|
|
The LightStream 1010 ATM switch system specifications are described in Table A-1.
Table A-1 : System Specifications
| Description | Specifications |
|---|---|
| Switch and Processor Capacity | 5 Gbps1 shared memory, nonblocking switch fabric
65,536 cells of ATM cell buffers |
| Software Images | Default image with IISP protocol
Optional PNNI image with plug-and-play capacity |
| Dimensions (H x W x D) | 10.4 x 17.25 x 18.4" (26.4 x 43.1 x 46.0 cm)
Chassis depth including cable guide is 21.64" (55.0 cm) (L1010-BASE5) ASP and CAM: 1.2 x 14.4 x 16" (3.0 x 36.6 x 40.6 cm) PAM: 1.2 x 6.5 x 10" (3.0 x 16.5 x 25.4 cm) |
| Weight | Chassis only: 32 lb (13.6 kg)
Chassis fully configured with 1 ASP, 8 PAMs, and 2 power supplies: 67 lb (30 kg) |
| DC Voltages Supplied and Steady-state Maximum Current Ratings | +5V @ 70A
+12V @ 2A +24V @ 0.2A |
| Power Supply | 376W maximum (AC-input power supplies) (L1010-PWR-1) |
| Power Dissipation | 350W maximum configuration, 110W typical with maximum configuration |
| Heat Dissipation | 563W (1919 Btu2/hr) |
| Input Voltage | 100--240 VAC wide input with power factor correction |
| Frequency | Auto sensing limits: 100-127/200-240 VAC, 8/4A, 47-63 Hz |
| AC Current Rating | Maximum power budget: 8A @ 115 VAC, 60 Hz 4A @ 230 VAC, 50 Hz with the chassis fully configured |
| Airflow | 95 cfm3 through the system fan assembly |
| Operating Temperature | 32--104°F (0--40°C) |
| Nonoperating Temperature | -40--167°F (-40--75°C) |
| Humidity | 10--90%, noncondensing |
| Altitude | -500 to 10,000 ft (-52 to 3,048 m) |
| Microprocessor | 100-MHz MIPS R4600 |
| Memory | 8 MB of Flash memory (upgradable to 16 MB)
16 MB of packet-buffer DRAM4 standard (upgradable to 64 MB) 256 KB of boot EPROM 128 KB of SRAM5 |
| Interface Timing | Loop timing, Stratum 4 accuracy clock for self-timing, master clock distribution port |
| ATM Switch Processor (ASP) | ASP module, 16-MB DRAM, 8-MB Flash memory, no Flash card installed (WATM-ASP1) |
| Carrier Adapter Module (CAM) | Carrier module for 2-port adapter modules with PAM slot covers for empty slots installed (WATM-CAM -2P) |
| Port Adapter Modules (PAM) | PAM with 4 SONET STS3c/SDH STM1 multimode fiber ports, SC connectors (WAI-OC3-4MM)
PAM with 4 SONET STS3c/SDH STM1 single-mode fiber ports, SC connectors (WAI-OC3-4SM) PAM with 4 SONET STS3c/SDH STM1 UTP-5 ports, RJ-45 connectors (WAI-C3-4U5) PAM with 1SONET STS12c/SDH STM4c single-mode fiber ports, SC connector (WAI-OC12-1SM) PAM with 1SONET STS12c/SDH STM4c multimode fiber ports, SC connector (WAI-OC12-1MM) PAM with 4 DS3 ports, BNC connectors (WAI-T3-2BNC) PAM with 2 E3 ports, BNC connectors (WAI-E3-2BMC) |
| Management Access | Standard Ethernet and dual EIA/TIA 232 serial ports on ASP module |
| Connections | 32,000 point-to-point, 2,048 multi-to-multipoint
VC and VP switching, VP tunneling PVC and SVC F4 and F5 OAM6 segment and end-to-end flows, RDI7 and AIS8 OAM PING on IP or ATM address |
| Signaling and Routing | UNI 3.0, UNI 3.1 in future release
ILMI PNNI Phase 1, IISP Soft PVC/PVP support ATM access list and firewalls Crankback Plug-and-play mode with PNNI image Redundant link support with load balancing or best-fit selection |
| Traffic Management | Single, dual-mode leaky-bucket traffic policing
Per-port traffic pacing Multiple configurations per connection, port, and switch threshold Multiple priority classes All ATM connection types and AALs Connection Admission Control CLP9 tagging and discard Intelligent packet discard Available bit rate support: EFCI10 marking mode and relative rate marking mode |
| ASP Interface Ports | RJ-45 IEEE 802.3 Ethernet 10BaseT port
25-pin EIA/TIA-23211 AUX port and a DB-25 console port for an administration workstation |
| Network Management | Port TX and RX LEDs, switch and common equipment status LEDs
Port snooping and connection steering Multiple standard and enterprise MIBs Text-based command line interface based on familiar router interface Standard Cisco IOS security capabilities: password and TACACS,12 Telnet, TFTP, BOOTP, LAN Emulation client, RFC 1577 Classical IP over ATM client (for management access) |
| Mean Time Between Failures | 2.6 years for system configuration |
| Management Information Bases (MIB) | SNMP MIB II (RFC 1213)
Interface table MIB (RFC 1573) AToMIC (RFC 1695) ATM Forum LANE A MIB ATM Forum PNNI MIB SONET MIB (RFC 1595) ATM Forum UNI 30/3.11 ILMI MIB DS-3 and E3 MIB (RFC 1407) RMON MIB (RFC 1757) Ethernet MIB (RFC 1398) RS-232 MIB (RFC 1659) |
| Maximum
Station-to-station Cabling Distance |
10BaseT Ethernet---Category 3-5 UTP13: 328' (100 m)
ATM multimode---50/125-micron and 62.5/125-micron multimode fiber: 1.24 miles (2 km) ATM single-mode---8/125-micron single-mode fiber: 9 miles (15 km) DS-3---coaxial cable: 450 ft (137 m) E3---coaxial cable: 450 ft (137 m) OC-12---8/125-micron single-mode fiber: 9 miles (15 km) OC-12---50/125-micron and 62.5/125-micron multimode fiber: 1,640 ft (500 m) |
| Fiber-Optic Power Levels:
OC-3 Single-mode Output Center Wavelength Transmit Receive |
1261 to 1360 nm14 Minimum: -15.0 dBm Maximum: -8.0 dBm Minimum: -30.0 dBm Maximum: -8.0 dBm |
| OC-3 Multimode
Output Center Wavelength Transmit Receive |
1270 to 1380 nm Minimum: -20.0 dBm Maximum: -14.0 dBm Minimum: -30.0 dBm Maximum: -14.0 dBm |
| Fiber-optic power levels: (cont.)
OC-12 Single-mode Output Center Wavelength Transmit Receive OC-12 Multimode Output Center Wavelength Transmit Receive |
1274 to 1356 nm Minimum: -15.0 dBm Maximum: -8.0 dBm Minimum: -28.0 dBm Maximum: -8.0 dBm 1270 to 1380 nm Minimum: -20.0 dBm Maximum: -14.0 dBm Minimum: -26.0 dBm Maximum: -14.0 dBm |
| Agency Approvals | Safety: UL15 1950, CSA16-C22.2 No. 950-93, and EN60950
EMI17: FCC Class A CE Mark, and VCCI Class II with shielded cables |
|
Copyright 1988-1996 © Cisco Systems Inc.