contains an RJ-45-to-RJ-45 roll-over cable and a RJ-45-to-DB-25 female DTE adapter (labeled "Terminal"). Table D-3 lists the pinouts for the asynchronous serial console port, the RJ-45-to-RJ-45 roll-over cable, and the RJ-45-to-DB-25 female DTE adapter.
Table D-3 : Console Cable and Adapter Pinouts
| Console Port (DTE) | RJ-45-to-RJ-45 Roll-Over Cable | ||||
|---|---|---|---|---|---|
| Signal | RJ-45 Pin | RJ-45 Pin | DB-9 Pin | DB-25 Pin | Signal |
| -- | 1 | 8 | 7 | 4 | -- |
| DTR | 2 | 7 | 4 | 20 | DSR |
| TxD | 3 | 6 | 3 | 2 | RxD |
| GND | 4 | 5 | 5 | 7 | GND |
| GND | 5 | 4 | 5 | 7 | GND |
| RxD | 6 | 3 | 2 | 3 | TxD |
| DSR | 7 | 2 | 6 | 6 | DTR |
| -- | 8 | 1 | 8 | 5 | -- |
You can identify a roll-over cable by comparing the two modular ends of the cable. (See Figure D-1.) Holding the cables in your hand, side-by-side, with the tab at the back, the wire connected to the pin on the outside of the left connector (pin 1) should be the same color as the pin on the outside of the right connector (pin 8). On Cisco cables, pin 1 is white on one connector, and pin 8 is white on the other connector.
Figure D-1 : Identifying a Roll-Over Cable
Table D-4 lists the pinouts for an RJ48S-to-RJ48S cable, which is used to connect the Cisco 1602 to the 56-kbps wall jack.
Table D-4 : 56-kbps CSU/DSU (RJ-48S) Pinouts
| 8 Pin1 | Description |
|---|---|
| 1 | Transmit |
| 2 | Transmit |
| 7 | Receive |
| 8 | Receive |
Table D-5 : ISDN BRI S/T Port Pinouts (RJ-45)
| 8 Pin1 | TE2 | NT3 | Polarity |
|---|---|---|---|
| 3 | Transmit | Receive | + |
| 4 | Receive | Transmit | + |
| 5 | Receive | Transmit | -- |
| 6 | Transmit | Receive | -- |
Table D-6 : ISDN BRI U Port Pinouts (RJ-45)
| 8 Pin1 | Function |
|---|---|
| 3 | No connection |
| 4 | Signal---Tip or Ring |
| 5 | Signal---Tip or Ring |
| 6 | No connection |
Shielded Serial Transition Cable Pinouts
The serial port on the router uses a universal port, a 60-pin receptacle that supports the following serial interfaces: EIA/TIA-232, EIA/TIA-449, X.21, V.35, and EIA-530. The shielded serial transition cable determines the electrical interface type. The router end of all of the cables is a 60-pin connector.
DTE connectors have a plug connector at the network end. (DCE connectors have a receptacle at the network end.) However, V.35 is available in DTE mode with a connector of either gender at the network end. The serial port operates in DTE and DCE modes.
The tables that follow list the signal pinouts for the DTE mode serial transition cables for each router interface type.
Figure D-2 shows the EIA/TIA-232 serial cable assembly, and Table D-7 lists the EIA/TIA-232 cable pinouts.
Figure D-2 : EIA/TIA-232 Serial Cable Assembly
Table D-7 : EIA/TIA-232 DTE Cable Pinouts (DB-60 to DB-25)
| 60 Pin1 | Signal | Description | Direction | 25 Pin | Signal |
|---|---|---|---|---|---|
| J1-50
J1-51 J1-52 |
MODE_0
GND MODE_DCE |
Shorting group | -- | -- | -- |
| J1-46 | Shield GND | Single | -- | J2-1 | Shield GND |
| J1-41
Shield |
TxD/RxD
-- |
Twisted pair no. 5 | --->
-- |
J2-2
Shield |
TxD
-- |
| J1-36
Shield |
RxD/TxD
-- |
Twisted pair no. 9 | <---
-- |
J2-3
Shield |
RxD
-- |
| J1-42
Shield |
RTS/CTS
-- |
Twisted pair no. 4 | --->
-- |
J2-4
Shield |
RTS
-- |
| J1-35
Shield |
CTS/RTS
-- |
Twisted pair no. 10 | <---
-- |
J2-5
Shield |
CTS
-- |
| J1-34
Shield |
DSR/DTR
-- |
Twisted pair no. 11 | <---
-- |
J2-6
Shield |
DSR
-- |
| J1-45
Shield |
Circuit GND
-- |
Twisted pair no. 1 | --
-- |
J2-7
Shield |
Circuit GND
-- |
| J1-33
Shield |
DCD/LL
-- |
Twisted pair no. 12 | <---
-- |
J2-8
Shield |
DCD
-- |
| J1-37
Shield |
TxC/NIL
-- |
Twisted pair no. 8 | <---
-- |
J2-15
Shield |
TxC
-- |
| J1-38
Shield |
RxC/TxCE
-- |
Twisted pair no. 7 | <---
-- |
J2-17
Shield |
RxC
-- |
| J1-44
Shield |
LL/DCD
-- |
Twisted pair no. 2 | --->
-- |
J2-18
Shield |
LTST
-- |
| J1-43
Shield |
DTR/DSR
-- |
Twisted pair no. 3 | --->
-- |
J2-20
Shield |
DTR
-- |
| J1-39
Shield |
TxCE/TxC
-- |
Twisted pair no. 6 | --->
-- |
J2-24
Shield |
TxCE
-- |
Figure D-3 shows the EIA/TIA-449 serial cable assembly, and Table D-8 lists the EIA/TIA-449 cable pinouts.
Figure D-3 : EIA/TIA-449 Serial Cable Assembly
Table D-8 : EIA/TIA-449 DTE Cable Pinouts (DB-60 to DB-37)
| 60 Pin1 | Signal | Description | Direction | 37 Pin | Signal |
|---|---|---|---|---|---|
| J1-49
J1-48 |
MODE_1
GND |
Shorting group | -- | -- | -- |
| J1-51
J1-52 |
GND
MODE_DCE |
Shorting group | -- | -- | -- |
| J1-46 | Shield_GND | Single | _ | J2-1 | Shield GND |
| J1-11
J1-12 |
TxD/RxD+
TxD/RxD-- |
Twisted pair no. 6 | --->
---> |
J2-4
J2-22 |
SD+
SD-- |
| J1-24
J1-23 |
TxC/RxC+
TxC/RxC-- |
Twisted pair no. 9 | <---
<--- |
J2-5
J2-23 |
ST+
ST-- |
| J1-28
J1-27 |
RxD/TxD+
RxD/TxD-- |
Twisted pair no. 11 | <---
<--- |
J2-6
J2-24 |
RD+
RD-- |
| J1-9
J1-10 |
RTS/CTS+
RTS/CTS-- |
Twisted pair no. 5 | --->
---> |
J2-7
J2-25 |
RS+
RS-- |
| J1-26
J1-25 |
RxC/TxCE+
RxC/TxCE-- |
Twisted pair no. 10 | <---
<--- |
J2-8
J2-26 |
RT+
RT-- |
| J1-1
J1-2 |
CTS/RTS+
CTS/RTS-- |
Twisted pair no. 1 | <---
<--- |
J2-9
J2-27 |
CS+
CS-- |
| J1-44
J1-45 |
LL/DCD
Circuit_GND |
Twisted pair no. 12 | --->
_ |
J2-10
J2-37 |
LL
SC |
| J1-3
J1-4 |
DSR/DTR+
DSR/DTR-- |
Twisted pair no. 2 | <---
<--- |
J2-11
J2-29 |
DM+
DM-- |
| J1-7
J1-8 |
DTR/DSR+
DTR/DSR-- |
Twisted pair no. 4 | --->
---> |
J2-12
J2-30 |
TR+
TR-- |
| J1-5
J1-6 |
DCD/DCD+
DCD/DCD-- |
Twisted pair no. 3 | <---
<--- |
J2-13
J2-31 |
RR+
RR-- |
| J1-13
J1-14 |
TxCE/TxC+
TxCE/TxC-- |
Twisted pair no. 7 | --->
---> |
J2-17
J2-35 |
TT+
TT-- |
| J1-15
J1-16 |
Circuit_GND
Circuit_GND |
Twisted pair no. 9 | --
-- |
J2-19
J2-20 |
SG
RC |
Figure D-4 shows the X.21 cable assembly, and Table D-9 lists the X.21 cable pinouts.
Figure D-4 : X.21 Cable Assembly
Table D-9 : X.21 DTE Cable Pinouts (DB-60 to DB-15)
| 60 Pin1 | Signal | Description | Direction | 15 Pin | Signal |
|---|---|---|---|---|---|
| J1-48
J1-47 |
GND
MODE_2 |
Shorting group | -- | -- | -- |
| J1-51
J1-52 |
GND
MODE_DCE |
Shorting group | -- | -- | -- |
| J1-46 | Shield_GND | Single | -- | J2-1 | Shield GND |
| J1-11
J1-12 |
TxD/RxD+
TxD/RxD-- |
Twisted pair no. 3 | --->
---> |
J2-2
J2-9 |
Transmit+
Transmit-- |
| J1-9
J1-10 |
RTS/CTS+
RTS/CTS-- |
Twisted pair no. 2 | --->
---> |
J2-3
J2-10 |
Control+
Control-- |
| J1-28
J1-27 |
RxD/TxD+
RxD/TxD-- |
Twisted pair no. 6 | <---
<--- |
J2-4
J2-11 |
Receive+
Receive-- |
| J1-1
J1-2 |
CTS/RTS+
CTS/RTS-- |
Twisted pair no. 1 | <---
<--- |
J2-5
J2-12 |
Indication+
Indication-- |
| J1-26
J1-25 |
RxC/TxCE+
RxC/TxCE-- |
Twisted pair no. 5 | <---
<--- |
J2-6
J2-13 |
Timing+
Timing-- |
| J1-15
Shield |
Control_GND
-- |
Twisted pair no. 4 | --
-- |
J2-8
Shield |
Control GND
-- |
Figure D-5 shows the V.35 cable assembly and Table D-10 lists the V.35 cable pinouts.
Figure D-5 : V.35 Cable Assembly
Table D-10 : V.35 Cable Pinouts (DB-60 to 34-Pin)
| 60 Pin1 | Signal | Description | Direction | 34 Pin | Signal |
|---|---|---|---|---|---|
| J1-49
J1-48 |
MODE_1
GND |
Shorting group | -- | -- | -- |
| J1-50
J1-51 J1-52 |
MODE_0
GND MODE_DCE |
Shorting group | -- | -- | -- |
| J1-53
J1-54 J1-55 J1-56 |
TxC/NIL
RxC_TxCE RxD/TxD GND |
Shorting group | -- | -- | -- |
| J1-46 | Shield_GND | Single | -- | J2-A | Frame GND |
| J1-45
Shield |
Circuit_GND
-- |
Twisted pair no. 12 | --
-- |
J2-B
Shield |
Circuit GND
-- |
| J1-42
Shield |
RTS/CTS
-- |
Twisted pair no. 9 | --->
-- |
J2-C
Shield |
RTS
-- |
| J1-35
Shield |
CTS/RTS
-- |
Twisted pair no. 8 | <---
-- |
J2-D
Shield |
CTS
-- |
| J1-34
Shield |
DSR/DTR
-- |
Twisted pair no. 7 | <---
-- |
J2-E
Shield |
DSR
-- |
| J1-33
Shield |
DCD/LL
-- |
Twisted pair no. 6 | <---
-- |
J2-F
Shield |
RLSD
-- |
| J1-43
Shield |
DTR/DSR
-- |
Twisted pair no. 10 | --->
-- |
J2-H
Shield |
DTR
-- |
| J1-44
Shield |
LL/DCD
-- |
Twisted pair no. 11 | --->
-- |
J2-K
Shield |
LT
-- |
| J1-18
J1-17 |
TxD/RxD+
TxD/RxD-- |
Twisted pair no. 1 | --->
---> |
J2-P
J2-S |
SD+
SD-- |
| J1-28
J1-27 |
RxD/TxD+
RxD/TxD-- |
Twisted pair no. 5 | <---
<--- |
J2-R
J2-T |
RD+
RD-- |
| J1-20
J1-19 |
TxCE/TxC+
TxCE/TxC-- |
Twisted pair no. 2 | --->
---> |
J2-U
J2-W |
SCTE+
SCTE-- |
| J1-26
J1-25 |
RxC/TxCE+
RxC/TxCE-- |
Twisted pair no. 4 | <---
<--- |
J2-V
J2-X |
SCR+
SCR-- |
| J1-24
J1-23 |
TxC/RxC+
TxC/RxC-- |
Twisted pair no. 3 | <---
<--- |
J2-Y
J2-AA |
SCT+
SCT-- |
Figure D-6 shows the EIA-530 cable assembly, and Table D-11 lists the EIA-530 DTE cable pinouts.
Figure D-6 : EIA-530 Cable Assembly
Table D-11 : EIA-530 DTE Cable Pinouts (DB-60 to DB-25)
|
60 Pin1 |
Signal |
25 Pin |
Signal |
Direction
DTE DCE2 |
|---|---|---|---|---|
| J1-11
J1-12 |
TxD/RxD+
TxD/RxD-- |
J2-2
J2-14 |
BA(A), TxD+
BA(B), TxD-- |
--->
---> |
| J1-28
J1-27 |
RxD/TxD+
RxD/TxD-- |
J2-3
J2-16 |
BB(A), RxD+
BB(B), RxD-- |
<---
<--- |
| J1-9
J1-10 |
RTS/CTS+
RTS/CTS-- |
J2-4
J2-19 |
CA(A), RTS+
CA(B), RTS-- |
--->
---> |
| J1-1
J1-2 |
CTS/RTS+
CTS/RTS-- |
J2-5
J2-13 |
CB(A), CTS+
CB(B), CTS-- |
<---
<--- |
| J1-3
J1-4 |
DSR/DTR+
DSR/DTR-- |
J2-6
J2-22 |
CC(A), DSR+
CC(B), DSR-- |
<---
<--- |
| J1-46
J1-47 |
Shield_GND
MODE_2 |
J2-1
-- |
Shield
-- |
Shorted |
| J1-48
J1-49 |
GND
MODE_1 |
--
-- |
--
-- |
Shorted |
| J1-5
J1-6 |
DCD/DCD+
DCD/DCD-- |
J2-8
J2-10 |
CF(A), DCD+
CF(B), DCD-- |
<---
<--- |
| J1-24
J1-23 |
TxC/RxC+
TxC/RxC-- |
J2-15
J2-12 |
DB(A), TxC+
DB(B), TxC-- |
<---
<--- |
| J1-26
J1-25 |
RxC/TxCE+
RxC/TxCE-- |
J2-17
J2-9 |
DD(A), RxC+
DD(B), RxC-- |
<---
<--- |
| J1-44
J1-45 |
LL/DCD
Circuit_GND |
J2-18
J2-7 |
LL
Circuit_ GND |
--->
-- |
| J1-7
J1-8 |
DTR/DSR+
DTR/DSR-- |
J2-20
J2-23 |
CD(A), DTR+
CD(B), DTR-- |
--->
---> |
| J1-13
J1-14 |
TxCE/TxC+
TxCE/TxC-- |
J2-24
J2-11 |
DA(A), TxCE+
DA(B), TxCE-- |
--->
---> |
|
Copyright 1988-1996 © Cisco Systems Inc.