|
|
This appendix provides the following pinout information:
The access server comes with a console and auxiliary cable kit, which contains the cable and adapters you need to connect a console (an ASCII terminal or PC running terminal emulation software) or modem to your access server. The console and auxiliary cable kit includes:
For console connections, proceed to the section "Console Port Signals and Pinouts" later in this appendix; for modem connections, proceed to the section "Auxiliary Port Signals and Pinouts" later in this appendix.
You can identify a rollover cable by comparing the two modular ends of the cable. Holding the cables side-by-side, with the tab at the back, the wire connected to the pin on the outside of the left plug should be the same color as the wire connected to the pin on the outside of the right plug. (See Figure C-1.) If your cable was purchased from Cisco Systems, pin 1 will be white on one connector, and pin 8 will be white on the other connector (a rollover cable reverses pins 1 and 8, 2 and 7, 3 and 6, and 4 and 5).
Use the RJ-45-to-RJ-45 rollover cable and RJ-45-to-DB-9 female DTE adapter (labeled TERMINAL) to connect the console port to a PC running terminal emulation software. Figure C-2 shows how to connect the console port to a PC. Table C-1 lists the pinouts for the asynchronous serial console port, the RJ-45-to-RJ-45 rollover cable, and the RJ-45-to-DB-9 female DTE adapter (labeled TERMINAL).
| Console Port (DTE) | RJ-45-to-RJ-45 Rollover Cable | RJ-45-to-DB-9 Terminal Adapter | Console Device | |
|---|---|---|---|---|
| Signal | RJ-45 Pin | RJ-45 Pin | DB-9 Pin | Signal |
| RTS | 11 | 8 | 8 | CTS |
| DTR | 2 | 7 | 6 | DSR |
| TxD | 3 | 6 | 2 | RxD |
| GND | 4 | 5 | 5 | GND |
| GND | 5 | 4 | 5 | GND |
| RxD | 6 | 3 | 3 | TxD |
| DSR | 7 | 2 | 4 | DTR |
| CTS | 81 | 1 | 7 | RTS |
Use the RJ-45-to-RJ-45 rollover cable and RJ-45-to-DB-25 female DTE adapter (labeled TERMINAL) to connect the console port to a terminal. Figure C-3 shows how to connect the console port to a terminal. Table C-2 lists the pinouts for the asynchronous serial console port, the RJ-45-to-RJ-45 rollover cable, and the RJ-45-to-DB-25 female DTE adapter (labeled TERMINAL).
| Console Port (DTE)1 | RJ-45-to-RJ-45 Rollover Cable | RJ-45-to-DB-25 Terminal Adapter | Console Device | |
|---|---|---|---|---|
| Signal | RJ-45 Pin | RJ-45 Pin | DB-25 Pin | Signal |
| RTS | 12 | 8 | 5 | CTS |
| DTR | 2 | 7 | 6 | DSR |
| TxD | 3 | 6 | 3 | RxD |
| GND | 4 | 5 | 7 | GND |
| GND | 5 | 4 | 7 | GND |
| RxD | 6 | 3 | 2 | TxD |
| DSR | 7 | 2 | 20 | DTR |
| CTS | 81 | 1 | 4 | RTS |
Use the RJ-45-to-RJ-45 rollover cable and RJ-45-to-DB-25 male DCE adapter (labeled MODEM) to connect the auxiliary port to a modem. Figure C-4 shows how to connect the auxiliary port to a modem. Table C-3 lists the pinouts for the asynchronous serial auxiliary port, the RJ-45-to-RJ-45 rollover cable, and the RJ-45-to-DB-25 male DCE adapter (labeled MODEM).
| AUX Port (DTE) | RJ-45-to-RJ-45 Rollover Cable | RJ-45-to-DB-25 Modem Adapter | Modem | |
|---|---|---|---|---|
| Signal | RJ-45 Pin | RJ-45 Pin | DB-25 Pin | Signal |
| RTS | 1 | 8 | 4 | RTS |
| DTR | 2 | 7 | 20 | DTR |
| TxD | 3 | 6 | 3 | TxD |
| GND | 4 | 5 | 7 | GND |
| GND | 5 | 4 | 7 | GND |
| RxD | 6 | 3 | 2 | RxD |
| DSR | 7 | 2 | 8 | DCD |
| CTS | 8 | 1 | 5 | CTS |
Table C-4 and Table C-5 list the pinouts for the Ethernet 10BaseT and 100BaseT ports, respectively.
| RJ-45 Pin | Description |
|---|---|
| 1 | TX+ |
| 2 | TX- |
| 3 | RX+ |
| 4 | - |
| 5 | - |
| 6 | RX- |
| 7 | - |
| 8 | - |
| RJ-45 Pin | Description |
|---|---|
| 1 | RXD+ |
| 2 | RXD- |
| 3 | TXD+ |
| 4 | - |
| 5 | - |
| 6 | TXD- |
| 7 | - |
| 8 | - |
Table C-6 lists the quad T1 PRI card port pinouts. Use a straight-through RJ-45-to-RJ-45 cable to connect the T1 port to an RJ-45 jack.
| RJ-45 Pin | Description |
|---|---|
| 1 | RX Tip |
| 2 | RX Ring |
| 3 | RX Shield |
| 4 | TX Tip |
| 5 | TX Ring |
| 6 | TX Shield |
| 7 | - |
| 8 | - |
Eight serial cables are available from Cisco Systems for connecting the E1/PRI card ports:
| Cable Description | Part Number | Product Number |
|---|---|---|
RJ-45 to DB-15 | 72-1336-01 | CAB-T1-RJ45DB15 |
| RJ-45 to DB-15 Null | 72-1337-01 | CAB-T1-RJ45DB15N |
| RJ-45 to BNC | 72-1338-01 | CAB-E1-RJ45BNC |
| RJ-45 to Twinax | 72-1339-01 | CAB-E1-RJ45TWIN |
| RJ-45 to RJ-45 TE | 72-1340-01 | CAB-T1-RJ45TE |
| RJ-45 to RJ-45 NT | 72-1341-01 | CAB-T1-RJ45NT |
| RJ-45 to RJ-45 T1 | 72-1342-01 | CAB-T1-RJ45 |
| RJ-45 to Bare | 72-1343-01 | CAB-T1-RJ45BARE |
| RJ-45 Pin | Signal | Description | Direction | DB-15 Pin |
|---|---|---|---|---|
| Shield | Ground | Shell/Braid | Shell | |
| J1-1 | RX Tip | Twisted Pair #1 | <-- | J2-3 |
| J1-2 | RX Ring | Twisted Pair #1 | <-- | J2-11 |
| J1-3 | RX Shield | Twisted Pair #3 | J2-4 | |
| J1-4 | TX Tip | Twisted Pair #2 | --> | J2-1 |
| J1-5 | TX Ring | Twisted Pair #2 | --> | J2-9 |
| J1-6 | TX Shield | Twisted Pair #4 | J2-2 |
| RJ-45 Pin | Signal | Description | Direction | DB-15 Pin |
|---|---|---|---|---|
| Shield | Ground | Shell/Braid | Shell | |
| J1-1 | RX Tip | Twisted Pair #1 | <-- | J2-1 |
| J1-2 | RX Ring | Twisted Pair #1 | <-- | J2-9 |
| J1-3 | RX Shield | Twisted Pair #3 | J2-2 | |
| J1-4 | TX Tip | Twisted Pair #2 | --> | J2-3 |
| J1-5 | TX Ring | Twisted Pair #2 | --> | J2-11 |
| J1-6 | TX Shield | Twisted Pair #4 | J2-4 |
| RJ-45 Pin | Signal | Description | Direction | BNC Pin |
|---|---|---|---|---|
| Shield | Ground | Shell | RX, TX Shields | |
| J1-1 | RX Tip | Twisted Pair #1 | <-- | RX-Tip |
| J1-2 | RX Ring | Twisted Pair #1 | <-- | RX-Shield |
| J1-3 | RX Shield | Twisted Pair #3 | RX-Shield | |
| J1-4 | TX Tip | Twisted Pair #2 | --> | TX-Tip |
| J1-5 | TX Ring | Twisted Pair #2 | --> | TX-Shield |
| J1-6 | TX Shield | Twisted Pair #4 | TX-Shield |
| RJ-45 Pin | Signal | Description | Direction | Twinax Pin |
|---|---|---|---|---|
| Shield | Ground | Shell | RX, TX Shields | |
| J1-1 | RX Tip | Twisted Pair #1 | <-- | RX-1 |
| J1-2 | RX Ring | Twisted Pair #1 | <-- | RX-2 |
| J1-3 | RX Shield | Twisted Pair #3 | RX Shield | |
| J1-4 | TX Tip | Twisted Pair #2 | --> | TX-1 |
| J1-5 | TX Ring | Twisted Pair #2 | --> | TX-2 |
| J1-6 | TX Shield | Twisted Pair #4 | TX Shield |
| RJ-45 Pin | Signal | Description | Direction | RJ-45 TE Pin |
|---|---|---|---|---|
| Shield | Ground | Shell/Braid | Shield | |
| J1-1 | RX Tip | Twisted Pair #1 | <-- | J2-1 |
| J1-2 | RX Ring | Twisted Pair #1 | <-- | J2-2 |
| J1-3 | RX Shield | Twisted Pair #3 | J2-3 | |
| J1-4 | TX Tip | Twisted Pair #2 | --> | J2-4 |
| J1-5 | TX Ring | Twisted Pair #2 | --> | J2-5 |
| J1-6 | TX Shield | Twisted Pair #4 | J2-6 |
| RJ-45 Pin | Signal | Description | Direction | Signal | RJ-45 NT Pin |
|---|---|---|---|---|---|
| Shield | Ground | Shell/Braid | Ground | Shield | |
| J1-1 | RX Tip | Twisted Pair #1 | <-- | TX Tip | J2-4 |
| J1-2 | RX Ring | Twisted Pair #1 | <-- | TX Ring | J2-5 |
| J1-3 | RX Shield | Twisted Pair #3 | TX Shield | J2-6 | |
| J1-4 | TX Tip | Twisted Pair #2 | --> | RX Tip | J2-1 |
| J1-5 | TX Ring | Twisted Pair #2 | --> | RX Ring | J2-2 |
| J1-6 | TX Shield | Twisted Pair #4 | RX Shield | J2-3 |
| RJ-45 Pin | Signal | Description | Direction | RJ-45 T1 Pin |
|---|---|---|---|---|
| Shield | Ground | Shell/Braid | Shield | |
| J1-1 | RX Tip | Twisted Pair #1 | <-- | J2-1 |
| J1-2 | RX Ring | Twisted Pair #1 | <-- | J2-2 |
| J1-3 | RX Shield | |||
| J1-4 | TX Tip | Twisted Pair #2 | --> | J2-4 |
| J1-5 | TX Ring | Twisted Pair #2 | --> | J2-5 |
| J1-6 | TX Shield |
| RJ-45 Pin | Signal | Description | Direction | Bare |
|---|---|---|---|---|
| Shield | Ground | Braid | ||
| J1-1 | RX Tip | Twisted Pair #1 | <-- | WIRE-1 |
| J1-2 | RX Ring | Twisted Pair #1 | <-- | WIRE-2 |
| J1-3 | RX Shield | |||
| J1-4 | TX Tip | Twisted Pair #2 | --> | WIRE-3 |
| J1-5 | TX Ring | Twisted Pair #2 | --> | WIRE-4 |
| J1-6 | TX Shield |
|
|